Girija Shankar Sahoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Girija Shankar Sahoo has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Guru Prasad Mishra
Department of Electronics and Communication Engineering National Institute of Technology Raipur Raipur India
11 shared publications Guru Prasad Mishra
7 shared publicationsOkba Saidani
ETA Laboratory, Department of Electronics, IET Institute, University Mohamed El Bachir El Ibrahimi of Bordj Bou, El Anceur, Algeria
7 shared publicationsAbderrahim Yousfi
ETA Laboratory, IET Institute, University Mohamed El Bachir El Ibrahimi of Bordj Bou, Arréridj, Algeria
6 shared publicationsG.P. Mishra
5 shared publicationsSagar Bhattarai
5 shared publications
Latest Publications
- 14 October 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (20)
Optimization of Perovskite‐Silicon Alloy Dual‐Junction Architectures for Next‐Generation Solar Cells
This study investigates the enhancement of silicon‐based photovoltaic performance through bandgap engineering using silicon alloy materials. The Shockley–Queisser (SQ) limit defines the maximum efficiency for unijunction solar cells and restricts conventional crystalline silicon devices due to their fixed bandgap of 1.12 eV. To alleviate this constraint, this work proposes using a germanium‐based silicon alloy, SiGe, which enables tunable bandgaps that improve spectral response and reduce carrier thermalization losses. SCAPS‐1D is utilized to perform numerical simulations and compare the optoelectronic characteristics of a conventional silicon device with those of engineered silicon alloy structures. The optimized silicon alloy solar cell achieved an open circuit voltage of 0.7368 V and a power conversion efficiency (PCE) of 28.52%, representing a notable improvement over the 24.59% PCE obtained for the standard silicon cell. Furthermore, design and analysis of a two‐terminal tandem configuration integrating a wide‐bandgap perovskite top cell with a silicon alloy bottom subcell are carried out. The tandem architecture demonstrated superior spectral utilization of both high‐ and low‐energy photons, resulting in a simulated overall PCE exceeding 42%, thereby surpassing the single‐junction SQ limit. These findings highlight the significant promise of bandgap‐engineered silicon alloys, particularly when incorporated into perovskite/silicon tandem configurations, for the development of next‐generation high‐efficiency photovoltaic technologies.
- 14 October 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (20)
Optimization of Perovskite‐Silicon Alloy Dual‐Junction Architectures for Next‐Generation Solar Cells
This study investigates the enhancement of silicon‐based photovoltaic performance through bandgap engineering using silicon alloy materials. The Shockley–Queisser (SQ) limit defines the maximum efficiency for unijunction solar cells and restricts conventional crystalline silicon devices due to their fixed bandgap of 1.12 eV. To alleviate this constraint, this work proposes using a germanium‐based silicon alloy, SiGe, which enables tunable bandgaps that improve spectral response and reduce carrier thermalization losses. SCAPS‐1D is utilized to perform numerical simulations and compare the optoelectronic characteristics of a conventional silicon device with those of engineered silicon alloy structures. The optimized silicon alloy solar cell achieved an open circuit voltage of 0.7368 V and a power conversion efficiency (PCE) of 28.52%, representing a notable improvement over the 24.59% PCE obtained for the standard silicon cell. Furthermore, design and analysis of a two‐terminal tandem configuration integrating a wide‐bandgap perovskite top cell with a silicon alloy bottom subcell are carried out. The tandem architecture demonstrated superior spectral utilization of both high‐ and low‐energy photons, resulting in a simulated overall PCE exceeding 42%, thereby surpassing the single‐junction SQ limit. These findings highlight the significant promise of bandgap‐engineered silicon alloys, particularly when incorporated into perovskite/silicon tandem configurations, for the development of next‐generation high‐efficiency photovoltaic technologies.
- 18 June 2026
- Published by Elsevier in Materials Research Bulletin
- Vol. 204
Toward high-efficiency lead-free Cs₂YCuBr₆ perovskite solar cells: Role of transport layers and defects
- 18 June 2026
- Published by Elsevier in Materials Research Bulletin
- Vol. 204
Toward high-efficiency lead-free Cs₂YCuBr₆ perovskite solar cells: Role of transport layers and defects
- 17 April 2026
- Published by Springer Nature in Journal of Optics
- p. 1-13
Exploring the potential of lead-free NaZnBr3 perovskites for high-efficiency solar cells
- 17 April 2026
- Published by Springer Nature in Journal of Optics
- p. 1-13
Exploring the potential of lead-free NaZnBr3 perovskites for high-efficiency solar cells
- 18 August 2025
- Published by Elsevier in Materials Research Bulletin
- Vol. 194
Harnessing machine learning to revolutionize perovskite solar cells: Optimizing RbTmCl3-based photovoltaic performance
- 18 August 2025
- Published by Elsevier in Materials Research Bulletin
- Vol. 194
Harnessing machine learning to revolutionize perovskite solar cells: Optimizing RbTmCl3-based photovoltaic performance
- 10 April 2025
- Published by Springer Nature in Transactions on Electrical and Electronic Materials
- Vol. 26 (3) , 366-379
Numerical Simulation of High-Efficiency Double-Absorber Layer Perovskite Solar Cells Using SCAPS- 1D and MATLAB PV Models
- 10 April 2025
- Published by Springer Nature in Transactions on Electrical and Electronic Materials
- Vol. 26 (3) , 366-379
Numerical Simulation of High-Efficiency Double-Absorber Layer Perovskite Solar Cells Using SCAPS- 1D and MATLAB PV Models