Jiadong Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jiadong Hu has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Haiyun Xia
The State Key Laboratory of Climate System Prediction and Risk Management (CPRM), School of Atmospheric Physics, Nanjing University of Information Science & Technology, Nanjing, 210044, China
3 shared publications - Shubin Liu
University of Science and Technology of China
3 shared publications Qi An
State Key Laboratory of Particle Detection and Electronics, University of Science and Technology of China 1 , Hefei 230026, China
2 shared publications- Tianwen Wei
The State Key Laboratory of Climate System Prediction and Risk Management (CPRM), School of Atmospheric Physics, Nanjing University of Information Science & Technology, Nanjing, 210044, China
2 shared publications - Zhe Cao
University of Science and Technology of China, Hefei, China
2 shared publications Boyu Cheng
State Key Laboratory of Particle Detection and Electronics, University of Science and Technology of China, Hefei 230026, China and Department of Modern Physics, University of Science and Technology of China, Hefei 230026, China
1 shared publication
Latest Publications
- Open Access
- 2 April 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (7) , 1072
Hail Event Detection Using Power Spectrum Characteristics of Coherent Doppler Lidar: A Case Study in Hefei
Hail is one of the typical manifestations of severe convective weather, characterized by its sudden onset and strong localization. In this study, a compact all-fiber coherent Doppler lidar (CDL) working at the 1.5 μm wavelength is employed to detect a hail event. Combined with ERA5 reanalysis data, Parsivel2, and cloud-type products from the Fengyun satellite, the synoptic background of the hail event was analyzed. Owing to its high-precision spectrum measurement capability, the CDL can effectively separate the multi-component power spectra of precipitation particles. By comparing particle velocity, spectrum width and skewness as characteristic parameters from signal separation across light rain, hail and heavy rain, the distinctive power spectrum characteristics of hail were identified. This study verifies that CDL can provide high-spatiotemporal-resolution data support for the short-term forecasting of hail events.
- 2 April 2026
- Published by MDPI AG in Remote Sensing
- Vol. 18 (7) , 1072
Open AccessHail Event Detection Using Power Spectrum Characteristics of Coherent Doppler Lidar: A Case Study in Hefei
Hail is one of the typical manifestations of severe convective weather, characterized by its sudden onset and strong localization. In this study, a compact all-fiber coherent Doppler lidar (CDL) working at the 1.5 μm wavelength is employed to detect a hail event. Combined with ERA5 reanalysis data, Parsivel2, and cloud-type products from the Fengyun satellite, the synoptic background of the hail event was analyzed. Owing to its high-precision spectrum measurement capability, the CDL can effectively separate the multi-component power spectra of precipitation particles. By comparing particle velocity, spectrum width and skewness as characteristic parameters from signal separation across light rain, hail and heavy rain, the distinctive power spectrum characteristics of hail were identified. This study verifies that CDL can provide high-spatiotemporal-resolution data support for the short-term forecasting of hail events.
- 24 February 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 199
Simultaneous multi-gas detection using IPDA lidar with InGaAs/InP single-photon detector
- 24 February 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 199
Simultaneous multi-gas detection using IPDA lidar with InGaAs/InP single-photon detector
- Open Access
- 9 September 2025
- Published by MDPI AG in Remote Sensing
- Vol. 17 (18) , 3127
Detection and Analysis of Airport Tailwind Events Triggered by Frontal Activity
Excessive tailwind, threatening the safety of aircraft takeoff and landing, is one of the prominent research topics in the field of aviation meteorology. This paper analyzes the causes of tailwinds at Beijing Daxing International Airport (BDIA), based on coherent Doppler wind lidar (CDWL) and ERA5 reanalysis data. CDWL with high spatiotemporal resolution is utilized to detect variations in the low-level wind field in the vicinity of airport areas. ERA5 reanalysis data are employed to investigate the distribution characteristics of meteorological elements such as wind fields, pressure, and temperature in the Beijing surrounding regions. The study of two typical tailwind events reveals that frontal activity, through the combined effects of pressure gradient adjustment and topographic constraints from the Taihang Mountains, drives the development of low-level southerly jets. It serves as the key mechanism triggering excessive tailwind. By integrating CDWL and ERA5 data for local and regional analysis, this study contributes to enhancing understanding of tailwind causal mechanisms and provides critical support for aviation meteorological disaster early warning.
- 9 September 2025
- Published by MDPI AG in Remote Sensing
- Vol. 17 (18) , 3127
Open AccessDetection and Analysis of Airport Tailwind Events Triggered by Frontal Activity
Excessive tailwind, threatening the safety of aircraft takeoff and landing, is one of the prominent research topics in the field of aviation meteorology. This paper analyzes the causes of tailwinds at Beijing Daxing International Airport (BDIA), based on coherent Doppler wind lidar (CDWL) and ERA5 reanalysis data. CDWL with high spatiotemporal resolution is utilized to detect variations in the low-level wind field in the vicinity of airport areas. ERA5 reanalysis data are employed to investigate the distribution characteristics of meteorological elements such as wind fields, pressure, and temperature in the Beijing surrounding regions. The study of two typical tailwind events reveals that frontal activity, through the combined effects of pressure gradient adjustment and topographic constraints from the Taihang Mountains, drives the development of low-level southerly jets. It serves as the key mechanism triggering excessive tailwind. By integrating CDWL and ERA5 data for local and regional analysis, this study contributes to enhancing understanding of tailwind causal mechanisms and provides critical support for aviation meteorological disaster early warning.
- 1 May 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (5)
Weak signal detection technique based on Durbin–Watson test and one-bit sampling
Correlation-based detection techniques are widely used in the weak periodic signal detection field. Traditionally, they are based on extracting the correlation of a weak signal from noise. Considering the impact of a weak signal on the randomness of background noise, this article takes the opposite approach and proposes a weak signal detection technique based on the Durbin–Watson (DW) test and one-bit sampling, detecting the weak signal due to the extent to which the randomness of noise is affected. The randomness of noise is analyzed through the DW test, which is a method for detecting the randomness of data sequences through first-order autocorrelation. One-bit sampling is adopted to reduce the complexity of the sampling circuit and data processing algorithm. The effectiveness of the DW test in the situation of one-bit sampling is demonstrated through simulation and analysis. Simulation results show that the proposed technique is capable of detecting weak sinusoidal and square-wave signals with a signal-to-noise ratio (SNR) above −30 dB, and the frequency or SNR of a weak signal can be further estimated based on mutual constraints. The measured results confirm the capability. In addition, the factors of coherent sampling, noise bandwidth, and comparator threshold that influence the performance of the proposed technique are simulated and discussed in detail.
- 1 May 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (5)
Weak signal detection technique based on Durbin–Watson test and one-bit sampling
Correlation-based detection techniques are widely used in the weak periodic signal detection field. Traditionally, they are based on extracting the correlation of a weak signal from noise. Considering the impact of a weak signal on the randomness of background noise, this article takes the opposite approach and proposes a weak signal detection technique based on the Durbin–Watson (DW) test and one-bit sampling, detecting the weak signal due to the extent to which the randomness of noise is affected. The randomness of noise is analyzed through the DW test, which is a method for detecting the randomness of data sequences through first-order autocorrelation. One-bit sampling is adopted to reduce the complexity of the sampling circuit and data processing algorithm. The effectiveness of the DW test in the situation of one-bit sampling is demonstrated through simulation and analysis. Simulation results show that the proposed technique is capable of detecting weak sinusoidal and square-wave signals with a signal-to-noise ratio (SNR) above −30 dB, and the frequency or SNR of a weak signal can be further estimated based on mutual constraints. The measured results confirm the capability. In addition, the factors of coherent sampling, noise bandwidth, and comparator threshold that influence the performance of the proposed technique are simulated and discussed in detail.
- 1 February 2021
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 92 (2) , 024703
A field programmable gate array based high speed real-time weak periodic signal detection technique
The detection of a high repetition rate weak signal is studied in this paper. Owing to the characteristics of the signal of interest, both high speed analog-to-digital converter (ADC) and low computational complexity data processing techniques are required for high speed real-time weak signal detection. In this paper, a novel field programmable gate array (FPGA) based high speed real-time periodic weak signal detection technique is presented. Cascaded comparators outside the FPGA and cascaded flip flops in the FPGA are used to implement a one-bit ADC, which performs quantization first followed by sampling. Based on this novel design, a time-interleaved structure with several sub-channels is further proposed to significantly improve the sampling rate of the one-bit ADC, which does not require calibration for offset, gain, and sample-time mismatches between sub-channels. Each sub-channel has a long-time coherent integration structure to coherently integrate the sampled one-bit data. A full layer clearance mechanism that only operates on specific bits of the integrated sums is proposed to overcome the influence of a noise baseline drift on the weak signal detection. Compared with the traditional adaptive threshold, this mechanism has a significantly lower computational complexity. A prototype with three sub-channels performing 1.5 Gs/s sampling is implemented to verify the proposed technique. The results obtained confirm its high sampling rate and noise baseline drift tolerance in weak signal detection.
- 1 February 2021
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 92 (2) , 024703
A field programmable gate array based high speed real-time weak periodic signal detection technique
The detection of a high repetition rate weak signal is studied in this paper. Owing to the characteristics of the signal of interest, both high speed analog-to-digital converter (ADC) and low computational complexity data processing techniques are required for high speed real-time weak signal detection. In this paper, a novel field programmable gate array (FPGA) based high speed real-time periodic weak signal detection technique is presented. Cascaded comparators outside the FPGA and cascaded flip flops in the FPGA are used to implement a one-bit ADC, which performs quantization first followed by sampling. Based on this novel design, a time-interleaved structure with several sub-channels is further proposed to significantly improve the sampling rate of the one-bit ADC, which does not require calibration for offset, gain, and sample-time mismatches between sub-channels. Each sub-channel has a long-time coherent integration structure to coherently integrate the sampled one-bit data. A full layer clearance mechanism that only operates on specific bits of the integrated sums is proposed to overcome the influence of a noise baseline drift on the weak signal detection. Compared with the traditional adaptive threshold, this mechanism has a significantly lower computational complexity. A prototype with three sub-channels performing 1.5 Gs/s sampling is implemented to verify the proposed technique. The results obtained confirm its high sampling rate and noise baseline drift tolerance in weak signal detection.
- 24 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 66 (8) , 2005-2010
Development of a Time-of-Flight Electronics System for Neutron Beam Profiling at CSNS-WNS
A 256-channel time-of-flight electronics system has been developed for a facility called “Back-n WNS” in China Spallation Neutron Source (CSNS). This paper presents the structure and performance of the electronics system and test results at CSNS-WNS. A piece of lithium glass scintillator, coupled with a 256-channel multi-anode photomultiplier tube, is placed at the center of the neutron beam line as the detector. A 256-channel readout electronics system, including 1 front-end board (FEB), 4 time-to-digital converter (TDC) cards and 1 clock distribution module (CDM), measures the arrival time of each signal from the detector. Signals are sent to FEB from the detector through 15 cm cables and discriminated on FEB. FEB drives differential signals over 2 m cables to the TDC cards. Each TDC card has 64 channels, using an FPGA to measure the arrival time of each signal. The CDM supplies clock signals to the TDC cards to make them work synchronously. The TDC cards and CDM are housed in one PCI eXtensions for Instrumentation chassis. The TDC cards achieve a timing precision of 3.5 ns. The electronics system meets the requirement of the experiment and is currently being used in CSNS.
- 24 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 66 (8) , 2005-2010
Development of a Time-of-Flight Electronics System for Neutron Beam Profiling at CSNS-WNS
A 256-channel time-of-flight electronics system has been developed for a facility called “Back-n WNS” in China Spallation Neutron Source (CSNS). This paper presents the structure and performance of the electronics system and test results at CSNS-WNS. A piece of lithium glass scintillator, coupled with a 256-channel multi-anode photomultiplier tube, is placed at the center of the neutron beam line as the detector. A 256-channel readout electronics system, including 1 front-end board (FEB), 4 time-to-digital converter (TDC) cards and 1 clock distribution module (CDM), measures the arrival time of each signal from the detector. Signals are sent to FEB from the detector through 15 cm cables and discriminated on FEB. FEB drives differential signals over 2 m cables to the TDC cards. Each TDC card has 64 channels, using an FPGA to measure the arrival time of each signal. The CDM supplies clock signals to the TDC cards to make them work synchronously. The TDC cards and CDM are housed in one PCI eXtensions for Instrumentation chassis. The TDC cards achieve a timing precision of 3.5 ns. The electronics system meets the requirement of the experiment and is currently being used in CSNS.
- 31 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 65 (12) , 2892-2900
An 8-Gs/s 12-Bit TIADC System With Real-Time Broadband Mismatch Error Correction
High sampling speed can be achieved using multiple Analog-to-Digital Converters (ADCs) based on the Time-Interleaving A/D Conversion (TIADC) technique. Various types of methods were proposed to correct the mismatch errors among parallel ADC channels in TIADC systems, which would deteriorate the system performance. Traditional correction methods based on digital signal processing have good performance, however often only for input signals limited in a narrow frequency band. In this paper, we present our recent work on design of an 8-Gsps 12-bit TIADC system and implementation of real-time mismatch correction algorithms in FPGA devices, over a broad band of input signal frequencies. Tests were also conducted to evaluate the systems performance, and the results indicate that the Effective Number of Bits (ENOB) is enhanced to be better than 8.5 bits (<800 MHz) and 8 bits from 800 MHz to 1.6 GHz after correction, almost the same with that of the ADC chip employed.
- 31 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 65 (12) , 2892-2900
An 8-Gs/s 12-Bit TIADC System With Real-Time Broadband Mismatch Error Correction
High sampling speed can be achieved using multiple Analog-to-Digital Converters (ADCs) based on the Time-Interleaving A/D Conversion (TIADC) technique. Various types of methods were proposed to correct the mismatch errors among parallel ADC channels in TIADC systems, which would deteriorate the system performance. Traditional correction methods based on digital signal processing have good performance, however often only for input signals limited in a narrow frequency band. In this paper, we present our recent work on design of an 8-Gsps 12-bit TIADC system and implementation of real-time mismatch correction algorithms in FPGA devices, over a broad band of input signal frequencies. Tests were also conducted to evaluate the systems performance, and the results indicate that the Effective Number of Bits (ENOB) is enhanced to be better than 8.5 bits (<800 MHz) and 8 bits from 800 MHz to 1.6 GHz after correction, almost the same with that of the ADC chip employed.
- 8 August 2018
- Published by Springer Nature in Springer Proceedings in Physics
- p. 190-194
Design of a Data Acquisition Module Based on PXI for Waveform Digitization
- 8 August 2018
- Published by Springer Nature in Springer Proceedings in Physics
- p. 190-194
Design of a Data Acquisition Module Based on PXI for Waveform Digitization