Bendix Ketelsen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bendix Ketelsen has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Tobias Vossmeyer
Institute of Physical Chemistry University of Hamburg Hamburg Germany
7 shared publications - Hendrik Schlicke
Leibniz Institute of Polymer Research Dresden 01069 Dresden Germany
4 shared publications - Ying-Chih Liao
Department of Chemical Engineering, National Taiwan University, Taipei 10617, Taiwan
4 shared publications - Shan-Hui Hsu
Institute of Polymer Science and Engineering National Taiwan University Taipei Taiwan
3 shared publications - Shin-Da Wu
Institute of Polymer Science and Engineering National Taiwan University Taipei 10617 Taiwan
3 shared publications Chun-Hao Su
Department of Chemical Engineering , National Taiwan University , Taipei 10617 , Taiwan
2 shared publications
Latest Publications
- Open Access
- 8 May 2023
- Published by Wiley in Small Methods
- Vol. 7 (9) , e2300170
Fabrication of Eco‐Friendly Wearable Strain Sensor Arrays via Facile Contact Printing for Healthcare Applications
Wearable flexible strain sensors with spatial resolution enable the acquisition and analysis of complex actions for noninvasive personalized healthcare applications. To provide secure contact with skin and to avoid environmental pollution after usage, sensors with biocompatibility and biodegradability are highly desirable. Herein, wearable flexible strain sensors composed of crosslinked gold nanoparticle (GNP) thin films as the active conductive layer and transparent biodegradable polyurethane (PU) films as the flexible substrate are developed. The patterned GNP films (micrometer‐ to millimeter‐scale square and rectangle geometry, alphabetic characters, and wave and array patterns) are transferred onto the biodegradable PU film via a facile, clean, rapid and high‐precision contact printing method, without the need of a sacrificial polymer carrier or organic solvents. The GNP‐PU strain sensor with low Young's modulus (≈17.8 MPa) and high stretchability showed good stability and durability (10 000 cycles) as well as degradability (42% weight loss after 17 days at 74 °C in water). The GNP‐PU strain sensor arrays with spatiotemporal strain resolution are applied as wearable eco‐friendly electronics for monitoring subtle physiological signals (e.g., mapping of arterial lines and sensing pulse waveforms) and large‐strain actions (e.g., finger bending).
- 8 May 2023
- Published by Wiley in Small Methods
- Vol. 7 (9) , e2300170
Open AccessFabrication of Eco‐Friendly Wearable Strain Sensor Arrays via Facile Contact Printing for Healthcare Applications
Wearable flexible strain sensors with spatial resolution enable the acquisition and analysis of complex actions for noninvasive personalized healthcare applications. To provide secure contact with skin and to avoid environmental pollution after usage, sensors with biocompatibility and biodegradability are highly desirable. Herein, wearable flexible strain sensors composed of crosslinked gold nanoparticle (GNP) thin films as the active conductive layer and transparent biodegradable polyurethane (PU) films as the flexible substrate are developed. The patterned GNP films (micrometer‐ to millimeter‐scale square and rectangle geometry, alphabetic characters, and wave and array patterns) are transferred onto the biodegradable PU film via a facile, clean, rapid and high‐precision contact printing method, without the need of a sacrificial polymer carrier or organic solvents. The GNP‐PU strain sensor with low Young's modulus (≈17.8 MPa) and high stretchability showed good stability and durability (10 000 cycles) as well as degradability (42% weight loss after 17 days at 74 °C in water). The GNP‐PU strain sensor arrays with spatiotemporal strain resolution are applied as wearable eco‐friendly electronics for monitoring subtle physiological signals (e.g., mapping of arterial lines and sensing pulse waveforms) and large‐strain actions (e.g., finger bending).
- Open Access
- 19 December 2022
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (7)
Nanoparticle‐Based Strain Gauges: Anisotropic Response Characteristics, Multidirectional Strain Sensing, and Novel Approaches to Healthcare Applications
Directional strain sensing is essential for advanced sensor applications in the field of human‐machine interfaces and healthcare. Here, the angle dependent anisotropic strain sensitivity caused by charge carriers percolating through cross‐linked gold nanoparticle (GNP) networks is studied and these versatile materials are used for the fabrication of wearable triaxial pulse and gesture sensors. More specifically, the anisotropic response of 1,9‐nonanedithiol cross‐linked GNP films is separated into geometric and piezoresistive contributions by fitting the measured data with an analytic model. Hereby, piezoresistive coefficients of g11 ∼ 32 and g12 ∼ 21 are extracted, indicating a slightly anisotropic response behavior of the GNP‐based material. To use the material for healthcare applications, arrangements of three GNP transducers are patterned lithographically and fully embedded into a highly flexible silicone polymer (Dragon Skin 30). The new encapsulation method ensures good and robust electrical contacts and enables facile handling and protection from external influences. A facile read‐out with wireless data transmission using off‐the‐shelf electrical components underlines the great potential of these devices for applications as skin‐wearable healthcare sensors.
- 19 December 2022
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (7)
Open AccessNanoparticle‐Based Strain Gauges: Anisotropic Response Characteristics, Multidirectional Strain Sensing, and Novel Approaches to Healthcare Applications
Directional strain sensing is essential for advanced sensor applications in the field of human‐machine interfaces and healthcare. Here, the angle dependent anisotropic strain sensitivity caused by charge carriers percolating through cross‐linked gold nanoparticle (GNP) networks is studied and these versatile materials are used for the fabrication of wearable triaxial pulse and gesture sensors. More specifically, the anisotropic response of 1,9‐nonanedithiol cross‐linked GNP films is separated into geometric and piezoresistive contributions by fitting the measured data with an analytic model. Hereby, piezoresistive coefficients of g11 ∼ 32 and g12 ∼ 21 are extracted, indicating a slightly anisotropic response behavior of the GNP‐based material. To use the material for healthcare applications, arrangements of three GNP transducers are patterned lithographically and fully embedded into a highly flexible silicone polymer (Dragon Skin 30). The new encapsulation method ensures good and robust electrical contacts and enables facile handling and protection from external influences. A facile read‐out with wireless data transmission using off‐the‐shelf electrical components underlines the great potential of these devices for applications as skin‐wearable healthcare sensors.
- Open Access
- 14 December 2020
- Published by MDPI AG in Proceedings
- Vol. 56 (1) , 17
Towards Nanomaterials-Based Biocompatible and Biodegradable Strain Sensors for Healthcare and Medical Applications
Green electronics is an emerging environment-friendly process of the design and manufacture
- 14 December 2020
- Published by MDPI AG in Proceedings
- Vol. 56 (1) , 17
Open AccessTowards Nanomaterials-Based Biocompatible and Biodegradable Strain Sensors for Healthcare and Medical Applications
Green electronics is an emerging environment-friendly process of the design and manufacture
- Open Access
- 14 December 2020
- Published by MDPI AG in Proceedings
- Vol. 56 (1) , 15
Fully Printed Flexible Chemiresistors with Tunable Selectivity Based on Gold Nanoparticle Composites
Functional composite nanomaterials are promising candidates for the fabrication of wearable, flexible chemiresistive sensors which can be used
- 14 December 2020
- Published by MDPI AG in Proceedings
- Vol. 56 (1) , 15
Open AccessFully Printed Flexible Chemiresistors with Tunable Selectivity Based on Gold Nanoparticle Composites
Functional composite nanomaterials are promising candidates for the fabrication of wearable, flexible chemiresistive sensors which can be used
- Open Access
- 18 November 2020
- Published by MDPI AG in Chemosensors
- Vol. 8 (4) , 116
Fully Printed Flexible Chemiresistors with Tunable Selectivity Based on Gold Nanoparticles
This study presents a method for printing flexible chemiresistors comprising thin film transducers based on cross-linked gold nanoparticles (GNPs). First, interdigitated silver paste electrodes are printed onto polyimide (PI) foil via dispenser printing. Second, coatings of GNPs and dithiol/monothiol blends are inkjet-printed onto these electrode structures. 1,9-Nonanedithiol (9DT) is used as cross-linking agent and a variety of monothiols are added to tune the sensors’ chemical selectivity. When dosing these sensors with different analyte vapors (n-octane, toluene, 4-methyl-2-pentanone, 1-butanol, 1-propanol, ethanol, water; concentration range: 25–2000 ppm) they show fully reversible responses with short response and recovery times. The response isotherms follow a first-order Langmuir model, and their initial slopes reveal sensitivities of up to 4.5 ppm−1. Finally, it is demonstrated that arrays of printed sensors can be used to clearly discern analytes of different polarity.- 18 November 2020
- Published by MDPI AG in Chemosensors
- Vol. 8 (4) , 116
Open AccessFully Printed Flexible Chemiresistors with Tunable Selectivity Based on Gold Nanoparticles
This study presents a method for printing flexible chemiresistors comprising thin film transducers based on cross-linked gold nanoparticles (GNPs). First, interdigitated silver paste electrodes are printed onto polyimide (PI) foil via dispenser printing. Second, coatings of GNPs and dithiol/monothiol blends are inkjet-printed onto these electrode structures. 1,9-Nonanedithiol (9DT) is used as cross-linking agent and a variety of monothiols are added to tune the sensors’ chemical selectivity. When dosing these sensors with different analyte vapors (n-octane, toluene, 4-methyl-2-pentanone, 1-butanol, 1-propanol, ethanol, water; concentration range: 25–2000 ppm) they show fully reversible responses with short response and recovery times. The response isotherms follow a first-order Langmuir model, and their initial slopes reveal sensitivities of up to 4.5 ppm−1. Finally, it is demonstrated that arrays of printed sensors can be used to clearly discern analytes of different polarity. - 4 January 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (9) , 3256-3264
Highly Responsive PEG/Gold Nanoparticle Thin-Film Humidity Sensor via Inkjet Printing Technology
In this study, a highly responsive humidity sensor is developed by printing gold nanoparticles (GNPs) grafted with a hygroscopic polymer. These GNPs are inkjet-printed to form a uniform thin film over an interdigitated electrode with a controllable thickness by adjusting the printing parameters. The resistance of the printed GNP thin film decreases significantly upon exposure to water vapor and exhibits a semi-log relationship with relative humidity (RH). The sensor can detect RH variations from 1.8 to 95% with large resistance changes up to 4 orders of magnitude with no hysteresis and small temperature dependence. In addition, with a small thickness, the sensor can reach absorption equilibrium quickly with response and recovery times of ≤1.2 and ≤3 s, respectively. The fast response to humidity changes also allows the GNP thin-film sensor to distinguish signals from intermittent humidification/dehumidification cycles with a frequency up to 2.5 Hz. The printed sensors on flexible substrates show little sensitivity to bending deformation and can be embedded in a mask for human respiratory detection. In summary, this study demonstrates the feasibility of applying printing technology for the fabrication of thin-film humidity sensors, and the methodology developed can be further applied to fabricate many other types of nanoparticle-based sensor devices.
- 4 January 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (9) , 3256-3264
Highly Responsive PEG/Gold Nanoparticle Thin-Film Humidity Sensor via Inkjet Printing Technology
In this study, a highly responsive humidity sensor is developed by printing gold nanoparticles (GNPs) grafted with a hygroscopic polymer. These GNPs are inkjet-printed to form a uniform thin film over an interdigitated electrode with a controllable thickness by adjusting the printing parameters. The resistance of the printed GNP thin film decreases significantly upon exposure to water vapor and exhibits a semi-log relationship with relative humidity (RH). The sensor can detect RH variations from 1.8 to 95% with large resistance changes up to 4 orders of magnitude with no hysteresis and small temperature dependence. In addition, with a small thickness, the sensor can reach absorption equilibrium quickly with response and recovery times of ≤1.2 and ≤3 s, respectively. The fast response to humidity changes also allows the GNP thin-film sensor to distinguish signals from intermittent humidification/dehumidification cycles with a frequency up to 2.5 Hz. The printed sensors on flexible substrates show little sensitivity to bending deformation and can be embedded in a mask for human respiratory detection. In summary, this study demonstrates the feasibility of applying printing technology for the fabrication of thin-film humidity sensors, and the methodology developed can be further applied to fabricate many other types of nanoparticle-based sensor devices.
- 3 October 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (43) , 37374-37385
Fabrication of Strain Gauges via Contact Printing: A Simple Route to Healthcare Sensors Based on Cross-Linked Gold Nanoparticles
In this study we developed a novel and efficient process for the fabrication of resistive strain gauges for healthcare related applications. First, 1,9-nonanedithiol (9DT) cross-linked gold nanoparticle (GNP) films were prepared via layer-by-layer (LbL) spin-coating and subsequently transferred onto flexible polyimide (PI) foil by contact printing. Four point bending tests revealed linear response characteristics with gauge factors of ~14 for 4 nm sized GNPs and ~26 for 7 nm sized GNPs. This dependency of strain sensitivity is attributed to the perturbation of charge carrier tunneling between neighboring GNPs, which becomes more efficient with increasing particle size. Fatigue tests revealed that the strain-resistance performance remained nearly the same after 10.000 strain/relaxation cycles. We demonstrate that these sensors are well suited to monitor muscle movements. Furthermore, we fabricated all-printed strain sensors by directly transferring cross-linked GNP films onto soft PDMS sheets equipped with interdigitated electrodes. Due to the low elastic modulus of polydimethylsiloxane (PDMS) these sensors are easily deformed and, therefore, they respond sensitively to faint forces. When taped onto the skin above the radial artery they enable the well-resolved and robust recording of pulse waves with diagnostically relevant details.
- 3 October 2018
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 10 (43) , 37374-37385
Fabrication of Strain Gauges via Contact Printing: A Simple Route to Healthcare Sensors Based on Cross-Linked Gold Nanoparticles
In this study we developed a novel and efficient process for the fabrication of resistive strain gauges for healthcare related applications. First, 1,9-nonanedithiol (9DT) cross-linked gold nanoparticle (GNP) films were prepared via layer-by-layer (LbL) spin-coating and subsequently transferred onto flexible polyimide (PI) foil by contact printing. Four point bending tests revealed linear response characteristics with gauge factors of ~14 for 4 nm sized GNPs and ~26 for 7 nm sized GNPs. This dependency of strain sensitivity is attributed to the perturbation of charge carrier tunneling between neighboring GNPs, which becomes more efficient with increasing particle size. Fatigue tests revealed that the strain-resistance performance remained nearly the same after 10.000 strain/relaxation cycles. We demonstrate that these sensors are well suited to monitor muscle movements. Furthermore, we fabricated all-printed strain sensors by directly transferring cross-linked GNP films onto soft PDMS sheets equipped with interdigitated electrodes. Due to the low elastic modulus of polydimethylsiloxane (PDMS) these sensors are easily deformed and, therefore, they respond sensitively to faint forces. When taped onto the skin above the radial artery they enable the well-resolved and robust recording of pulse waves with diagnostically relevant details.