Betty Lemaire-Semail
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Betty Lemaire-Semail has a total of 203 co-authors. Here are the top co-authors by number of shared publications:
Michel Amberg
38 shared publicationsFrederic Giraud
Univ. Lille, Centrale Lille, Arts et Métiers Paris Tech, HEI, EA 2697 - L2EP - Laboratoire d'Electrotechnique et d'Electronique de Puissance, F-59000 Lille, France
23 shared publications- Alain Bouscayrol
Universit de Lille, Arts et Mtiers Institute of Technology, Centrale Lille, Junia, ULR 2697 - L2EP, Lille, France
21 shared publications - Frederic Giraud
University of Lille, Villeneuve d'Ascq, France
21 shared publications Christophe Giraud-Audine
19 shared publicationsFrédéric Giraud
15 shared publications
Latest Publications
- 3 November 2024
- Published by Springer Nature
- p. 293-304
Vibrotactile Cues with Net Lateral Forces Resulting from a Travelling Wave
- 3 November 2024
- Published by Springer Nature
- p. 293-304
Vibrotactile Cues with Net Lateral Forces Resulting from a Travelling Wave
- 4 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 4145-4156
Energy Savings of a Four-Drive Electric Bus With Two Cascaded Smart Integrated Drives on Each Axle
Multi-drive systems are explored as a replacement for single-drive setups in automotive applications. By allowing the selection of one or several drives based on the vehicle operation, a reduction in energy consumption is expected. This paper proposes a 4-drive traction topology for an urban electric bus, featuring two smart integrated drives in cascade on both driven axles. A single-drive-based electric bus with a validated model serves as a reference. The 4-drive system is then incorporated into this e-bus. Energetic macroscopic representation is employed to organize the model and control both bus topologies. An optimal energy management strategy is devised to minimize energy consumption. The 4-drive electric bus achieves a reduction in energy consumption of up to 32% for various urban bus driving cycles. This energy saving is attributed to increased braking energy recovery and an optimal distribution of electric drive torques. A sensitivity analysis on mass variation indicates that the proposed system remains efficient for e-bus applications, even with an increase in mass and volume.
- 4 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 4145-4156
Energy Savings of a Four-Drive Electric Bus With Two Cascaded Smart Integrated Drives on Each Axle
Multi-drive systems are explored as a replacement for single-drive setups in automotive applications. By allowing the selection of one or several drives based on the vehicle operation, a reduction in energy consumption is expected. This paper proposes a 4-drive traction topology for an urban electric bus, featuring two smart integrated drives in cascade on both driven axles. A single-drive-based electric bus with a validated model serves as a reference. The 4-drive system is then incorporated into this e-bus. Energetic macroscopic representation is employed to organize the model and control both bus topologies. An optimal energy management strategy is devised to minimize energy consumption. The 4-drive electric bus achieves a reduction in energy consumption of up to 32% for various urban bus driving cycles. This energy saving is attributed to increased braking energy recovery and an optimal distribution of electric drive torques. A sensitivity analysis on mass variation indicates that the proposed system remains efficient for e-bus applications, even with an increase in mass and volume.
- 29 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (4) , 4610-4620
A Flexible Cloud-Based HIL Testing of Batteries for Various Electrified Vehicles
Power Hardware-In-the-loop (HIL) testing is increasing in the automotive industry for testing subsystems for new vehicles. Usually, the test is located in a unique place (stand-alone (local) HIL). The key-points for a vehicle manufacturer and subsystems suppliers are time and confidentiality. Using the cloud is a way to satisfy the both. Cloud model sharing is developed to spare time and cloud-based real-time simulation limits the access to the models to only certain variables. In this paper, a cloud-based power HIL testing is proposed using a cloud of vehicle models. The Energetic Macroscopic Representation (EMR) formalism is used to organize all the models. It facilitates the interconnections between the simulated and power tested subsystems. Two new batteries are experimentally tested, one for an electric vehicle, the other one for a plug-in hybrid vehicle. The same cloud is used and the power test facilities are located in two different locations. This shows the flexibility of the method.
- 29 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (4) , 4610-4620
A Flexible Cloud-Based HIL Testing of Batteries for Various Electrified Vehicles
Power Hardware-In-the-loop (HIL) testing is increasing in the automotive industry for testing subsystems for new vehicles. Usually, the test is located in a unique place (stand-alone (local) HIL). The key-points for a vehicle manufacturer and subsystems suppliers are time and confidentiality. Using the cloud is a way to satisfy the both. Cloud model sharing is developed to spare time and cloud-based real-time simulation limits the access to the models to only certain variables. In this paper, a cloud-based power HIL testing is proposed using a cloud of vehicle models. The Energetic Macroscopic Representation (EMR) formalism is used to organize all the models. It facilitates the interconnections between the simulated and power tested subsystems. Two new batteries are experimentally tested, one for an electric vehicle, the other one for a plug-in hybrid vehicle. The same cloud is used and the power test facilities are located in two different locations. This shows the flexibility of the method.
- 24 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 16 (4) , 491-496
Temporal Detection Threshold of Audio-Tactile Delays With Virtual Button
Synchronization of audio-tactile stimuli represents a key feature of multisensory interactions. However, information on stimuli synchronization remains scarce, especially with virtual buttons. This work used a click sensation produced with traveling waves and auditory stimulus (a bip-like sound) related to a virtual click for a psychological experiment. Participants accomplish a click gesture and judge if the two stimuli were synchronous or asynchronous. Delay injection was performed on the audio (haptic first) or the click (audio first). In both sessions, one stimulus follows the other with a delay ranging from $0-700\; ms$ . We use weighted and transformed 3-up/1-down staircase procedures to estimate people's sensitivity. We found a threshold of $179 \,\mathrm{ms}$ and $451 \,\mathrm{ms}$ for the auditory first and haptic first conditions, respectively. Statistical analysis revealed a significant effect between the two stimuli' order for threshold. Participants' acceptable asynchrony decreased when the delay was on the haptic rather than on the audio. This effect could be due to the natural experience in which the stimuli tend to be first tactile and then sonorous rather than the other way around. Our findings will help designers to create multimodal virtual buttons by managing audio-tactile temporal synchronization.
- 24 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 16 (4) , 491-496
Temporal Detection Threshold of Audio-Tactile Delays With Virtual Button
Synchronization of audio-tactile stimuli represents a key feature of multisensory interactions. However, information on stimuli synchronization remains scarce, especially with virtual buttons. This work used a click sensation produced with traveling waves and auditory stimulus (a bip-like sound) related to a virtual click for a psychological experiment. Participants accomplish a click gesture and judge if the two stimuli were synchronous or asynchronous. Delay injection was performed on the audio (haptic first) or the click (audio first). In both sessions, one stimulus follows the other with a delay ranging from $0-700\; ms$ . We use weighted and transformed 3-up/1-down staircase procedures to estimate people's sensitivity. We found a threshold of $179 \,\mathrm{ms}$ and $451 \,\mathrm{ms}$ for the auditory first and haptic first conditions, respectively. Statistical analysis revealed a significant effect between the two stimuli' order for threshold. Participants' acceptable asynchrony decreased when the delay was on the haptic rather than on the audio. This effect could be due to the natural experience in which the stimuli tend to be first tactile and then sonorous rather than the other way around. Our findings will help designers to create multimodal virtual buttons by managing audio-tactile temporal synchronization.
- Open Access
- 3 April 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-12
Cross-modal interaction of stereoscopy, surface deformation and tactile feedback on the perception of texture roughness in an active touch condition
Research has shown that interaction with tactile surfaces can benefit from the addition of haptic feedback. The perception of this feedback is influenced by other modalities, visual and auditory, making it possible to reinforce or enrich it. However, the effect of visual depth cues, such as stereoscopic rendering and surface deformation, on the tactile perception of textures has not been studied yet, especially in an active touch condition. In this paper, we investigate the perceptual interaction between stereoscopy, surface deformation, and haptic feedback in the condition of active touch implemented using friction modulation based on ultrasonic vibrations. The experimental study is based on a Visual-Tactile exploration of a virtual texture. Our objective is to understand the interaction of one modality over the other for roughness and depth perception. Participants were asked to make visual and tactile texture roughness judgments and to estimate the depth of deformation of the texture below their fingers. Our results suggest that: 1) perceived tactile roughness can be modified by adding stereoscopic rendering and/or visual surface deformation but only for smooth tactile textures, 2) perceived visual roughness can be modified by increasing the tactile roughness, 3)the overall roughness (Visual + Tactile) is mainly impacted by the tactile perception.
- 3 April 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-12
Open AccessCross-modal interaction of stereoscopy, surface deformation and tactile feedback on the perception of texture roughness in an active touch condition
Research has shown that interaction with tactile surfaces can benefit from the addition of haptic feedback. The perception of this feedback is influenced by other modalities, visual and auditory, making it possible to reinforce or enrich it. However, the effect of visual depth cues, such as stereoscopic rendering and surface deformation, on the tactile perception of textures has not been studied yet, especially in an active touch condition. In this paper, we investigate the perceptual interaction between stereoscopy, surface deformation, and haptic feedback in the condition of active touch implemented using friction modulation based on ultrasonic vibrations. The experimental study is based on a Visual-Tactile exploration of a virtual texture. Our objective is to understand the interaction of one modality over the other for roughness and depth perception. Participants were asked to make visual and tactile texture roughness judgments and to estimate the depth of deformation of the texture below their fingers. Our results suggest that: 1) perceived tactile roughness can be modified by adding stereoscopic rendering and/or visual surface deformation but only for smooth tactile textures, 2) perceived visual roughness can be modified by increasing the tactile roughness, 3)the overall roughness (Visual + Tactile) is mainly impacted by the tactile perception.
- 1 March 2022
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 167
Closed loop control of vibration field transient: Application to wave focusing
- 1 March 2022
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 167
Closed loop control of vibration field transient: Application to wave focusing
- 4 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 15 (1) , 8-13
Mechanisms of Friction Reduction in Longitudinal Ultrasonic Surface Haptic Devices With Non-Collinear Vibrations and Finger Displacement
Friction reduction using ultrasonic longitudinal surface vibration can modify the user perception of the touched surface and induce the perception of textured materials. In the current paper, the mechanisms of friction reduction using longitudinal vibration are analyzed at different finger exploration velocities and directions over a plate. The development of a non-Coulombic adhesion theory based on experimental results is evaluated as a possible explanation for friction reduction with vibrations that are non-collinear with the finger displacement. Comparison with experimental data shows that the model adequately describes the reduction in friction, although it is less accurate for low finger velocities and depends on motion direction.
- 4 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 15 (1) , 8-13
Mechanisms of Friction Reduction in Longitudinal Ultrasonic Surface Haptic Devices With Non-Collinear Vibrations and Finger Displacement
Friction reduction using ultrasonic longitudinal surface vibration can modify the user perception of the touched surface and induce the perception of textured materials. In the current paper, the mechanisms of friction reduction using longitudinal vibration are analyzed at different finger exploration velocities and directions over a plate. The development of a non-Coulombic adhesion theory based on experimental results is evaluated as a possible explanation for friction reduction with vibrations that are non-collinear with the finger displacement. Comparison with experimental data shows that the model adequately describes the reduction in friction, although it is less accurate for low finger velocities and depends on motion direction.
- 18 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 14 (3) , 551-563
PCA Model of Fundamental Acoustic Finger Force for Out-of-Plane Ultrasonic Vibration and its Correlation with Friction Reduction
When a finger touches an ultrasonic vibrating plate, a non-sinusoidal contact force is produced. This force is called acoustic finger force. In a setup where closed-loop control is performed on the vibration amplitude, a component of the acoustic finger force can be measured at the fundamental vibration frequency of the plate. This calculation is obtained from the measurement of the variation of the controller voltage between the no-load case and when a finger is present. This calculation is made for a group of twelve participants. From these results a PCA (Principal Component Analysis) model is created. This model permits estimation of the acoustic finger force response of a participant at any vibration amplitude, based on a one or two point measurement. Finally, a linear relation between the PCA coefficients and the friction reduction is proposed. The objective of this relation would be to ultimately provide the means to create an amplitude reference calibration based on the desired friction reduction level, and thus be able to produce a standardized tactile feedback for each user, despite the biomechanical differences in finger pad properties between subjects.
- 18 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 14 (3) , 551-563
PCA Model of Fundamental Acoustic Finger Force for Out-of-Plane Ultrasonic Vibration and its Correlation with Friction Reduction
When a finger touches an ultrasonic vibrating plate, a non-sinusoidal contact force is produced. This force is called acoustic finger force. In a setup where closed-loop control is performed on the vibration amplitude, a component of the acoustic finger force can be measured at the fundamental vibration frequency of the plate. This calculation is obtained from the measurement of the variation of the controller voltage between the no-load case and when a finger is present. This calculation is made for a group of twelve participants. From these results a PCA (Principal Component Analysis) model is created. This model permits estimation of the acoustic finger force response of a participant at any vibration amplitude, based on a one or two point measurement. Finally, a linear relation between the PCA coefficients and the friction reduction is proposed. The objective of this relation would be to ultimately provide the means to create an amplitude reference calibration based on the desired friction reduction level, and thus be able to produce a standardized tactile feedback for each user, despite the biomechanical differences in finger pad properties between subjects.
- 1 April 2019
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 158, 120-129
Influence of a CVT on the fuel consumption of a parallel medium-duty electric hybrid truck
- 1 April 2019
- Published by Elsevier in Mathematics and Computers in Simulation
- Vol. 158, 120-129
Influence of a CVT on the fuel consumption of a parallel medium-duty electric hybrid truck
- 22 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 12 (2) , 179-188
The Perception of Ultrasonic Square Reductions of Friction With Variable Sharpness and Duration
The human perception of square ultrasonic modulation of the finger-surface friction was investigated during active tactile exploration by using short frictional cues of varying duration and sharpness. In a first experiment, we asked participants to discriminate the transition time and duration of short square ultrasonic reductions of friction. They proved very sensitive to discriminate millisecond differences in these two parameters with the average psychophysical thresholds being 2.3-2.4 ms for both parameters. A second experiment focused on the perception of square friction reductions with variable transition times and durations. We found that for durations of the stimulation larger than 90 ms, participants often perceived three or four edges when only two stimulations were presented while they consistently felt two edges for signals shorter than 50 ms. A subsequent analysis of the contact forces induced by these ultrasonic stimulations during slow and fast active exploration showed that two identical consecutive ultrasonic pulses can induce significantly different frictional dynamics especially during fast motion of the finger. These results confirm the human sensitivity to transient frictional cues and suggest that the human perception of square reductions of friction can depend on their sharpness and duration as well as on the speed of exploration.
- 22 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Haptics
- Vol. 12 (2) , 179-188
The Perception of Ultrasonic Square Reductions of Friction With Variable Sharpness and Duration
The human perception of square ultrasonic modulation of the finger-surface friction was investigated during active tactile exploration by using short frictional cues of varying duration and sharpness. In a first experiment, we asked participants to discriminate the transition time and duration of short square ultrasonic reductions of friction. They proved very sensitive to discriminate millisecond differences in these two parameters with the average psychophysical thresholds being 2.3-2.4 ms for both parameters. A second experiment focused on the perception of square friction reductions with variable transition times and durations. We found that for durations of the stimulation larger than 90 ms, participants often perceived three or four edges when only two stimulations were presented while they consistently felt two edges for signals shorter than 50 ms. A subsequent analysis of the contact forces induced by these ultrasonic stimulations during slow and fast active exploration showed that two identical consecutive ultrasonic pulses can induce significantly different frictional dynamics especially during fast motion of the finger. These results confirm the human sensitivity to transient frictional cues and suggest that the human perception of square reductions of friction can depend on their sharpness and duration as well as on the speed of exploration.