Mohamed Morsy-Osman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohamed Morsy-Osman has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
David V. Plant
Department of Electrical and Computer Engineering, McGill University, Montreal, Quebec, H3A 0E9, Canada
11 shared publicationsXian Xu
6 shared publications- Mathieu Chagnon
Nokia Bell Labs, Stuttgart, Germany
5 shared publications - Qunbi Zhuge
Shanghai Jiao Tong University
5 shared publications - Alireza Samani
Department of Electrical and Computer Engineering, McGill University, Montreal, Quebec Canada H3A 0E9
4 shared publications - David V. Plant
Department of Electrical and Computer Engineering McGill University H3A 2A7 Montreal QC Canada
4 shared publications
Latest Publications
- 2 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (10) , 799-802
25 and 50 Gb/s/${{\lambda}}$ PAM-4 Transmission Over 43 and 21 km Using a Simplified Coherent Receiver on SOI
We demonstrate 25 and 50 Gb/s four-level pulse amplitude modulation (PAM-4) transmission over 43 and 21 km standard single mode fiber (SMF), respectively using a silicon photonic 120° hybrid based integrated simplified coherent receiver in the C-band. The integrated receiver is composed of an edge coupler, a vertical grating coupler, a polarization splitterrotator, a 3×3 multimode interference coupler based 120° hybrid and three germanium p-i-n photodetectors. For 25 Gb/s PAM- 4 transmission, we achieved receiver sensitivities of -18, -17.5, -16.6, -14.5, and -9.8 dBm in back-to-back (B2B) and after 10.5, 21, 31, and 43 km, respectively at a bit error rate (BER) below the hard-decision forward error correction (HD-FEC) threshold (i.e., 3.8 × 10–3) without using any receiver equalizer. While for the 50 Gb/s PAM-4 transmission, receiver sensitivities of - 13.6 dBm in B2B, -13.5 and -11.6 dBm after 10.5 and 21 km are obtained using 31-tap linear feed-forward equalizer (FFE). Furthermore, we achieved up to 44 Gb/s receiver equalizerfree PAM-4 transmission over 10.5 km below the HD-FEC. The characterization of the receiver at different wavelengths within the C-band is provided as well.
- 2 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (10) , 799-802
25 and 50 Gb/s/${{\lambda}}$ PAM-4 Transmission Over 43 and 21 km Using a Simplified Coherent Receiver on SOI
We demonstrate 25 and 50 Gb/s four-level pulse amplitude modulation (PAM-4) transmission over 43 and 21 km standard single mode fiber (SMF), respectively using a silicon photonic 120° hybrid based integrated simplified coherent receiver in the C-band. The integrated receiver is composed of an edge coupler, a vertical grating coupler, a polarization splitterrotator, a 3×3 multimode interference coupler based 120° hybrid and three germanium p-i-n photodetectors. For 25 Gb/s PAM- 4 transmission, we achieved receiver sensitivities of -18, -17.5, -16.6, -14.5, and -9.8 dBm in back-to-back (B2B) and after 10.5, 21, 31, and 43 km, respectively at a bit error rate (BER) below the hard-decision forward error correction (HD-FEC) threshold (i.e., 3.8 × 10–3) without using any receiver equalizer. While for the 50 Gb/s PAM-4 transmission, receiver sensitivities of - 13.6 dBm in B2B, -13.5 and -11.6 dBm after 10.5 and 21 km are obtained using 31-tap linear feed-forward equalizer (FFE). Furthermore, we achieved up to 44 Gb/s receiver equalizerfree PAM-4 transmission over 10.5 km below the HD-FEC. The characterization of the receiver at different wavelengths within the C-band is provided as well.
- Open Access
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (13) , 2989-2999
Silicon Photonic Mach–Zehnder Modulator Architectures for on Chip PAM-4 Signal Generation
Four level pulse amplitude modulation (PAM-4) has become the modulation format of choice to replace on-off keying (OOK) for the 400 Gb/s short reach optical communications systems. In this manuscript, we investigate the possible modifications to conventional Mach-Zehnder modulator structures to improve the system performance. We present 3 different Silicon photonic Mach-Zehnder modulator architectures for generating PAM-4 in the optical domain using OOK electrical driving signals. We investigate the transfer function and linearity of each modulator, and experimentally compare their PAM-4 generation and transmission performance with and without use of digital signal processing (DSP). We achieve the highest reported PAM-4 generation and transmission without the use of DSP. The power consumption of each modulator is presented, and we experimentally show that multi-electrode Mach-Zehnder modulators provide a clear advantage at higher symbol rates compared to conventional Mach-Zehnder modulators.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (13) , 2989-2999
Open AccessSilicon Photonic Mach–Zehnder Modulator Architectures for on Chip PAM-4 Signal Generation
Four level pulse amplitude modulation (PAM-4) has become the modulation format of choice to replace on-off keying (OOK) for the 400 Gb/s short reach optical communications systems. In this manuscript, we investigate the possible modifications to conventional Mach-Zehnder modulator structures to improve the system performance. We present 3 different Silicon photonic Mach-Zehnder modulator architectures for generating PAM-4 in the optical domain using OOK electrical driving signals. We investigate the transfer function and linearity of each modulator, and experimentally compare their PAM-4 generation and transmission performance with and without use of digital signal processing (DSP). We achieve the highest reported PAM-4 generation and transmission without the use of DSP. The power consumption of each modulator is presented, and we experimentally show that multi-electrode Mach-Zehnder modulators provide a clear advantage at higher symbol rates compared to conventional Mach-Zehnder modulators.
- 26 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (8) , 587-590
Optimum Three-Dimensional Constellations for Stokes Vector Direct Detect Receivers
We propose optimum three dimensional signal constellations for short reach intra-datacenter interconnects using Stokes vector receivers (SVRs). These optimum 3D alphabets maximize the so-called constellation figure of merit, which is the ratio between the squared minimum Euclidean distance and the average energy of the constellation points. Compared to dual-polarization (DP) 4-ary and 8-ary pulse amplitude modulation (PAM) formats, the optimized 16-point and 64-point 3D signal constellations theoretically achieve 4 and 6 dB improved receiver sensitivity at low symbol error rates of ~ 10-5, while delivering similar spectral efficiencies of 4 and 6 bits per 3D symbol, respectively. Next, we verified experimentally the significant improvement in receiver sensitivity at symbol rates of 44 and 64 Gbaud that result from using the proposed optimized 3D signal alphabets.
- 26 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (8) , 587-590
Optimum Three-Dimensional Constellations for Stokes Vector Direct Detect Receivers
We propose optimum three dimensional signal constellations for short reach intra-datacenter interconnects using Stokes vector receivers (SVRs). These optimum 3D alphabets maximize the so-called constellation figure of merit, which is the ratio between the squared minimum Euclidean distance and the average energy of the constellation points. Compared to dual-polarization (DP) 4-ary and 8-ary pulse amplitude modulation (PAM) formats, the optimized 16-point and 64-point 3D signal constellations theoretically achieve 4 and 6 dB improved receiver sensitivity at low symbol error rates of ~ 10-5, while delivering similar spectral efficiencies of 4 and 6 bits per 3D symbol, respectively. Next, we verified experimentally the significant improvement in receiver sensitivity at symbol rates of 44 and 64 Gbaud that result from using the proposed optimized 3D signal alphabets.
- Open Access
- 14 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (1) , 1-9
Dual Parallel Multielectrode Traveling Wave Mach–Zehnder Modulator for 200 Gb/s Intra-datacenter Optical Interconnects
We present a silicon photonic dual parallel multielectrode Mach-Zehnder modulator (MEMZM) based transmitter targeting 200 Gb/s four-level pulse amplitude modulation (PAM4) short reach transceivers. The MEMZMs have an average V π and electro-optic (EO) bandwidth of 5 V and 38 GHz, respectively. The transmitter is characterized versus receiver equalizer taps, received signal power, driving voltage swing, crosstalk voltage swing, bitrate, and reach. Results reveal that using only a three-tap equalizer at the receiver, 100 Gb/s PAM4 net rate per lane can be achieved at a bit error rate (BER) below the KP4 forward error correction (KP4-FEC) threshold of 2.4 × 10 -4 . Moreover, up to 128 Gb/s can be received at a BER below the KP4-FEC threshold using only 2 Vpp and 1 Vpp driving the MEMZM segments. Then, both MEMZMs are driven simultaneously to assess the crosstalk impact on the BER performance at parallel operation. Driven by four binary signals, we demonstrate 200 Gb/s PAM4 transmission over up to 10 km of single mode fiber at a BER below the KP4-FEC threshold.
- 14 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (1) , 1-9
Open AccessDual Parallel Multielectrode Traveling Wave Mach–Zehnder Modulator for 200 Gb/s Intra-datacenter Optical Interconnects
We present a silicon photonic dual parallel multielectrode Mach-Zehnder modulator (MEMZM) based transmitter targeting 200 Gb/s four-level pulse amplitude modulation (PAM4) short reach transceivers. The MEMZMs have an average V π and electro-optic (EO) bandwidth of 5 V and 38 GHz, respectively. The transmitter is characterized versus receiver equalizer taps, received signal power, driving voltage swing, crosstalk voltage swing, bitrate, and reach. Results reveal that using only a three-tap equalizer at the receiver, 100 Gb/s PAM4 net rate per lane can be achieved at a bit error rate (BER) below the KP4 forward error correction (KP4-FEC) threshold of 2.4 × 10 -4 . Moreover, up to 128 Gb/s can be received at a BER below the KP4-FEC threshold using only 2 Vpp and 1 Vpp driving the MEMZM segments. Then, both MEMZMs are driven simultaneously to assess the crosstalk impact on the BER performance at parallel operation. Driven by four binary signals, we demonstrate 200 Gb/s PAM4 transmission over up to 10 km of single mode fiber at a BER below the KP4-FEC threshold.
- 2 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (2) , 447-459
Half-Terabit Single-Carrier Direct-Detect Transceiver, Formats, and DSP: Analysis and Demonstration
In this paper, we extend our recent work and further demonstrate and analyze a single carrier short reach direct detect transceiver and two modulation formats, DP-PAM4+4PM and DP-PAM4+3PM, for intra-data center applications delivering 504 Gb/s and 462 Gb/s, respectively. To the best of the authors' knowledge, this is the first demonstration of a transceiver delivering half a Terabit per second on a single carrier with direct detection at a BER of $1.8\times10^{-3}$, below the threshold of hard-decision FEC of 6.69% overhead. We thoroughly detail the receiver digital signal processing that leverages the performance of this transceiver and formats. We derive the adaptation of all filters and coefficients that are updated using the stochastic gradient descent algorithm. Even if the transceiver and formats are meant to be operated in the O-band, we present several performance results in the C-band, where chromatic dispersion is large. We present the performance of the 504 Gb/s single carrier over varying received signal powers and for three different MIMO/MISO filters lengths, and show that the required received power decreases by as much as 2.4 dB when 10 neighboring symbols are included in the DSP compared to 4. We also demonstrate that, when operated in the C-band, the DP-PAM4+4PM format delivers 448 Gb/s of error-free data payload over 500 m and DP-PAM4+3PM delivers 400 Gb/s of error-free payload over 1 km, independently of the state of polarization of the received signal. Finally, we experimentally compare at 84 GBaud the BER degradation of the PAM4-$\hat{x}$, PAM4-$\hat{y}$, and PM tributaries of the DP-PAM4+4PM and DP-PAM4+3PM formats from 0 to 1 km, demonstrating much worst degradation of the PAM4 bearing phase modulation caused by phase to intensity conversion via chromatic dispersion.- 2 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (2) , 447-459
Half-Terabit Single-Carrier Direct-Detect Transceiver, Formats, and DSP: Analysis and Demonstration
In this paper, we extend our recent work and further demonstrate and analyze a single carrier short reach direct detect transceiver and two modulation formats, DP-PAM4+4PM and DP-PAM4+3PM, for intra-data center applications delivering 504 Gb/s and 462 Gb/s, respectively. To the best of the authors' knowledge, this is the first demonstration of a transceiver delivering half a Terabit per second on a single carrier with direct detection at a BER of $1.8\times10^{-3}$, below the threshold of hard-decision FEC of 6.69% overhead. We thoroughly detail the receiver digital signal processing that leverages the performance of this transceiver and formats. We derive the adaptation of all filters and coefficients that are updated using the stochastic gradient descent algorithm. Even if the transceiver and formats are meant to be operated in the O-band, we present several performance results in the C-band, where chromatic dispersion is large. We present the performance of the 504 Gb/s single carrier over varying received signal powers and for three different MIMO/MISO filters lengths, and show that the required received power decreases by as much as 2.4 dB when 10 neighboring symbols are included in the DSP compared to 4. We also demonstrate that, when operated in the C-band, the DP-PAM4+4PM format delivers 448 Gb/s of error-free data payload over 500 m and DP-PAM4+3PM delivers 400 Gb/s of error-free payload over 1 km, independently of the state of polarization of the received signal. Finally, we experimentally compare at 84 GBaud the BER degradation of the PAM4-$\hat{x}$, PAM4-$\hat{y}$, and PM tributaries of the DP-PAM4+4PM and DP-PAM4+3PM formats from 0 to 1 km, demonstrating much worst degradation of the PAM4 bearing phase modulation caused by phase to intensity conversion via chromatic dispersion.- 2 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (2) , 460-467
Enabling High-Capacity Long-Reach Direct Detection Transmission With QAM-PAM Stokes Vector Modulation
We introduce a three-dimensional modulation format using a Stokes-vector direct-detection (SV-DD) system where a pulse amplitude modulation (PAM) signal is polarization multiplexed with a quadrature amplitude modulation (QAM) signal. The phase reference of the PAM signal enables the retrieval of the phase information of the QAM signal using Stokes vector receiver (SVR). A dual polarization inphase-quadrature modulator (DP-IQM) is employed to generate QAM-PAM optical signals with chromatic dispersion (CD) pre-compensation. We show direct detection of dual-polarization (DP) 16QAM-PAM2 and 16QAM-PAM4 signals delivering 280 and 336 Gb/s below the soft-decision FEC (SD-FEC) threshold of 2 × 10-2 at 320 km and 80 km, respectively. In addition, we study system performance at different modulation formats and symbol rates. Our findings indicate that increasing the order of modulation formats of the QAM signal is better than increasing that of the PAM signal to achieve same bit rate . Finally, the performance of a 56 Gbaud 16QAM signal with PAM2 modulation on one polarization and a 56 Gbaud 16QAM signal with a pilot carrier on the orthogonal polarization with Stokes vector receiver is experimentally investigated.
- 2 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 36 (2) , 460-467
Enabling High-Capacity Long-Reach Direct Detection Transmission With QAM-PAM Stokes Vector Modulation
We introduce a three-dimensional modulation format using a Stokes-vector direct-detection (SV-DD) system where a pulse amplitude modulation (PAM) signal is polarization multiplexed with a quadrature amplitude modulation (QAM) signal. The phase reference of the PAM signal enables the retrieval of the phase information of the QAM signal using Stokes vector receiver (SVR). A dual polarization inphase-quadrature modulator (DP-IQM) is employed to generate QAM-PAM optical signals with chromatic dispersion (CD) pre-compensation. We show direct detection of dual-polarization (DP) 16QAM-PAM2 and 16QAM-PAM4 signals delivering 280 and 336 Gb/s below the soft-decision FEC (SD-FEC) threshold of 2 × 10-2 at 320 km and 80 km, respectively. In addition, we study system performance at different modulation formats and symbol rates. Our findings indicate that increasing the order of modulation formats of the QAM signal is better than increasing that of the PAM signal to achieve same bit rate . Finally, the performance of a 56 Gbaud 16QAM signal with PAM2 modulation on one polarization and a 56 Gbaud 16QAM signal with a pilot carrier on the orthogonal polarization with Stokes vector receiver is experimentally investigated.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Intensity-directed Equalizer for Chirp Compensation Enabling DML-based 56Gb/s PAM4 C-band Delivery over 35.9km SSMF
We propose an intensity-directed equalizer to address chirp induced eye skewing and intersymbol interference in DML-DD systems, and experimentally demonstrate a transmission of 56Gb/s PAM4 signals using a 16.8GHz C-band DML over 35.9 km SSMF.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Intensity-directed Equalizer for Chirp Compensation Enabling DML-based 56Gb/s PAM4 C-band Delivery over 35.9km SSMF
We propose an intensity-directed equalizer to address chirp induced eye skewing and intersymbol interference in DML-DD systems, and experimentally demonstrate a transmission of 56Gb/s PAM4 signals using a 16.8GHz C-band DML over 35.9 km SSMF.
- 24 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 35 (4) , 885-892
Multi-Dimensional Formats and Transceiver Architectures for Direct Detection With Analysis on Inter-Polarization Phase Modulation
We review the evolution of modulation formats designed for direct detection, from on-off keying intensity modulation (IM) of a single polarization to three-dimensional formats where the intensity of both polarizations and the interpolarization phase are all independently modulated. We present the transmitter and receiver architectures capable of modulating an increasing number of dimensions, all orthogonal to each other. We detail the digital signal processing for Stokes vector receivers capable of recovering all three dimensions of a lightwave via self-beating direct detection, performing simultaneously polarization derotation and mitigation of intersymbol interference. We also analyze two different transmitter architectures modulating all three dimensions where the interpolarization phase is modulated over two levels using either a direct phase modulator (DPM) or a binary phase modulator, also called a BPSK modulator. We study the impact of increasing the bandwidth efficiency from 4 to 5 b/symbol by adding two level modulation of the interpolarization phase of a dual-polarization 4-level pulse amplitude modulation (PAM4) signal on the signal quality of the PAM4 IM on the polarization bearing the phase modulator by modeling the optical fields generated by both architectures. Assuming equal quality of the driving signals to the PAM4 and phase modulator, we show that a DPM minimizes the impact on PAM4 for short reach direct detect systems operating close to the zero dispersion wavelength where chromatic dispersion is negligible.
- 24 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 35 (4) , 885-892
Multi-Dimensional Formats and Transceiver Architectures for Direct Detection With Analysis on Inter-Polarization Phase Modulation
We review the evolution of modulation formats designed for direct detection, from on-off keying intensity modulation (IM) of a single polarization to three-dimensional formats where the intensity of both polarizations and the interpolarization phase are all independently modulated. We present the transmitter and receiver architectures capable of modulating an increasing number of dimensions, all orthogonal to each other. We detail the digital signal processing for Stokes vector receivers capable of recovering all three dimensions of a lightwave via self-beating direct detection, performing simultaneously polarization derotation and mitigation of intersymbol interference. We also analyze two different transmitter architectures modulating all three dimensions where the interpolarization phase is modulated over two levels using either a direct phase modulator (DPM) or a binary phase modulator, also called a BPSK modulator. We study the impact of increasing the bandwidth efficiency from 4 to 5 b/symbol by adding two level modulation of the interpolarization phase of a dual-polarization 4-level pulse amplitude modulation (PAM4) signal on the signal quality of the PAM4 IM on the polarization bearing the phase modulator by modeling the optical fields generated by both architectures. Assuming equal quality of the driving signals to the PAM4 and phase modulator, we show that a DPM minimizes the impact on PAM4 for short reach direct detect systems operating close to the zero dispersion wavelength where chromatic dispersion is negligible.
- 1 December 2015
- Published by Elsevier in Optics Communications
- Vol. 356, 269-277
Phase-diversity method using phase-shifting interference algorithms for digital coherent receivers
- 1 December 2015
- Published by Elsevier in Optics Communications
- Vol. 356, 269-277
Phase-diversity method using phase-shifting interference algorithms for digital coherent receivers
- 5 March 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (5) , 5693-5730
Analytical and experimental performance evaluation of an integrated Si-photonic balanced coherent receiver in a colorless scenario
We study analytically and experimentally the performance limits of a Si-photonic (SiP) balanced coherent receiver (CRx) co-packaged with transimpedance amplifiers (TIAs) in a colorless WDM scheme. Firstly, the CRx architecture is depicted and characterization results are presented. Secondly, an analytical expression for the signal-to-noise ratio (SNR) at the CRx output is rigorously developed and various noise sources in the context of colorless reception are outlined. Thirdly, we study experimentally the system-level CRx performance in colorless reception of 16 × 112 Gbps PDM-QPSK WDM channels. Using a 15.5 dBm local oscillator (LO) power, error free transmissions over 4800 and 4160 km at received powers of −3 and −21 dBm per channel, respectively, were achieved in a fully colorless and preamplifierless reception. Next, a set of measurements on one of the center WDM channels is performed where the LO power, received signal power, distance, and number of channels presented to the CRx are swept to evaluate the performance limits of colorless reception. Results reveal that the LO beating with optical noise incoming with the signal is a dominant noise source regardless of received signal power. In the high received signal power regime (~0 dBm/channel), the self-beat noise from out-of-band (OOB) channels is an additional major noise source especially for small LO-to-signal power ratio, short reach and large number of OOB channels. For example, at a received signal power of 0 dBm/channel after 1600 km transmission, the SNR difference between the fully filtered and colorless scenarios, where 1 and 16 channels are passed to the CRx respectively, grows from 0.5 to 3.3 dB as the LO power changes from 12 to 0 dBm. For low received power (~-12 dBm/channel), the effect of OOB channels becomes minor while the receiver shot and thermal noises become more significant. We identify the common mode rejection ratio (CMRR) and sensitivity as the two important CRx specifications that impact the performance at high and low received signal power regimes, respectively. Finally, an excellent match between experimental and analytical SNRs is proven after the derived SNR model is fitted to the experimental data in a least-squares sense. The model is then used to predict that the CRx can operate colorlessly for a fully populated WDM spectrum with 80 channels provided that the LO-to-signal power ratio is properly set.
- 5 March 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (5) , 5693-5730
Analytical and experimental performance evaluation of an integrated Si-photonic balanced coherent receiver in a colorless scenario
We study analytically and experimentally the performance limits of a Si-photonic (SiP) balanced coherent receiver (CRx) co-packaged with transimpedance amplifiers (TIAs) in a colorless WDM scheme. Firstly, the CRx architecture is depicted and characterization results are presented. Secondly, an analytical expression for the signal-to-noise ratio (SNR) at the CRx output is rigorously developed and various noise sources in the context of colorless reception are outlined. Thirdly, we study experimentally the system-level CRx performance in colorless reception of 16 × 112 Gbps PDM-QPSK WDM channels. Using a 15.5 dBm local oscillator (LO) power, error free transmissions over 4800 and 4160 km at received powers of −3 and −21 dBm per channel, respectively, were achieved in a fully colorless and preamplifierless reception. Next, a set of measurements on one of the center WDM channels is performed where the LO power, received signal power, distance, and number of channels presented to the CRx are swept to evaluate the performance limits of colorless reception. Results reveal that the LO beating with optical noise incoming with the signal is a dominant noise source regardless of received signal power. In the high received signal power regime (~0 dBm/channel), the self-beat noise from out-of-band (OOB) channels is an additional major noise source especially for small LO-to-signal power ratio, short reach and large number of OOB channels. For example, at a received signal power of 0 dBm/channel after 1600 km transmission, the SNR difference between the fully filtered and colorless scenarios, where 1 and 16 channels are passed to the CRx respectively, grows from 0.5 to 3.3 dB as the LO power changes from 12 to 0 dBm. For low received power (~-12 dBm/channel), the effect of OOB channels becomes minor while the receiver shot and thermal noises become more significant. We identify the common mode rejection ratio (CMRR) and sensitivity as the two important CRx specifications that impact the performance at high and low received signal power regimes, respectively. Finally, an excellent match between experimental and analytical SNRs is proven after the derived SNR model is fitted to the experimental data in a least-squares sense. The model is then used to predict that the CRx can operate colorlessly for a fully populated WDM spectrum with 80 channels provided that the LO-to-signal power ratio is properly set.