Yiwei Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yiwei Ren has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Xiao Wang
Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing 400714, China
4 shared publications Jing Li
Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing, China
3 shared publicationsYuntao Zhao
Chinese Academy of Sciences
3 shared publications- De-Sheng Pei
School of Public Health, Chongqing Medical University, Chongqing 400016, China
2 shared publications Enling Tian
Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing, China
2 shared publications- Enling Tian
Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences, Chongqing 400714, China
2 shared publications
Latest Publications
- Open Access
Electrospun Graphene Oxide/Poly(m-phenylene isophthalamide) Composite Nanofiber Membranes for High Performance
Due to its distinctive two-dimensional structure and high specific surface area, graphene oxide (GO) is expected to be a very promising material to be used for membrane separation. Not only can it improve the mechanical strength, surface wettability, and thermal stability of the membrane, but it can also improve the filtration performance and shelf life of the polymer membrane. Graphene oxide/poly(meta-phenylene isophthalamide) (GO/PMIA) nanofiber membranes were prepared by means of an electrospinning technique. The effects of adding different amounts of GO on the PMIA nanofiber membranes were studied. The results indicated that the GO had a strong affinity with the PMIA matrix by forming hydrogen bonds. The composite nanofiber membranes exhibited better filtration and thermostability performance than those of the pristine membrane. As the loading amount of GO was 1.0 wt%, the air filtration efficiency of the composite nanofiber membrane was 97.79%, the pressure drop was 85.45 Pa and the glass transition temperature was 299.8 °C.
Open AccessElectrospun Graphene Oxide/Poly(m-phenylene isophthalamide) Composite Nanofiber Membranes for High Performance
Due to its distinctive two-dimensional structure and high specific surface area, graphene oxide (GO) is expected to be a very promising material to be used for membrane separation. Not only can it improve the mechanical strength, surface wettability, and thermal stability of the membrane, but it can also improve the filtration performance and shelf life of the polymer membrane. Graphene oxide/poly(meta-phenylene isophthalamide) (GO/PMIA) nanofiber membranes were prepared by means of an electrospinning technique. The effects of adding different amounts of GO on the PMIA nanofiber membranes were studied. The results indicated that the GO had a strong affinity with the PMIA matrix by forming hydrogen bonds. The composite nanofiber membranes exhibited better filtration and thermostability performance than those of the pristine membrane. As the loading amount of GO was 1.0 wt%, the air filtration efficiency of the composite nanofiber membrane was 97.79%, the pressure drop was 85.45 Pa and the glass transition temperature was 299.8 °C.
- 18 December 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 58 (2) , 897-907
Preparation and Characterization of Thin-Film Nanocomposite Membrane with High Flux and Antibacterial Performance for Forward Osmosis
- 18 December 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 58 (2) , 897-907
Preparation and Characterization of Thin-Film Nanocomposite Membrane with High Flux and Antibacterial Performance for Forward Osmosis
- 17 August 2018
- Published by Springer Nature in Journal of Polymer Research
- Vol. 25 (9) , 199
Fabrication of fullerenol-incorporated thin-film nanocomposite forward osmosis membranes for improved desalination performances
- 17 August 2018
- Published by Springer Nature in Journal of Polymer Research
- Vol. 25 (9) , 199
Fabrication of fullerenol-incorporated thin-film nanocomposite forward osmosis membranes for improved desalination performances
- 18 June 2018
- Published by SAGE Publications in High Performance Polymers
- Vol. 31 (4) , 438-448
High-performance polyimide nanofiber membranes prepared by electrospinning
Polyimide (PI) nanofiber membranes were successfully prepared from a PI/N-methyl-2-pyrrolidone (NMP) solution via electrospinning. This technique simply and facilely produced efficient high-performance PI fibers. The morphology, surface wettability, thermal stability, mechanical properties, and filtration performance of the as-prepared PI nanofiber membranes were characterized in detail. The membranes exhibited smooth and hydrophobic surfaces. The nanofibers were well distributed in the membranes with fiber diameters in the range of 140–400 nm. All the PI nanofiber membranes showed excellent thermostability, and their initial decomposition temperature ( Td) and heat resistance temperature ( THRI) exceeded 544.4°C and 198.8°C, respectively. The PI nanofiber membranes also possessed reasonable mechanical properties with a tensile strength and a Young’s modulus reaching 10.5 and 927.6 MPa, respectively. Regarding the filtration performance, the developed nanofiber membranes achieved the best filtration efficiency of 90.4%. Such electrospun PI nanofiber membranes can be a promising candidate for hot gas filtration.
- 18 June 2018
- Published by SAGE Publications in High Performance Polymers
- Vol. 31 (4) , 438-448
High-performance polyimide nanofiber membranes prepared by electrospinning
Polyimide (PI) nanofiber membranes were successfully prepared from a PI/N-methyl-2-pyrrolidone (NMP) solution via electrospinning. This technique simply and facilely produced efficient high-performance PI fibers. The morphology, surface wettability, thermal stability, mechanical properties, and filtration performance of the as-prepared PI nanofiber membranes were characterized in detail. The membranes exhibited smooth and hydrophobic surfaces. The nanofibers were well distributed in the membranes with fiber diameters in the range of 140–400 nm. All the PI nanofiber membranes showed excellent thermostability, and their initial decomposition temperature ( Td) and heat resistance temperature ( THRI) exceeded 544.4°C and 198.8°C, respectively. The PI nanofiber membranes also possessed reasonable mechanical properties with a tensile strength and a Young’s modulus reaching 10.5 and 927.6 MPa, respectively. Regarding the filtration performance, the developed nanofiber membranes achieved the best filtration efficiency of 90.4%. Such electrospun PI nanofiber membranes can be a promising candidate for hot gas filtration.
- 21 May 2018
- Published by Wiley in Advanced Materials Interfaces
- Vol. 5 (15)
Graphene Oxide‐Based Polymeric Membranes for Water Treatment
Membrane technologies for water treatment and desalination are increasingly developed and utilized to address the global challenges of water security and supply. Membrane‐based separations can produce water with desirable qualities from a wide range of water sources, such as groundwater, seawater, brackish water, and wastewater. However, the membranes, which are typically made from polymers, are still restricted by their inherent limitations, including a permeability/selectivity trade‐off and a high fouling propensity. Functionalized graphene (i.e., graphene oxide and its functionalized derivates) is regarded as a very promising nanomaterial for overcoming these limitations owing to its superior hydrophilicity, mechanical stability, bacteriostasis, and biocidal properties. The addition of a small amount of this nanomaterial (normally less 1 wt% based on the weight of polymer) into polymeric membranes significantly improves their physicochemical properties and provides new functionalities. In this review, the recent advances in the preparation of functionalized graphene and its integration into polymer membranes for water treatment are summarized. The influences of functionalized graphene on the separation performance, antifouling ability, chlorine resistance, and mechanical properties of membranes are revealed. Current challenges and future perspectives in the development of high‐performance functionalized graphene–polymer membranes are also discussed.
- 21 May 2018
- Published by Wiley in Advanced Materials Interfaces
- Vol. 5 (15)
Graphene Oxide‐Based Polymeric Membranes for Water Treatment
Membrane technologies for water treatment and desalination are increasingly developed and utilized to address the global challenges of water security and supply. Membrane‐based separations can produce water with desirable qualities from a wide range of water sources, such as groundwater, seawater, brackish water, and wastewater. However, the membranes, which are typically made from polymers, are still restricted by their inherent limitations, including a permeability/selectivity trade‐off and a high fouling propensity. Functionalized graphene (i.e., graphene oxide and its functionalized derivates) is regarded as a very promising nanomaterial for overcoming these limitations owing to its superior hydrophilicity, mechanical stability, bacteriostasis, and biocidal properties. The addition of a small amount of this nanomaterial (normally less 1 wt% based on the weight of polymer) into polymeric membranes significantly improves their physicochemical properties and provides new functionalities. In this review, the recent advances in the preparation of functionalized graphene and its integration into polymer membranes for water treatment are summarized. The influences of functionalized graphene on the separation performance, antifouling ability, chlorine resistance, and mechanical properties of membranes are revealed. Current challenges and future perspectives in the development of high‐performance functionalized graphene–polymer membranes are also discussed.
- 9 January 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (3) , 2918-2928
Mesh-Embedded Polysulfone/Sulfonated Polysulfone Supported Thin Film Composite Membranes for Forward Osmosis
In this work, mesh-embedded polysulfone (PSU)/sulfonated polysulfone (sPSU) supported thin film composite (TFC) membranes were developed for forward osmosis (FO). The robust mesh integrated in PSU/sPSU sublayer imparts impressive mechanical durability. The blending of hydrophilic sPSU in PSU sublayer affects the hydrophilicity, porosity, pore structure and pore size of mesh-embedded PSU/sPSU substrates, and the total thickness, crosslinking degree and roughness of the corresponding TFC-FO membrane active layers. An appropriate incorporation of sPSU not only significantly decreases the structural parameter, S of the mesh-embedded substrate to 220μm which is the lowest reported value for fabric backed FO membrane, but also optimizes the permselectivity of the formed active layer. Regarding the osmosis performance, TFC membranes with sPSU modified substrates gain a higher water flux (Jw) while keeping the specific reverse salt flux (Js/Jw) low. The optimal TFC-FO membrane has a Jw of 31.76LMH with Js/Jw of 0.19g/L in FO mode when using deionized water feed and 1M NaCl draw solution. This paper is practical for developing TFC-FO membrane on hydrophilic support membrane materials.
- 9 January 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (3) , 2918-2928
Mesh-Embedded Polysulfone/Sulfonated Polysulfone Supported Thin Film Composite Membranes for Forward Osmosis
In this work, mesh-embedded polysulfone (PSU)/sulfonated polysulfone (sPSU) supported thin film composite (TFC) membranes were developed for forward osmosis (FO). The robust mesh integrated in PSU/sPSU sublayer imparts impressive mechanical durability. The blending of hydrophilic sPSU in PSU sublayer affects the hydrophilicity, porosity, pore structure and pore size of mesh-embedded PSU/sPSU substrates, and the total thickness, crosslinking degree and roughness of the corresponding TFC-FO membrane active layers. An appropriate incorporation of sPSU not only significantly decreases the structural parameter, S of the mesh-embedded substrate to 220μm which is the lowest reported value for fabric backed FO membrane, but also optimizes the permselectivity of the formed active layer. Regarding the osmosis performance, TFC membranes with sPSU modified substrates gain a higher water flux (Jw) while keeping the specific reverse salt flux (Js/Jw) low. The optimal TFC-FO membrane has a Jw of 31.76LMH with Js/Jw of 0.19g/L in FO mode when using deionized water feed and 1M NaCl draw solution. This paper is practical for developing TFC-FO membrane on hydrophilic support membrane materials.
- 1 February 2017
- Published by Elsevier in Chemosphere
- Vol. 168, 112-121
A novel forward osmosis system in landfill leachate treatment for removing polycyclic aromatic hydrocarbons and for direct fertigation
- 1 February 2017
- Published by Elsevier in Chemosphere
- Vol. 168, 112-121
A novel forward osmosis system in landfill leachate treatment for removing polycyclic aromatic hydrocarbons and for direct fertigation