Shamim Hossan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shamim Hossan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- A. A. S. Mostofa Zahid
Department of Chemistry, University of Rajshahi, Rajshahi 6205, Bangladesh
2 shared publications - Bungo Ochiai
Graduate School of Science and Engineering, Yamagata University, Yonezawa 990-8510, Japan
2 shared publications - M. Habibur Rahman
Department of Chemistry, University of Rajshahi, Rajshahi 6205, Bangladesh
2 shared publications - M. Nur E. Alam
Bangladesh Atomic Energy Commission, Dhaka 1207, Bangladesh
2 shared publications - Nahid Parvez Roni
Department of Chemistry, University of Rajshahi, Rajshahi 6205, Bangladesh
2 shared publications Abdullah Munsi
1 shared publication
Latest Publications
- Open Access
Optimizing β-Phase Content in PVDF Membranes via Modification of Dope Solution with Citric Acid/Nano-TiO2 Using Nonsolvent-Induced Phase Separation Method
The morphology of Poly (vinylidene fluoride) (PVDF) membranes prepared via the nonsolvent-induced phase separation (NIPS) method was modulated by altering the dope solution with citric acid (CA) and titanium dioxide nanoparticles (nano-TiO2) to optimize the β-phase content. Three series of dope solutions were prepared in dimethyl acetamide (DMAc): (i) TONx series contained 0.0–10% citric acid, (ii) Mx series contained 0.0–0.4% nano-TiO2, and (iii) TAx series contained 5% CA and 0.0–0.40% nano-TiO2. A field emission scanning electron microscopy (FESEM) study revealed that CA enhances pore opening, and nano-TiO2 transforms the sponge-like uneven porous structures into a compact, relatively regular honeycomb structure in the PVDF membranes. The combined effect of CA and nano-TiO2 in the dope solution made the channels and chambers of the membrane well organized, and the walls of the channels transformed from solid fibrils to cross-woven nanofiber-like entities. Porosity initially peaked at 84% in the TAx series, gradually decreasing to 72% with increasing nano-TiO2 concentrations. X-ray diffraction (XRD), Fourier-Transformed Infrared Spectroscopy (FTIR), and Differential Scanning Calorimetry (DSC) revealed the presence of a combined relative amount of the β- and γ-polymorphs of 84% in a neat PVDF membrane, 88% in an Mx, and 96% in a TAx series membrane, with the β-PVDF constituting nearly the entire portion of the combined polymorphs. The presence of 96% electroactive polymorph content in the PVDF membrane is noteworthy, highlighting its potential biomedical and industrial applications.
Open AccessOptimizing β-Phase Content in PVDF Membranes via Modification of Dope Solution with Citric Acid/Nano-TiO2 Using Nonsolvent-Induced Phase Separation Method
The morphology of Poly (vinylidene fluoride) (PVDF) membranes prepared via the nonsolvent-induced phase separation (NIPS) method was modulated by altering the dope solution with citric acid (CA) and titanium dioxide nanoparticles (nano-TiO2) to optimize the β-phase content. Three series of dope solutions were prepared in dimethyl acetamide (DMAc): (i) TONx series contained 0.0–10% citric acid, (ii) Mx series contained 0.0–0.4% nano-TiO2, and (iii) TAx series contained 5% CA and 0.0–0.40% nano-TiO2. A field emission scanning electron microscopy (FESEM) study revealed that CA enhances pore opening, and nano-TiO2 transforms the sponge-like uneven porous structures into a compact, relatively regular honeycomb structure in the PVDF membranes. The combined effect of CA and nano-TiO2 in the dope solution made the channels and chambers of the membrane well organized, and the walls of the channels transformed from solid fibrils to cross-woven nanofiber-like entities. Porosity initially peaked at 84% in the TAx series, gradually decreasing to 72% with increasing nano-TiO2 concentrations. X-ray diffraction (XRD), Fourier-Transformed Infrared Spectroscopy (FTIR), and Differential Scanning Calorimetry (DSC) revealed the presence of a combined relative amount of the β- and γ-polymorphs of 84% in a neat PVDF membrane, 88% in an Mx, and 96% in a TAx series membrane, with the β-PVDF constituting nearly the entire portion of the combined polymorphs. The presence of 96% electroactive polymorph content in the PVDF membrane is noteworthy, highlighting its potential biomedical and industrial applications.
- Open Access
Selectivity of Sol-Gel and Hydrothermal TiO2 Nanoparticles towards Photocatalytic Degradation of Cationic and Anionic Dyes
Titanium dioxide (TiO2) nanoparticles have been extensively studied for catalyzing the photo-degradation of organic pollutants, the photocatalyst being nonselective to the substrate. We, however, found that TiO2 nanoparticles prepared via the sol-gel and hydrothermal synthetic routes each possess a definite specificity to the charge of the substrate for photodegradation. The nanoparticles were characterized by SEM, FTIR, XRD, TGA, and UV-visible spectra, and the photocatalytic degradation under UV-B (285 nm) irradiation of two model compounds, anionic methyl Orange (MO) and cationic methylene blue (MB) was monitored by a UV-visible spectrophotometer. Untreated sol-gel TiO2 nanoparticles (Tsg) preferentially degraded MO over MB (90% versus 40% in two hours), while after calcination at 400 °C for two hours (Tsgc) they showed reversed specificity (50% MO versus 90% MB in one hour). The as-prepared hydrothermal TiO2 nanoparticles (Tht) behaved in the opposite sense of Tsg (41% MO versus 91% MB degraded in one and a half hours); calcination at 400 °C (Thtc) did not reverse the trend but enhanced the efficiency of degradation. The study indicates that TiO2 nanoparticles can be made to degrade a specific class of organic pollutants from an effluent facilitating the recycling of a specific class of pollutants for cost-effective effluent management.
Open AccessSelectivity of Sol-Gel and Hydrothermal TiO2 Nanoparticles towards Photocatalytic Degradation of Cationic and Anionic Dyes
Titanium dioxide (TiO2) nanoparticles have been extensively studied for catalyzing the photo-degradation of organic pollutants, the photocatalyst being nonselective to the substrate. We, however, found that TiO2 nanoparticles prepared via the sol-gel and hydrothermal synthetic routes each possess a definite specificity to the charge of the substrate for photodegradation. The nanoparticles were characterized by SEM, FTIR, XRD, TGA, and UV-visible spectra, and the photocatalytic degradation under UV-B (285 nm) irradiation of two model compounds, anionic methyl Orange (MO) and cationic methylene blue (MB) was monitored by a UV-visible spectrophotometer. Untreated sol-gel TiO2 nanoparticles (Tsg) preferentially degraded MO over MB (90% versus 40% in two hours), while after calcination at 400 °C for two hours (Tsgc) they showed reversed specificity (50% MO versus 90% MB in one hour). The as-prepared hydrothermal TiO2 nanoparticles (Tht) behaved in the opposite sense of Tsg (41% MO versus 91% MB degraded in one and a half hours); calcination at 400 °C (Thtc) did not reverse the trend but enhanced the efficiency of degradation. The study indicates that TiO2 nanoparticles can be made to degrade a specific class of organic pollutants from an effluent facilitating the recycling of a specific class of pollutants for cost-effective effluent management.
- Open Access
- 22 May 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (9) , B3240-B3245
Detailed Study on Rapid Removal of Cationic Dyes Using TiO2-Poly(3-Chloro-2-Hydroxypropyl Methacrylate) Nanocomposite
This study focused on TiO2-poly(3-chloro-2-hydroxypropyl methacrylate) (TiO2-PCHPMA) for rapid removal of cationic dyes from aqueous solutions by adsorption and degradation. TiO2-PCHPMA adsorbed cationic dyes, basic red 2 (BR2), basic red 5 (BR5), basic blue 17 (BB17), and methylene blue (MB), quantitatively in a wide range of pH from 5 to 10. The adsorption proceeded very rapidly, and reached equilibrium in a few seconds. TiO2-PCHPMA selectively separated cationic MB from a mixture with anionic methyl orange by the selective adsorption ability. The photocatalytic activity of TiO2-PCHPMA under UV irradiation was higher than that of bare TiO2. The excellent removal efficiency of TiO2-PCHPMA either by adsorption or degradation is advantageous in applications for treatment of industrial effluents by the selective separation by adsorption and degradation under UV irradiation.
- 22 May 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (9) , B3240-B3245
Open AccessDetailed Study on Rapid Removal of Cationic Dyes Using TiO2-Poly(3-Chloro-2-Hydroxypropyl Methacrylate) Nanocomposite
This study focused on TiO2-poly(3-chloro-2-hydroxypropyl methacrylate) (TiO2-PCHPMA) for rapid removal of cationic dyes from aqueous solutions by adsorption and degradation. TiO2-PCHPMA adsorbed cationic dyes, basic red 2 (BR2), basic red 5 (BR5), basic blue 17 (BB17), and methylene blue (MB), quantitatively in a wide range of pH from 5 to 10. The adsorption proceeded very rapidly, and reached equilibrium in a few seconds. TiO2-PCHPMA selectively separated cationic MB from a mixture with anionic methyl orange by the selective adsorption ability. The photocatalytic activity of TiO2-PCHPMA under UV irradiation was higher than that of bare TiO2. The excellent removal efficiency of TiO2-PCHPMA either by adsorption or degradation is advantageous in applications for treatment of industrial effluents by the selective separation by adsorption and degradation under UV irradiation.
- 13 December 2018
- Published by The Electrochemical Society in ECS Transactions
- Vol. 88 (1) , 75-87
Detailed Study on Rapid Removal of Cationic Dyes Using TiO2-Poly(3-Chloro-2-Hydroxypropyl Methacrylate) Nanocomposite
This study focused on TiO2-poly(3-chloro-2-hydroxypropyl methacrylate) (TiO2-PCHPMA) for rapid removal of cationic dyes from aqueous solutions by adsorption and degradation. TiO2-PCHPMA adsorbed cationic dyes, basic red 2 (BR2), basic red 5 (BR5), basic blue 17 (BB17), and methylene blue (MB), quantitatively in a wide range of pH from 5 to 10. The adsorption proceeded very rapidly, and reached equilibrium in a few seconds. TiO2-PCHPMA selectively separated cationic MB from a mixture with anionic methyl orange by the selective adsorption ability. The photocatalytic activity of TiO2-PCHPMA under UV irradiation was higher than that of bare TiO2. The excellent removal efficiency of TiO2-PCHPMA either by adsorption or degradation is advantageous in applications for treatment of industrial effluents by the selective separation by adsorption and degradation under UV irradiation.
- 13 December 2018
- Published by The Electrochemical Society in ECS Transactions
- Vol. 88 (1) , 75-87
Detailed Study on Rapid Removal of Cationic Dyes Using TiO2-Poly(3-Chloro-2-Hydroxypropyl Methacrylate) Nanocomposite
This study focused on TiO2-poly(3-chloro-2-hydroxypropyl methacrylate) (TiO2-PCHPMA) for rapid removal of cationic dyes from aqueous solutions by adsorption and degradation. TiO2-PCHPMA adsorbed cationic dyes, basic red 2 (BR2), basic red 5 (BR5), basic blue 17 (BB17), and methylene blue (MB), quantitatively in a wide range of pH from 5 to 10. The adsorption proceeded very rapidly, and reached equilibrium in a few seconds. TiO2-PCHPMA selectively separated cationic MB from a mixture with anionic methyl orange by the selective adsorption ability. The photocatalytic activity of TiO2-PCHPMA under UV irradiation was higher than that of bare TiO2. The excellent removal efficiency of TiO2-PCHPMA either by adsorption or degradation is advantageous in applications for treatment of industrial effluents by the selective separation by adsorption and degradation under UV irradiation.