VMVyacheslav M. Matyunin

Vyacheslav M. Matyunin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vyacheslav M. Matyunin has a total of 111 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Influence of the Portevin-Le Chatelier Effect on the Resistance of Aluminum Alloy AMg6 to Static, Dynamic and Cyclic Loads

    by V. M. Matyunin, A. Yu. Marchenkov, M. A. Karimbekov, R. Yu. Agafonov, N. O. Tsvetkova, A. A. Pan’KIna

    The influence of the Portevin-Le Chatelier effect on the mechanical properties of AMg6 aluminum alloy specimens under static, dynamic, and cyclic loading was studied. It was found that this effect has little effect on the yield strength, tensile strength, and elongation determined under static tension at a strain rate of 5 mm/min. However, it significantly reduces impact toughness and its components-the work of crack initiation and propagation-and also reduces the number of cycles to complete failure under cyclic loading of the specimen at the same maximum cycle stress.

  • INFLUENCE OF THE PORTEVIN-LE CHATELIER EFFECT ON THE RESISTANCE OF ALUMINUM ALLOY AMG6 TO STATIC, DYNAMIC AND CYCLIC LOADS

    by V.M. Matyunin, A.YU. Marchenkov, M.A. Karimbekov, R.YU. Agafonov, N.O. Tsvetkova, A.A. Pankina

    The influence of the Portevin-Le Chatelier effect on the mechanical properties of AMg6 aluminum alloy under static, dynamic, and cyclic loading of specimens was studied. It was found that this effect has little impact on the yield strength, temporary resistance and relative elongation determined under static tension of the specimen at a strain rate of 5 mm / min. However, it significantly reduces impact toughness and its components - the energy of crack initiation and propagation - and also reduces the number of cycles to complete failure under cyclic loading of the specimen at the same maximum stress of the cycle.

  • Construction of True Stress–Strain Diagrams for Tension with Determination of Mechanical Properties of Materials from the Results of Instrumented Indentation and Scratching

    by V. M. Matyunin, A. Yu. Marchenkov, P. V. Volkov, M. A. Karimbekov, N. O. Tsvetkova, A. A. Pan’KIna, G. B. Sviridov, A. N. Demidov

    The technique for constructing stress–strain diagrams for structural metal materials in the “true stress–true residual strain” coordinates has been developed up to fracture of samples from parameters of instrumented indentation and scratching. It is proposed that the plastic segment of the tensile test diagram in the region of uniform straining be obtained from the kinetic diagram of indentation by a spherical indenter. The segment of the tensile test diagram in the strain concentration region can be obtained from the scratching diagram. The methodology developed in this study has been approved with positive result for several structural materials (steels of various structural classes and titanium alloys).

  • Properties of True Stress Diagrams in Areas of Necking and Fracture of Materials under Tension

    by V. M. Matyunin, A. Yu. Marchenkov, N. O. Tsvetkova, D. A. Zhgut, A. A. Pankina, G. B. Sviridov

    —Tensile testing of steel samples has been carried out, and loaded and unloaded true stress curves have been plotted. It has been shown that the true stress–true strain curves in the area of necking have the shape of an inclined ascending straight line until fracture. It has been established that the straightness of the diagram is also observed for austenitic steel, in the structure of which martensite is formed under plastic deformation. In contrast to these diagrams, the true stress–conditional relative area reduction curves exhibit a straightness violation with the upward deviation at the final stage of necking. The true ultimate tensile stresses calculated using the Davidenkov correction decrease and approach the straight line of the diagram. Although the unloaded values of true stresses and true strains exceed the loaded values at the same tensile force, they fit on the same curves at different stages of the material deformation. The Kerber rule can be applied to the true stress–conditional relative area reduction curves if a sufficiently long rectilinear curve section is clearly identified after the true ultimate tensile stress has been attained, in order to extrapolate this section to the true relative area reduction equal to unity. The Kerber rule is inapplicable to the true stress–true strain curves, despite their straightness in the area of necking, because of the uncertainty in calculating the true logarithmic strain at the unit true relative area reduction. At the same time, the presence of a linear section in these curves over the entire area of necking greatly simplifies the plotting of the entire tensile curve until fracture.


  • Determination of the Crack Initiation and Propagation Energies during Instrumented Indentation of Brittle Materials and Hardening Coatings

    by V. M. Matyunin, A. Yu. Marchenkov, M. P. Petrova, O. S. Zilova, A. A. Pan’KIna, G. B. Sviridov

    The well-known methods of determining the critical stress intensity factor KIc of the surface layers of materials by indentation of a pyramid for the formation of radial cracks propagating from the vertices of an indent are considered. It is noted that the existing methods for estimating the fracture toughness of a material by indentation do not allow one to determine the crack initiation energy. A technique is proposed to determine the specific crack initiation energy and the specific crack propagation energy using the critical points of a pyramid indentation diagram during instrumented indentation. Energy fracture toughness criterion GIc is found to be related to specific crack propagation energy ωp, which is determined using an indentation diagram, for brittle materials and hardening coatings. This finding makes it possible to develop a technique for rapid estimation of critical stress intensity factor KIc using an indentation diagram recorded during instrumented indentation without measuring the geometric parameters of formed cracks and regardless of their type.


  • Influence of the Scale Factor on the Young’s Modulus of Steel Determined by the Tensile Strength of the Specimens

    by V. M. Matyunin, A. Yu. Marchenkov, M. V. Goryachkina, A. Yu. Poroykov, D. A. Zhgut, M. A. Karimbekov, A. A. Pankina

    The modulus of elasticity is considered a fairly stable physicomechanical characteristic of materials, which is little dependent on their composition and structure. Among the factors influencing the modulus of elasticity, temperature and anisotropy are distinguished. Information about the influence of scale factor on the modulus of elasticity is quite limited and sometimes contradictory. The aim of this study is to investigate the influence of the scale factor on the elastic modulus of steel 45 determined by tension geometrically similar specimens with different initial diameters. The specimens were tested on an Instron 8801 universal testing machine at a deformation rate of 0.1 mm/min at room temperature. Elastic deformations during tension were measured using two methods—with the help of a strain gauge and the digital image correlation method. Both methods showed fairly close results when testing specimens of the same diameter. However, the digital image correlation method allowed for measurements of elastic deformations on specimens with small diameters, where it was not possible to attach a strain gauge. A decrease in the modulus of elasticity with an increase in the initial diameter of the specimen was established. Graphical dependences of the modulus of elasticity on the diameter of the specimen and the area of its cross section were obtained. Possible reasons for the decrease in the modulus of elasticity under the influence of the scale factor are outlined. A decrease in specific surface area and specific surface energy, an increase in the deformable volume, and a decrease in the deformation rate at a constant deformation speed are among the main reasons. The decrease in the modulus of elasticity under the influence of the scale factor should be taken into account in strength calculations and when assessing the residual life of parts and structures with relatively large cross sections and wall thicknesses.

  • Investigation of thermal stability of gray bainite phosphorous cast iron for valve seats of internal combustion engines

    by Togliatty State University, D.A. Boldyrev, K.V. Makarenko, Bryansk State Technical University, L.I. Popova

    Выполнено исследование влияния моделирования эксплуатационной температуры (~550 °C) в новой конструкции головки блока цилиндров двигателей внутреннего сгорания (ДВС) легкового автомобиля на термостабильность структуры и твердость отливок типа «седло вставное выпускного клапана» из серого бейнитного фосфористого чугуна (в литом состоянии и отпущенного) специально подобранного химического состава, обеспечивающего получение металлической основы - бейнита - при непрерывном охлаждении без использования изотермической закалки. Показано воздействие одно- и двухкратного отпуска на изменение структуры и твердости чугуна. Установлена неудовлетворительная работоспособность бейнитной структуры для седел клапанов, не обеспечивающая сохранение требуемого уровня твердости.

  • Plotting of diagrams of true stresses and strains under tension with determination of mechanical properties of materials, based on results of instrumental indentation by indentation and scratching

    by National Research University «MPEI», V.M. Matyunin, A.YU. Marchenkov, P.V. Volkov, M.A. Karimbekov, N.O. Tsvetkova, A.A. Pankina, G.B. Sviridov, A.N. Demidov

    Разработана методика построения диаграмм растяжения конструкционных металлических материалов в координатах «истинные напряжения-истинные остаточные деформации» вплоть до разрыва образца по параметрам инструментального индентирования методами вдавливания и царапания. Пластический участок диаграммы растяжения в области равномерной деформации предложено получать по кинетической диаграмме вдавливания сферическим индентором. Участок диаграммы растяжения в области сосредоточенной деформации предложено получать по диаграмме царапания. Разработанная методика опробована с положительным результатом на нескольких конструкционных материалах: сталях различных структурных классов и титановых сплавах.

  • Converting the Instrumented Indentation Diagrams of a Ball Indenter into the Stress–Strain Curves for Metallic Structural Materials

    by V. M. Matyunin, A. Yu. Marchenkov, P. V. Volkov, M. A. Karimbekov, D. A. Zhgut, M. P. Petrova, N. O. Veremeeva

    The available approaches to converting indentation diagrams into stress–strain curves are reviewed. It is noted that most studies on converting the instrumented indentation diagrams of a ball indenter into the stress–strain curves have been carried out within the uniform deformation limits using various computational and experimental approaches, including the finite element method and neural networks. In the authors’ opinion, however, it is reasonable to perform the conversion of one diagram to another using the established relationship between indentation and tension deformations. This makes it possible not only to perform the conversion with a higher accuracy but also to evaluate the mechanical properties under tension from the indentation characteristics. The formulas most frequently used to determine plastic deformation contain a relative indentation diameter as the main parameter. Meanwhile, at the same relative indentation diameter and a constant ratio between the average contact pressure (Meyer hardness) and the true tensile stress, the indentation and tensile strain values can be significantly different owing to different strain hardening abilities of materials. The authors have established a relationship between the true elastoplastic deformation in the tensile tests and the relative depth of an unrecovered indentation obtained with a ball indenter with allowance for the strain hardening parameter determined from the instrumented indentation diagram. On the basis of the established relationship, a technique for converting the instrumented indentation diagram into a stress–strain curve in the uniform deformation region with the determination of the yield strength, tensile strength, and ultimate uniform tension has been developed. The technique has been verified by testing steels and aluminum, magnesium, and titanium alloys with strongly different Young’s moduli, strength characteristics, plasticity, and strain hardening.


  • Effect of the Scale Factor on the Elastic Modulus Determined by Instrumented Indentation

    by V. M. Matyunin, A. Yu. Marchenkov, P. V. Volkov, M. A. Karimbekov, A. A. Pan’KIna

    —The effect of the scale factor on the elastic modulus determined by instrumented indentation in the elastic and elastoplastic regions of indentation diagrams has been studied. A significant increase in the elastic modulus has been established upon transition to micro- and nanoscale indentation. The reasons for the effect of the scale factor on the elastic modulus determined by instrumented indentation are outlined.