Giancarlo Corti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Giancarlo Corti has a total of 119 co-authors. Here are the top co-authors by number of shared publications:
Timothy Cantrell
University of Idaho
6 shared publicationsTej Prakash
University of Idaho
4 shared publicationsAlexander Larin
Department of Physics and Astronomy, Western Kentucky University, Bowling Green, Kentucky 42101-1077, United States
3 shared publicationsDavid N. McIlroy
Department of Physics, University of Idaho, Moscow, Idaho 83844-0903, United States
3 shared publicationsDewayne Sowell
Department of Physics and Astronomy, Western Kentucky University, Bowling Green, Kentucky 42101-1077, United States
3 shared publicationsJessica Hall
Department of Physics and Astronomy, Western Kentucky University, Bowling Green, Kentucky 42101-1077, United States
3 shared publications
Latest Publications
- Open Access
Microstructural Characterization and Property of Carbon Fiber Reinforced High-Density Polyethylene Composites Fabricated by Fused Deposition Modeling
As a promising industrial thermoplastic polymer material, high-density polyethylene (HDPE) possesses distinct properties of ease to process, good biocompatibility, high recyclability, etc. and has been widely used to make packaging, prostheses and implants, and liquid-permeable membranes. Traditional manufacturing processes for HDPE, including injection molding, thermoforming, and rotational molding, require molds or post processing. In addition, part shapes are highly restricted., Thus, fused deposition modeling (FDM) is introduced to process HDPE materials to take advantage of FDM’s free of design, no mold requirement, ease and low cost of processing. To improve the mechanical properties (such as stiffness and strength) and thermal resistance of HDPE, carbon fiber (CF) was incorporated into HDPE, and CF-reinforced HDPE composites were successfully fabricated using FDM process. In addition, the effects of CF content on surface quality, microstructure characterizations, tensile properties, dynamic mechanical properties, and thermal properties have been investigated. Experimental results show that an appropriate CF content addition is beneficial for improving surface quality, and mechanical and thermal properties.
Open AccessMicrostructural Characterization and Property of Carbon Fiber Reinforced High-Density Polyethylene Composites Fabricated by Fused Deposition Modeling
As a promising industrial thermoplastic polymer material, high-density polyethylene (HDPE) possesses distinct properties of ease to process, good biocompatibility, high recyclability, etc. and has been widely used to make packaging, prostheses and implants, and liquid-permeable membranes. Traditional manufacturing processes for HDPE, including injection molding, thermoforming, and rotational molding, require molds or post processing. In addition, part shapes are highly restricted., Thus, fused deposition modeling (FDM) is introduced to process HDPE materials to take advantage of FDM’s free of design, no mold requirement, ease and low cost of processing. To improve the mechanical properties (such as stiffness and strength) and thermal resistance of HDPE, carbon fiber (CF) was incorporated into HDPE, and CF-reinforced HDPE composites were successfully fabricated using FDM process. In addition, the effects of CF content on surface quality, microstructure characterizations, tensile properties, dynamic mechanical properties, and thermal properties have been investigated. Experimental results show that an appropriate CF content addition is beneficial for improving surface quality, and mechanical and thermal properties.
- Open Access
Improved Electrical Signal of Non-Poled 3D Printed Zinc Oxide-Polyvinylidene Fluoride Nanocomposites
Polyvinylidene fluoride (PVDF) presents highly useful piezo and pyro electric properties but they are predicated upon the processing methods and the ensuing volume fraction of the β-phase. Production of PVDF with higher β-phase content for additive manufacturing (AM) is particularly desirable because it can enable the creation of custom parts with enhanced properties. Necessary steps from compounding to the testing of a 3D printed piezo sensitive sensor are presented in this paper. AM process variables and the influence of zinc oxide (ZnO) nanofiller on crystallinity, viscosity, and electromechanical properties of PVDF, have been explored. Fourier-transform infrared spectroscopy (FTIR) measurements confirm that a high cooling rate (HCR) of 30 °C min−1 promotes the conversion of the α-into the β-phase, reaching a maximum of 80% conversion with 7.5–12.5% ZnO content. These processing conditions increase the elastic modulus up to 40%, while maintaining the ultimate strength, ≈46 MPa. Furthermore, HCR 10% ZnO-PVDF produces four times higher volts per Newton when compared to low cooling rate, 5 °C min−1, pristine PVDF. A piezoelectric biomedical sensor application has been presented using HCR and ZnO nanofiller. This technique also reduces the need for post-poling which can reduce manufacturing time and cost.
Open AccessImproved Electrical Signal of Non-Poled 3D Printed Zinc Oxide-Polyvinylidene Fluoride Nanocomposites
Polyvinylidene fluoride (PVDF) presents highly useful piezo and pyro electric properties but they are predicated upon the processing methods and the ensuing volume fraction of the β-phase. Production of PVDF with higher β-phase content for additive manufacturing (AM) is particularly desirable because it can enable the creation of custom parts with enhanced properties. Necessary steps from compounding to the testing of a 3D printed piezo sensitive sensor are presented in this paper. AM process variables and the influence of zinc oxide (ZnO) nanofiller on crystallinity, viscosity, and electromechanical properties of PVDF, have been explored. Fourier-transform infrared spectroscopy (FTIR) measurements confirm that a high cooling rate (HCR) of 30 °C min−1 promotes the conversion of the α-into the β-phase, reaching a maximum of 80% conversion with 7.5–12.5% ZnO content. These processing conditions increase the elastic modulus up to 40%, while maintaining the ultimate strength, ≈46 MPa. Furthermore, HCR 10% ZnO-PVDF produces four times higher volts per Newton when compared to low cooling rate, 5 °C min−1, pristine PVDF. A piezoelectric biomedical sensor application has been presented using HCR and ZnO nanofiller. This technique also reduces the need for post-poling which can reduce manufacturing time and cost.
- Open Access
- 6 May 2022
- Published by Hindawi Limited in International Journal of Reconfigurable Computing
- Vol. 2022, 1-10
A Methodology for an FPGA Implementation of a Programmable Logic Controller to Control an Atomic Layer Deposition System
In this work, we present an industrial cold walled Atomic Layer Deposition (ALD) system, which can be controlled by either a traditional programmable logic controller (PLC) system or a field-programmable gate array (FPGA) prototyping board. This work presents an FPGA controlled system that takes ladder diagram (LD) control for a PLC and converts this control to Verilog HDL and programs an FPGA such that the FPGA prototyping board is used to control a real industrial application. We explore this approach since FPGA implementation of LD control could significantly reduce the cost of implementing these controllers with other potential advantages such as the improved granularity of timing control from milliseconds to nanoseconds, additional available pins for inputs and outputs far exceeding that of microprocessors, and lower power consumption for control. In this work, we provide details and descriptions of our industrial system (ALD), the LD control of this system and its implementation, our software flow to convert LDs to Verilog HDL, and our FPGA prototype board design to replace the existing electronic controller. We show how our LD-Verilog HDL converter in conjunction with FPGAs matches a PLC and demonstrate some of the benefits of using an FPGA.
- 6 May 2022
- Published by Hindawi Limited in International Journal of Reconfigurable Computing
- Vol. 2022, 1-10
Open AccessA Methodology for an FPGA Implementation of a Programmable Logic Controller to Control an Atomic Layer Deposition System
In this work, we present an industrial cold walled Atomic Layer Deposition (ALD) system, which can be controlled by either a traditional programmable logic controller (PLC) system or a field-programmable gate array (FPGA) prototyping board. This work presents an FPGA controlled system that takes ladder diagram (LD) control for a PLC and converts this control to Verilog HDL and programs an FPGA such that the FPGA prototyping board is used to control a real industrial application. We explore this approach since FPGA implementation of LD control could significantly reduce the cost of implementing these controllers with other potential advantages such as the improved granularity of timing control from milliseconds to nanoseconds, additional available pins for inputs and outputs far exceeding that of microprocessors, and lower power consumption for control. In this work, we provide details and descriptions of our industrial system (ALD), the LD control of this system and its implementation, our software flow to convert LDs to Verilog HDL, and our FPGA prototype board design to replace the existing electronic controller. We show how our LD-Verilog HDL converter in conjunction with FPGAs matches a PLC and demonstrate some of the benefits of using an FPGA.
- Open Access
- 25 August 2020
- Published by IOP Publishing in Nano Express
- Vol. 1 (2) , 020030
Low cycles pulsed chemical vapor deposition of polycrystalline anatase TiO2
In this work, an atomic layer deposition (ALD) system is used to identify deposition conditions resulting in anisotropic growth and the formation of highly defined polycrystalline anatase titanium dioxide. FESEM, Raman Spectroscopy, and XRD were extensively used to characterize the deposited titania. The ALD parameter refinement resulted in the attainment of a polycrystalline anatase phase titania in as low as 30 cycles, although the final parameter resulted in a pulsed-chemical vapor deposition (pulsed-CVD). This work suggests that the anatase crystal phase’s development is more dependent on deposition process parameters such as precursor pulse, waiting time, and vacuum times than on the number of cycles. Moreover, the developed pulsed-CVD procedure to deposit anatase titania was capable of coating rough aluminum and titanium substrates with polycrystalline anatase titania, highly increasing the potential to be used in other biomedical implants made of different metals such as stainless steel or in other applications such as dielectrics
- 25 August 2020
- Published by IOP Publishing in Nano Express
- Vol. 1 (2) , 020030
Open AccessLow cycles pulsed chemical vapor deposition of polycrystalline anatase TiO2
In this work, an atomic layer deposition (ALD) system is used to identify deposition conditions resulting in anisotropic growth and the formation of highly defined polycrystalline anatase titanium dioxide. FESEM, Raman Spectroscopy, and XRD were extensively used to characterize the deposited titania. The ALD parameter refinement resulted in the attainment of a polycrystalline anatase phase titania in as low as 30 cycles, although the final parameter resulted in a pulsed-chemical vapor deposition (pulsed-CVD). This work suggests that the anatase crystal phase’s development is more dependent on deposition process parameters such as precursor pulse, waiting time, and vacuum times than on the number of cycles. Moreover, the developed pulsed-CVD procedure to deposit anatase titania was capable of coating rough aluminum and titanium substrates with polycrystalline anatase titania, highly increasing the potential to be used in other biomedical implants made of different metals such as stainless steel or in other applications such as dielectrics
- 17 March 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (14) , 17046-17054
Water Condensation and Droplet Shedding Behavior on Silica-Nanospring-Coated Tubes
In this work, the water condensation performance of methylated silica nanospring (SN) coated horizontal aluminum tubes is assessed. Coated samples with varying nanospring mat thicknesses, from 784 nm to 2902 nm, were studied, which exhibited static contact angles and CA hysteresis values of 155° and 20°, respectively. Dropwise condensation and increased droplet shedding were observed on these coated tubes. Video analysis determined that tubes with 15 and 20 minute SN growth times experienced an 84% increase in the condensate removal rate over the baseline. Moreover, with a hybrid wettability consisting of alternating regions of SN and bare aluminum experienced a 96% increase in condensate removal. Additionally, the average droplet departure size was reduced on these SN-coated tubes. SEM imaging and XEDS analysis were also performed on the tubes and revealed that the coating was reasonable durable having withstood the condensation environment. Moreover, the coated tubes were shown to exhibit the same XEDS spectra both before and after testing.
- 17 March 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (14) , 17046-17054
Water Condensation and Droplet Shedding Behavior on Silica-Nanospring-Coated Tubes
In this work, the water condensation performance of methylated silica nanospring (SN) coated horizontal aluminum tubes is assessed. Coated samples with varying nanospring mat thicknesses, from 784 nm to 2902 nm, were studied, which exhibited static contact angles and CA hysteresis values of 155° and 20°, respectively. Dropwise condensation and increased droplet shedding were observed on these coated tubes. Video analysis determined that tubes with 15 and 20 minute SN growth times experienced an 84% increase in the condensate removal rate over the baseline. Moreover, with a hybrid wettability consisting of alternating regions of SN and bare aluminum experienced a 96% increase in condensate removal. Additionally, the average droplet departure size was reduced on these SN-coated tubes. SEM imaging and XEDS analysis were also performed on the tubes and revealed that the coating was reasonable durable having withstood the condensation environment. Moreover, the coated tubes were shown to exhibit the same XEDS spectra both before and after testing.
- 7 January 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (4) , 4607-4615
Characterization of Methyl-Functionalized Silica Nanosprings for Superhydrophobic and Defrosting Coatings
Thin non-PFA superhydrophobic coatings are desirable for heat exchangers due to their lower thermal resistance, and reduced environmental concerns. Coatings requirements must also include robustness and longevity and facilitate high defrosting rates in refrigeration applications to warrant their adoption and use. Methyl functionalized silica nanosprings (SN) possess water droplet static contact angles above 160° with contact angle hysteresis values as low as 6.9° for a submicron thick coating. The methyl functional groups render the silica surface hydrophobic, while the geometrical and topographical characteristics of the nanosprings make it superhydrophobic. Results show that SN are capable of removing 95% of the frost from the surface at a lower temperature than the base aluminum substrate. The submicron SN coating also decreases the time to defrost by ~1.5 times and can withstand more than 20 frosting-defrosting cycles in a high humidity environment akin to real working conditions for heat exchangers.
- 7 January 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (4) , 4607-4615
Characterization of Methyl-Functionalized Silica Nanosprings for Superhydrophobic and Defrosting Coatings
Thin non-PFA superhydrophobic coatings are desirable for heat exchangers due to their lower thermal resistance, and reduced environmental concerns. Coatings requirements must also include robustness and longevity and facilitate high defrosting rates in refrigeration applications to warrant their adoption and use. Methyl functionalized silica nanosprings (SN) possess water droplet static contact angles above 160° with contact angle hysteresis values as low as 6.9° for a submicron thick coating. The methyl functional groups render the silica surface hydrophobic, while the geometrical and topographical characteristics of the nanosprings make it superhydrophobic. Results show that SN are capable of removing 95% of the frost from the surface at a lower temperature than the base aluminum substrate. The submicron SN coating also decreases the time to defrost by ~1.5 times and can withstand more than 20 frosting-defrosting cycles in a high humidity environment akin to real working conditions for heat exchangers.
- 6 February 2018
- Published by IOP Publishing in Nanotechnology
- Vol. 29 (11) , 115604
Threefold growth efficiency improvement of silica nanosprings by using silica nanosprings as a substrate
The growth efficiency of one-dimension (1D) nanostructures via the vapor–liquid–solid process is commonly attributed to parameters such as precursor vapor pressure, substrate temperature, and the choice of the catalyst. The work presented herein is an investigation of the use of silica nanosprings (SNs) as a 3D substrate for improving the growth efficiency of SN themselves. SNs are a 1D nanomaterial that form a nonwoven structure with optimal geometric characteristics and surface properties that mitigate collisions between growing nanosprings and ripening of the gold catalyst, which should improve SN yield. Nanospring growth, for an eight hour period, on an SN coated surface relative to an equivalent flat substrate increased from ≈25 mgh −1 to ≈80 mgh −1 , respectively. All things being equal, by splitting the typical amount of catalyst, in this case gold, between the first and second growth, the double growth procedure produced more than three times more nanosprings than the equivalent single growth of a SN. In addition, using an SN as a substrate increased the sustained growth condition from four to eight hours, and thus increased by a factor of ten the gravimetric yield of SNs relative to the mass of gold used.
- 6 February 2018
- Published by IOP Publishing in Nanotechnology
- Vol. 29 (11) , 115604
Threefold growth efficiency improvement of silica nanosprings by using silica nanosprings as a substrate
The growth efficiency of one-dimension (1D) nanostructures via the vapor–liquid–solid process is commonly attributed to parameters such as precursor vapor pressure, substrate temperature, and the choice of the catalyst. The work presented herein is an investigation of the use of silica nanosprings (SNs) as a 3D substrate for improving the growth efficiency of SN themselves. SNs are a 1D nanomaterial that form a nonwoven structure with optimal geometric characteristics and surface properties that mitigate collisions between growing nanosprings and ripening of the gold catalyst, which should improve SN yield. Nanospring growth, for an eight hour period, on an SN coated surface relative to an equivalent flat substrate increased from ≈25 mgh −1 to ≈80 mgh −1 , respectively. All things being equal, by splitting the typical amount of catalyst, in this case gold, between the first and second growth, the double growth procedure produced more than three times more nanosprings than the equivalent single growth of a SN. In addition, using an SN as a substrate increased the sustained growth condition from four to eight hours, and thus increased by a factor of ten the gravimetric yield of SNs relative to the mass of gold used.
- Open Access
- 1 January 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (1) , 015004
Nucleation, evolution, and growth dynamics of amorphous silica nanosprings
- 1 January 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (1) , 015004
Open AccessNucleation, evolution, and growth dynamics of amorphous silica nanosprings
- 14 July 2014
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 6 (16) , 13355-13366
Self-Assembled Monolayers of Thiols Adsorbed on Au/ZnO-Functionalized Silica Nanosprings: Photoelectron Spectroscopy-Analysis and Detection of Vaporized Explosives
Self-assembled monolayers (SAMs) of thiols of l-cysteine, 6-mercaptohexanol, 4-mercaptobenzoic acid, dl-thioctic acid and 11-(1-pyrenyl)-1-undecathiol, which have been selected for their propensity to interact with vaporized explosives, have been attached from solution onto gold decorated ZnO-coated nanosprings. X-ray and ultraviolet photoelectron spectroscopies (XPS and UPS) have been used to investigate the surface electronic structure of the SAMs coated nanosprings. On the basis of XPS analysis, it has been determined that the packing densities of l-cysteine, 6-mercaptohexanol, 4-mercaptobenzoic acid, dl-thioctic acid and 11-(1-pyrenyl)-1-undecathiol on gold (zinc oxide) are 5.42 × 1014 (2.83 × 1014), 3.26 × 1014 (2.54 × 1014), 9.50 × 1013, 2.55 × 1014 (1.12 × 1014), and 5.23 × 1013 molecules/cm2, respectively. A single S 2p core level doublet is observed for 4-mercaptobenzoic acid and 11-(1-pyrenyl)-1-undecathiol, which is assigned to the S–Au bond. The S 2p core level for l-cysteine, 6-mercaptohexanol, and DL-thioctic acid consist of two doublets, where one is S–Au bond and the other is the S–Zn bond. Analysis of the C/S ratios agrees well with the stoichiometry of the respective thiols. UPS analysis shows that the hybridization of S 3p states and Au d-bands produces antibonding and bonding states, above and below the Au d-bands, which is characteristic of molecular chemisorption on Au nanoparticles. Gas sensors were constructed with thiolated nanosprings and their responsiveness to ammonium nitrate at 100–150 °C was tested. Nanosprings sensors functionalized with 4-mercaptobenzoic acid and 6-mercaptohexanol showed the strongest responses by a factor of 4 to 5 relative to the less responsive thiols. The response to ammonium nitrate can be correlated to the packing density and ordering of the SAMs.
- 14 July 2014
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 6 (16) , 13355-13366
Self-Assembled Monolayers of Thiols Adsorbed on Au/ZnO-Functionalized Silica Nanosprings: Photoelectron Spectroscopy-Analysis and Detection of Vaporized Explosives
Self-assembled monolayers (SAMs) of thiols of l-cysteine, 6-mercaptohexanol, 4-mercaptobenzoic acid, dl-thioctic acid and 11-(1-pyrenyl)-1-undecathiol, which have been selected for their propensity to interact with vaporized explosives, have been attached from solution onto gold decorated ZnO-coated nanosprings. X-ray and ultraviolet photoelectron spectroscopies (XPS and UPS) have been used to investigate the surface electronic structure of the SAMs coated nanosprings. On the basis of XPS analysis, it has been determined that the packing densities of l-cysteine, 6-mercaptohexanol, 4-mercaptobenzoic acid, dl-thioctic acid and 11-(1-pyrenyl)-1-undecathiol on gold (zinc oxide) are 5.42 × 1014 (2.83 × 1014), 3.26 × 1014 (2.54 × 1014), 9.50 × 1013, 2.55 × 1014 (1.12 × 1014), and 5.23 × 1013 molecules/cm2, respectively. A single S 2p core level doublet is observed for 4-mercaptobenzoic acid and 11-(1-pyrenyl)-1-undecathiol, which is assigned to the S–Au bond. The S 2p core level for l-cysteine, 6-mercaptohexanol, and DL-thioctic acid consist of two doublets, where one is S–Au bond and the other is the S–Zn bond. Analysis of the C/S ratios agrees well with the stoichiometry of the respective thiols. UPS analysis shows that the hybridization of S 3p states and Au d-bands produces antibonding and bonding states, above and below the Au d-bands, which is characteristic of molecular chemisorption on Au nanoparticles. Gas sensors were constructed with thiolated nanosprings and their responsiveness to ammonium nitrate at 100–150 °C was tested. Nanosprings sensors functionalized with 4-mercaptobenzoic acid and 6-mercaptohexanol showed the strongest responses by a factor of 4 to 5 relative to the less responsive thiols. The response to ammonium nitrate can be correlated to the packing density and ordering of the SAMs.
- 26 November 2013
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 46 (50)
The effects of nanoscale geometry and spillover on room temperature storage of hydrogen on silica nanosprings
- 26 November 2013
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 46 (50)
The effects of nanoscale geometry and spillover on room temperature storage of hydrogen on silica nanosprings