Sicong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sicong Liu has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Ruidong Lv
School of Physics and Information Technology, Shaanxi Normal University, Xi’an 710119, China
6 shared publicationsYonggang Wang
School of Physics and Information Technology, Shaanxi Normal University, Xi’an 710119, China
5 shared publicationsJiang Wang
School of Physics and Information Technology, Shaanxi Normal University, Xi’an 710119, China
4 shared publications- Jiang Wang
School of Artificial Intelligence, Optics and Electronics (iOPEN), Northwestern Polytechnical University, Xi’an 710072, China
3 shared publications Yishan Wang
State Key Laboratory of Transient Optics and Photonics, Xi’an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi’an 710119, China
3 shared publications- Yonggang Wang
Shaanxi Normal University
3 shared publications
Latest Publications
- Open Access
- 10 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (22)
Perovskite nanoparticle-based nonlinear optical devices for ultrafast photonics applications
Metal halide perovskites have shown wide potential applications in various fields such as light-emitting diodes, photodetectors, and lasers in recent years due to their high photoelectric conversion efficiency, adjustable bandgap, and high carrier mobility. However, as an optical modulator for lasers, it is still limited by slow nonlinear optical response, low damage threshold, and poor stability. In this article, we prepared Cs0.15FA0.85PbI2.85Br0.15 perovskite films and used them as optical modulators to achieve ultrashort-pulse fiber lasers. By exploring the nonlinear optical response of Cs0.15FA0.85PbI2.85Br0.15 perovskite films, a saturable absorber device with 15.2% modulation depth and 20.02 ps recovery time was obtained. Based on this, it was applied in an erbium-doped fiber laser to achieve Q-switching and mode-locking pulses at a wavelength of 1550 nm. Among them, the narrowest Q-switched pulse width can reach 288 ns and the maximum single-pulse energy reaches 145.5 nJ. A soliton mode-locked pulse with a repetition rate of 32.1 MHz was achieved by adjusting the polarization state inside the cavity, with a pulse width of 276 fs and an output power of 35.12 mW. The research results indicate that Cs0.15FA0.85PbI2.85Br0.15 perovskite, as an excellent saturable absorber, has broad application prospects in the fields of ultrafast photonics.
- 10 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (22)
Open AccessPerovskite nanoparticle-based nonlinear optical devices for ultrafast photonics applications
Metal halide perovskites have shown wide potential applications in various fields such as light-emitting diodes, photodetectors, and lasers in recent years due to their high photoelectric conversion efficiency, adjustable bandgap, and high carrier mobility. However, as an optical modulator for lasers, it is still limited by slow nonlinear optical response, low damage threshold, and poor stability. In this article, we prepared Cs0.15FA0.85PbI2.85Br0.15 perovskite films and used them as optical modulators to achieve ultrashort-pulse fiber lasers. By exploring the nonlinear optical response of Cs0.15FA0.85PbI2.85Br0.15 perovskite films, a saturable absorber device with 15.2% modulation depth and 20.02 ps recovery time was obtained. Based on this, it was applied in an erbium-doped fiber laser to achieve Q-switching and mode-locking pulses at a wavelength of 1550 nm. Among them, the narrowest Q-switched pulse width can reach 288 ns and the maximum single-pulse energy reaches 145.5 nJ. A soliton mode-locked pulse with a repetition rate of 32.1 MHz was achieved by adjusting the polarization state inside the cavity, with a pulse width of 276 fs and an output power of 35.12 mW. The research results indicate that Cs0.15FA0.85PbI2.85Br0.15 perovskite, as an excellent saturable absorber, has broad application prospects in the fields of ultrafast photonics.
- 1 November 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 9 (47) , 16985-16990
Ultrafast photonics applications of zirconium carbide as a novel mode-locker for fiber lasers
Zirconium carbide (ZrC), as a novel member of the MXene family, has outstanding physical and chemical properties; however, the applications of ZrC in ultrafast photonics are still rare. Herein, a ZrC film was deposited by magnetron sputtering deposition (MSD) technology onto a D-shaped fiber and the nonlinear optical properties of the ZrC film were demonstrated. MSD technology is an advanced preparation method applicable to various materials. The saturation intensity and the modulation depth of the ZrC film were measured to be 197.6 MW cm−2 and 11.9%, respectively. After inserting the ZrC SA into an erbium-doped fiber laser (EDFL) cavity, a passive mode-locked EDFL pulse was formed. In mode-locked operation, conventional solitons with an ultrashort pulse duration of 395 fs and an output power of 49.86 mW were achieved in the communication band. The corresponding central wavelength of the output spectrum was 1562.19 nm with a 7.73 nm spectral width. This work pioneers the application of a ZrC-based device as a mode-locker to achieve ultrashort pulses for the first time and expands the application of the ZrC material. The experimental results open new opportunities for the use of ZrC in mode-locked lasers and photonics applications.
- 1 November 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 9 (47) , 16985-16990
Ultrafast photonics applications of zirconium carbide as a novel mode-locker for fiber lasers
Zirconium carbide (ZrC), as a novel member of the MXene family, has outstanding physical and chemical properties; however, the applications of ZrC in ultrafast photonics are still rare. Herein, a ZrC film was deposited by magnetron sputtering deposition (MSD) technology onto a D-shaped fiber and the nonlinear optical properties of the ZrC film were demonstrated. MSD technology is an advanced preparation method applicable to various materials. The saturation intensity and the modulation depth of the ZrC film were measured to be 197.6 MW cm−2 and 11.9%, respectively. After inserting the ZrC SA into an erbium-doped fiber laser (EDFL) cavity, a passive mode-locked EDFL pulse was formed. In mode-locked operation, conventional solitons with an ultrashort pulse duration of 395 fs and an output power of 49.86 mW were achieved in the communication band. The corresponding central wavelength of the output spectrum was 1562.19 nm with a 7.73 nm spectral width. This work pioneers the application of a ZrC-based device as a mode-locker to achieve ultrashort pulses for the first time and expands the application of the ZrC material. The experimental results open new opportunities for the use of ZrC in mode-locked lasers and photonics applications.
- 6 June 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 9 (28) , 9021-9027
Application prospects of boron nitride as a novel saturable absorber device for ultrashort pulse generation in fiber lasers
For the first time a BN-FM SA has been used in mode-locked fiber lasers, which complements the possibilities of the BN material in mode-locked lasers for ultrashort pulse generation.
- 6 June 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 9 (28) , 9021-9027
Application prospects of boron nitride as a novel saturable absorber device for ultrashort pulse generation in fiber lasers
For the first time a BN-FM SA has been used in mode-locked fiber lasers, which complements the possibilities of the BN material in mode-locked lasers for ultrashort pulse generation.
- 13 April 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 13 (16) , 19128-19137
Molybdenum Carbide Buried in D-Shaped Fibers as a Novel Saturable Absorber Device for Ultrafast Photonics Applications
Study of nonlinear laser–matter interactions in 2D materials has promoted development of photonics applications. As a typical MXene material, molybdenum carbide (Mo2C) has attracted much attention because of its graphene-like structure. Here, a type of D-shaped fiber (DF)-buried Mo2C saturable absorber (SA) fabricated by magnetron-sputtering deposition (MSD) and sol–gel technique is reported. The Mo2C material was buried between the bottom DF and the upper amorphous silica fabricated by sol–gel technology. Therefore, the DF-based SA effectively solves the problem of material shedding and aging, thus improving the stability and damage threshold of the fiber laser. Application of the SA in erbium-doped fiber laser and stable passive Q-switched operation with a maximum pulse energy of 430.47 nJ is realized. By adjusting the polarization state and pump power, high-power mode-locked pulses are generated with a pulse duration and output power of 199 fs and 54.13 mW, respectively. Further, bound-state soliton pulses are obtained with a pulse width of 312 fs and soliton interval of 1.26 ps for the first time based on MXene materials. Moreover, by application of the SA in ytterbium-doped fiber lasers, a stable dissipative soliton mode-locked pulse is obtained with a pulse width of 23 ps. These results indicate that the DF-based buried Mo2C as a novel SA provides a reliable method for all-fiber and multifunctional high-power ultrafast laser.
- 13 April 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 13 (16) , 19128-19137
Molybdenum Carbide Buried in D-Shaped Fibers as a Novel Saturable Absorber Device for Ultrafast Photonics Applications
Study of nonlinear laser–matter interactions in 2D materials has promoted development of photonics applications. As a typical MXene material, molybdenum carbide (Mo2C) has attracted much attention because of its graphene-like structure. Here, a type of D-shaped fiber (DF)-buried Mo2C saturable absorber (SA) fabricated by magnetron-sputtering deposition (MSD) and sol–gel technique is reported. The Mo2C material was buried between the bottom DF and the upper amorphous silica fabricated by sol–gel technology. Therefore, the DF-based SA effectively solves the problem of material shedding and aging, thus improving the stability and damage threshold of the fiber laser. Application of the SA in erbium-doped fiber laser and stable passive Q-switched operation with a maximum pulse energy of 430.47 nJ is realized. By adjusting the polarization state and pump power, high-power mode-locked pulses are generated with a pulse duration and output power of 199 fs and 54.13 mW, respectively. Further, bound-state soliton pulses are obtained with a pulse width of 312 fs and soliton interval of 1.26 ps for the first time based on MXene materials. Moreover, by application of the SA in ytterbium-doped fiber lasers, a stable dissipative soliton mode-locked pulse is obtained with a pulse width of 23 ps. These results indicate that the DF-based buried Mo2C as a novel SA provides a reliable method for all-fiber and multifunctional high-power ultrafast laser.
- 19 June 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (26) , 29625-29630
Passively Mode-Locked Fiber Laser with WS2/SiO2 Saturable Absorber Fabricated by Sol–Gel Technique
High-performance ultrafast fiber lasers require saturable absorbers (SAs) of high optical damage threshold and high operation stability. Here, the optical properties and application of the WS2/SiO2 SA prepared by the sol–gel method are reported. SiO2 prepared by sol–gel technique has similar properties to fiber in ultrafast fiber lasers, such as mechanical strength, refractive index, optical transmission, and absorption. For the SA device by the sol–gel method combined with WS2 material, not only will the additional scattering loss not be introduced, but also, the damage threshold of the SA device can be effectively increased. Furthermore, SA material is wrapped by SiO2, which insulates the influence of the external environment. Based on the first preparation of the WS2/SiO2 glass SA, stable soliton pulses are obtained in ytterbium-doped fiber lasers (YDFLs) with a pulse width of 58 ps, an average output power of 56.8 mW, and a repetition rate of 19.03 MHz. In addition, a stable mode-locked operation with a pulse width of 325 fs and an output power of 39.6 mW is also achieved in an erbium-doped fiber laser (EDFL). These results demonstrate that the WS2/SiO2 glass prepared by the sol–gel method can significantly increase laser output power and shorten pulse width in the fiber laser, which provides a new opportunity for the traditional preparation method of the SA device.
- 19 June 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (26) , 29625-29630
Passively Mode-Locked Fiber Laser with WS2/SiO2 Saturable Absorber Fabricated by Sol–Gel Technique
High-performance ultrafast fiber lasers require saturable absorbers (SAs) of high optical damage threshold and high operation stability. Here, the optical properties and application of the WS2/SiO2 SA prepared by the sol–gel method are reported. SiO2 prepared by sol–gel technique has similar properties to fiber in ultrafast fiber lasers, such as mechanical strength, refractive index, optical transmission, and absorption. For the SA device by the sol–gel method combined with WS2 material, not only will the additional scattering loss not be introduced, but also, the damage threshold of the SA device can be effectively increased. Furthermore, SA material is wrapped by SiO2, which insulates the influence of the external environment. Based on the first preparation of the WS2/SiO2 glass SA, stable soliton pulses are obtained in ytterbium-doped fiber lasers (YDFLs) with a pulse width of 58 ps, an average output power of 56.8 mW, and a repetition rate of 19.03 MHz. In addition, a stable mode-locked operation with a pulse width of 325 fs and an output power of 39.6 mW is also achieved in an erbium-doped fiber laser (EDFL). These results demonstrate that the WS2/SiO2 glass prepared by the sol–gel method can significantly increase laser output power and shorten pulse width in the fiber laser, which provides a new opportunity for the traditional preparation method of the SA device.
- 27 January 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (8) , 9404-9408
Molybdenum Disulfide Film Saturable Absorber Based on Sol–Gel Glass and Spin-Coating Used in High-Power Q-Switched Nd:YAG Laser
In recent years, many different kinds of nonlinear optical materials have been applied to passively Q-switched solid-state lasers. However, the average output powers of these lasers are typically limited to than one Watt due to low damage threshold of the materials. In this study, a molybdenum-disulfide-doped glass-composite absorber was synthesized using the sol-gel method and spin coating technique. The optical damage threshold of the absorber reached 3.17 J/cm2. Saturation intensity, modulation depth, and non-saturable loss are 9.35 MW/cm2, 8.41%, and 9.14%, respectively. After inserting the absorber into a linear Nd:YAG laser cavity. Maximum average output-power (3.22 W) and stable Q-switched laser pulses duration (132 ns) are obtained.
- 27 January 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (8) , 9404-9408
Molybdenum Disulfide Film Saturable Absorber Based on Sol–Gel Glass and Spin-Coating Used in High-Power Q-Switched Nd:YAG Laser
In recent years, many different kinds of nonlinear optical materials have been applied to passively Q-switched solid-state lasers. However, the average output powers of these lasers are typically limited to than one Watt due to low damage threshold of the materials. In this study, a molybdenum-disulfide-doped glass-composite absorber was synthesized using the sol-gel method and spin coating technique. The optical damage threshold of the absorber reached 3.17 J/cm2. Saturation intensity, modulation depth, and non-saturable loss are 9.35 MW/cm2, 8.41%, and 9.14%, respectively. After inserting the absorber into a linear Nd:YAG laser cavity. Maximum average output-power (3.22 W) and stable Q-switched laser pulses duration (132 ns) are obtained.
- 18 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (1) , 3-6
$1.34~\mu$ m Q-Switched Nd:YVO 4 Laser Based on Perovskite Film Saturable Absorber
Hybrid organic-inorganic methylammonium lead halide (CH3NH3PbI3) perovskite with a direct band gap has emerged as a material in the development of optoelectronic devices. Here, for the first time, at 1.34 lm, we fabricated CH3NH3PbI3 perovskite film saturable absorbers by spin coating methods for passively Q-switched Nd:YVO4 laser. The CH3NH3PbI3-SA shows a damage threshold of 276.6 mJ/cm2, a modulation depth of 18.2%, and a considerably low saturation intensity of 140.7 KW/cm2. By using CH3NH3PbI3-SA, a stable Q-switched laser with a maximum average output power of 182 mW and a pulse width of 181.6 ns can be obtained. These results reveal the promising application of CH3NH3PbI3 in 1.34 lm-lasers, optical switches or optical modulators.
- 18 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (1) , 3-6
$1.34~\mu$ m Q-Switched Nd:YVO 4 Laser Based on Perovskite Film Saturable Absorber
Hybrid organic-inorganic methylammonium lead halide (CH3NH3PbI3) perovskite with a direct band gap has emerged as a material in the development of optoelectronic devices. Here, for the first time, at 1.34 lm, we fabricated CH3NH3PbI3 perovskite film saturable absorbers by spin coating methods for passively Q-switched Nd:YVO4 laser. The CH3NH3PbI3-SA shows a damage threshold of 276.6 mJ/cm2, a modulation depth of 18.2%, and a considerably low saturation intensity of 140.7 KW/cm2. By using CH3NH3PbI3-SA, a stable Q-switched laser with a maximum average output power of 182 mW and a pulse width of 181.6 ns can be obtained. These results reveal the promising application of CH3NH3PbI3 in 1.34 lm-lasers, optical switches or optical modulators.
- 17 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (14) , 1167-1170
Er-Doped Q-Switched Fiber Laser Based on MoS2-SAM Fabricated by Langmuir-Blodgett (LB) Technique
In this letter, a Q-switched linear-cavity Er-doped fiber laser was prepared using a reflective molybdenum disulfide saturable absorber mirror (MoS 2 -SAM). MoS 2 -SAM with high uniformity and compactness was prepared using Langmuir-Blodgett (LB) technology. Films as thin as single molecule can be fabricated by LB technology under suitable conditions and thus, the nonsaturable losses of absorbers can be decreased. The modulation depth of MoS 2 -SAM is 9.8%. By inserting MoS 2 -SAM in Er-doped fiber lasers, a stable passive Q-switched operation was achieved with repetition rate ranging from 46.21 to 215.45 kHz and pulse duration ranging from 1316 to 319 ns. Under a maximum pump power of 500 mW, the laser still works stably with an average output power of 7.37 mW and a signal-to-noise ratio of 58 dB. Notably, the minimum pulse width is as narrow as 319 ns. This shows that LB method is a practical method to improve the performance of saturable absorbers.
- 17 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 31 (14) , 1167-1170
Er-Doped Q-Switched Fiber Laser Based on MoS2-SAM Fabricated by Langmuir-Blodgett (LB) Technique
In this letter, a Q-switched linear-cavity Er-doped fiber laser was prepared using a reflective molybdenum disulfide saturable absorber mirror (MoS 2 -SAM). MoS 2 -SAM with high uniformity and compactness was prepared using Langmuir-Blodgett (LB) technology. Films as thin as single molecule can be fabricated by LB technology under suitable conditions and thus, the nonsaturable losses of absorbers can be decreased. The modulation depth of MoS 2 -SAM is 9.8%. By inserting MoS 2 -SAM in Er-doped fiber lasers, a stable passive Q-switched operation was achieved with repetition rate ranging from 46.21 to 215.45 kHz and pulse duration ranging from 1316 to 319 ns. Under a maximum pump power of 500 mW, the laser still works stably with an average output power of 7.37 mW and a signal-to-noise ratio of 58 dB. Notably, the minimum pulse width is as narrow as 319 ns. This shows that LB method is a practical method to improve the performance of saturable absorbers.
- 1 July 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 103, 354-358
Generation of dark solitons in Er-doped fiber laser based on ferroferric-oxide nanoparticles
- 1 July 2018
- Published by Elsevier in Optics & Laser Technology
- Vol. 103, 354-358
Generation of dark solitons in Er-doped fiber laser based on ferroferric-oxide nanoparticles