DBDavid R. Boris

David R. Boris

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


David R. Boris has a total of 96 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Understanding the influence of plasma conditions on morphological evolution during plasma-enhanced atomic layer deposition of InN using in situ synchrotron x-ray scattering

    by Henry H. Chuang, Neeraj Nepal, David R. Boris, Scooter D. Johnson, Virginia R. Anderson, Alexander C. Kozen, Zachary R. Robinson, Scott G. Walton, Charles R. Eddy, Karl F. Ludwig, et al.

    Plasma-enhanced atomic layer deposition (PEALD) enables the growth of crystalline films of atomically precise thickness at reduced temperatures through the utilization of reactive and energetic plasma species. However, the mechanisms by which plasma-generated species influence nanoscale surface evolution during growth remain poorly understood. Here, we correlate the real-time evolution of nanoscale island morphology, including nucleation, coarsening, and coalescence, with the fluxes of reactive and energetic plasma species during PEALD growth. Grazing-incidence small-angle X-ray scattering was used as a nondestructive, surface-sensitive technique to monitor morphological evolution in real time, combined with plasma diagnostics to quantify reactive species and ion fluxes. We find that increasing reactive nitrogen flux accelerates the onset of island formation, while increasing ion flux promotes island coalescence and coarsening. These observations demonstrate how reactive species and ion fluxes modify nucleation, coalescence, and coarsening during PEALD growth. Furthermore, controlling reactive and energetic plasma species provides a means for tailoring surface processes and optimizing material properties during low-temperature thin-film growth.

  • In situ spectroscopic ellipsometry for atomic layer processes on III–V interfaces using critical points

    by John P. Murphy, Glenn G. Jernigan, Michael J. Johnson, David R. Boris, Scott G. Walton, Jill A. Nolde

    Plasma-enhanced atomic layer processing of III–V semiconductors requires precise control of plasma–surface interactions to achieve clean oxide-free interfaces, but conventional characterization methods are too slow to guide rapid process optimization. This work demonstrates an in situ spectroscopic ellipsometry methodology used as a rapid, model-light probe of III–V surface quality during plasma exposure. Monitoring the amplitude of the E0′ critical point from the pseudodielectric function is used as a metric of surface cleanliness. This methodology is demonstrated with Ar and Ar:H2 plasmas where the behavior of the E0′ amplitude is correlated with InAs surface modification using x-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). We observe an increase in E0′ with the removal of arsenic oxides in both plasmas that is confirmed by XPS and AFM roughness maps indicating that the response is dominated by interface chemistry rather than morphology. In Ar:H2 plasmas, E0′ transients exhibit an initial increase followed by a roll-over that marks the onset of metallic indium formation, which appears to be more sensitive to the presence of metallic indium on the surface than XPS. The methodology defines practical process boundaries in an accelerated manner when compared to the typical characterization process flows involving systematic characterization of large sample sets using time-intensive techniques such as XPS and AFM. Simplifying ellipsometric tracking of a small set of critical-point metrics in situ provides real-time feedback and aids in down-selection within large plasma parameter spaces and enables rapid optimization of plasma surface treatments in atomic layer processing.

  • Open Access

    Modeling remote inductively coupled plasmas for plasma-enhanced atomic layer deposition

    by Mackenzie E Meyer, David R Boris, Michael J Johnson, Mark J Kushner, Scott G Walton

    Remote inductively coupled plasmas (ICPs) are utilized in atomic precision processing as they provide the requisite flux of reactive and energetic species. Their remote nature helps mitigate damage to the substrate by energetic ions and photons produced in the plasma. However, the attributes of these plasma sources are not well characterized, particularly in the spatial afterglow where the growth substrate is located. This work focuses on modeling a commercially available remote ICP source with a 2D hybrid plasma model in pure Ar. The results of the model are benchmarked against spatially resolved Langmuir probe measurements in Ar and achieve good agreement with the measurements in the afterglow for a variety of operating conditions. The benchmarked results provide confidence in the model, which can then be used to better understand the physics in the spatial afterglow. In the remote ICP system, capacitive power coupling plays a large role in determining the plasma properties in the spatial afterglow, where a small amount of capacitive power coupling is responsible for elevated electron density, plasma potential, and electron temperature. These results are discussed in the context of atomic layer deposition (ALD). While this work discusses pure Ar plasmas, capacitive power coupling in the afterglow will affect mixtures with molecular gases used in ALD.

  • Open Access

    Thermal and mechanical behavior of plasma-synthesized, nanometer scale aluminum fluoride passivation layers

    by Mohsen Motezaker, Andrew H. Jones, David R. Boris, Scott G. Walton, Patrick E. Hopkins

    Aluminum is highly valued in ultraviolet (UV) optics for its exceptional reflectivity at wavelengths as short as 90 nm, but its effectiveness is compromised by rapid formation of a native oxide layer that reduces its UV reflectivity. To mitigate this issue, fluorine-containing protective layers, such as aluminum fluoride, are applied to inhibit oxidation while maintaining high transmission rates. Additionally, an aluminum fluoride layer serves as an effective barrier coating in advanced lithium-ion battery designs, preventing failures like significant temperature increases and thermal runaway. Despite these important applications, the thermal and mechanical properties of aluminum fluoride thin films have not been thoroughly investigated. In this study, optical pump–probe techniques are used to measure the thermal conductivity and elastic moduli of aluminum fluoride passivation layers with thicknesses ranging from 4 to 48 nm. The passivation layers are produced using a plasma-based process that removes the native oxide while converting the aluminum into aluminum fluoride. The results show that both thermal conductivity and elastic moduli increase with film thickness, indicating a thickness-dependent change in physico-chemical composition. Energy-dispersive x-ray spectroscopy reveals that thicker layers contain a higher proportion of fluorine relative to aluminum. Moreover, x-ray photoelectron spectroscopy and infrared variable-angle spectroscopic ellipsometry indicate that the chemical structure stabilizes in thicker samples, confirming the formation of AlF3. These findings provide valuable insights into the process–structure–property relationships of plasma-produced fluorinated layers, which are critical for optimizing UV optical coatings and enhancing lithium-ion battery safety.

  • Electron beam generated ion-ion plasmas produced in Ar/SF6 and Ar/NF3 mixtures for plasma anodization

    by David R. Boris, Michael J. Johnson, Virginia D. Wheeler, Maria Gabriela Sales, Luis V. Rodriguez de Marcos, Edward J. Wollack, Manuel A. Quijada, Scott G. Walton

    In this work, electron beam generated plasmas in Ar/SF6 and Ar/NF3 mixtures are used to form ion-ion plasmas from which one can extract F− ions. These negative ions are used to controllably fluorinate the surface of an aluminum substrate with nanoscale precision. To understand this process, the ion-ion plasmas are characterized with Langmuir probes and optical emission spectroscopy, and the resulting AlF3 layer is characterized using in situ spectroscopic ellipsometry and ex situ x-ray photoelectron spectroscopy with depth profiling. This combination of plasma and material characterization indicates that the fluoride layer formation process is similar to plasma anodization. Here, the flux of negative ions delivered to the surface combined with an applied bias that promotes the migration of F− ions into the substrate where they react to form AlF3, enabling the growth of thick fluoride layers. The minimum thickness of the resulting AlF3 layer is determined by the thickness of the resident native oxide layer on the aluminum surface, as the conversion of this layer from oxide to fluoride is necessary for the production of stoichiometric AlF3 films. It is found that converting the native oxide layer into a fluoride results in an expansion of the surface passivation layer thickness by about a factor of 2. It is also found that NF3 produces significantly higher densities of atomic F and F− compared to SF6, leading to more rapid growth of the AlF3 layer.


  • Effect of plasma parameters on the properties of V2O5 deposited by plasma-enhanced atomic layer deposition

    by P. M. Litwin, N. Nepal, M. G. Sales, D. R. Boris, M. J. Johnson, S. G. Walton, V. D. Wheeler

    In this work, we investigate the deposition of VOx thin films by plasma-enhanced atomic layer deposition. Specifically, we focus on the effects of the plasma operating conditions, including applied power, O2/Ar gas flow ratio, pressure, and coupling mode on the resulting thin film crystallinity and stoichiometry. In addition, we characterize the plasma and correlate the findings to the changes observed in the produced VOx thin films. The majority of conditions investigated yield crystalline V2O5. However, by increasing the pressure during the plasma half cycle, the V2O5 film can be deposited with a reduction in the crystalline character without any significant changes in stoichiometry. Langmuir probe measurements reveal that both the ion flux and plasma potential decrease with increasing pressure during the plasma step, which results in a corresponding drop in the energy flux density and ion energy delivered to the surface of the thin film. Analysis of the various plasma conditions investigated shows that increasing the pressure uniquely resulted in a decrease in the energy flux density and ion energy below a critical barrier necessary for complete crystallization of the deposited VOx films.

  • Open Access

    Spatiotemporal analysis of a short pulse argon plasma submerged in water

    by Michael James Johnson, David R Boris, Tz B Petrova, M E Meyer, Scott G Walton

    Atmospheric pressure plasmas create a unique chemical and electrical environment that is well-suited for the treatment of liquids. These plasmas can operate in a nonthermal regime when driven by pulsed power of sufficiently short duration to prevent significant heating of the surrounding gas, thus providing unique opportunities in liquid decontamination and remediation. This study investigates how varying the pulse width affects the properties of an argon plasma submerged in water. Plasmas produced using high-voltage (11 kV) pulses ranging from 50 to 350 ns at a frequency of 1 kHz were studied using electrical measurements and spatio-temporal optical emission spectroscopy. Results show that the plasma fills the gap between electrodes within the first 15 ns of the pulse. Once the gap closes, the voltage collapses and the current rises to a value determined by the power supply. The plasma remains in this current-limited state for the remainder of the pulse. Optical emission spectroscopy revealed that argon dominates the emission immediately after plasma formation, but over time, hydrogen emission becomes more prominent as the amount of dissociated water vapor in the plasma increases. Spatial emission profiles show uniform hydrogen emission across the reactor, whereas argon emission weakens near the positive electrode. Stark broadening analysis of hydrogen lines indicate a substantial electron density persists for several microseconds after the pulse, likely due to a small residual voltage on the electrodes associated with the power supply architecture. This post-pulse duration scales with pulse width and is found to last nearly 10 µs for the longest tested pulse width of 350 ns, highlighting not only the influence of pulse width on plasma dynamics but also showing the importance of other system parameters on determining the lifetime of the plasma.


  • Open Access

    Characterization of AlF3-passivated aluminum mirrors using non-contact thermal metrology

    by Andrew H. Jones, John T. Gaskins, Patrick E. Hopkins, Scott G. Walton, David R. Boris, John P. Murphy, Luis V. Rodriguez de Marcos, Javier Del Hoyo, Manuel A. Quijada

    We demonstrate the use of steady-state thermoreflectance (SSTR) as a technique for characterizing mirror surfaces. Due to the enhanced sensitivity of thermoreflectance compared to reflectance, SSTR provides the ability to assess the physical and chemical characteristics as well as the uniformity of thin films and coatings much more rapidly than common metrological methods such as x-ray photoelectron spectroscopy. The use of this technique is demonstrated on AlF3-passivated Al surfaces produced using a process developed for the fabrication of far ultraviolet reflectors. However, since SSTR is thermal in nature, this technique negates the need for a priori knowledge of the optical properties of the material. This is emphasized by interrogating both homogeneous and non-uniform AlF3 films.


  • Electrical Characterization of the Cycle-to-Cycle Repeatability of an Atmospheric Pressure Plasma Jet

    by Michael J. Johnson, David R. Boris, Tzvetelina B. Petrova, Scott G. Walton

    Atmospheric pressure plasma jets operate by projecting a streamer discharge toward remote substrates. The formation and propagation of streamers is an inherently stochastic process, which leads to cycle-to-cycle variations in streamer properties. The present work quantifies these variations through electrical measurements of a plasma jet striking a conductive substrate. It was found that streamer ignition and magnitude can change substantially from cycle to cycle and thus differ from time-averaged measurements taken over many cycles. For example, the energy required to drive the plasma jet and the amount of charge delivered to the substrate during a given cycle can vary from their respective averages by a factor of 2 or more. While some of this can be due to power supply stability, several other operating characteristics of the plasma jet were found to influence repeatability. It was found that helium and argon produced plasma jets with different levels of repeatability, with the repeatability of argon strongly dependent on the feed gas flow rate. Jets driven with pulsed-DC were notably more repeatable than those driven by a high-voltage sinewave. This is attributed to the difference in voltage rise time, which promotes more consistent ignition times. Increasing the voltage and frequency of the pulsed-DC plasma jet can further improve repeatability, where voltages above 2 kV and driving frequencies above 200 Hz significantly enhance the repeatability of the plasma jet.


  • Open Access

    Phase-shifted counterpropagating atmospheric pressure plasma jets: Characterization and interaction with materials

    by Michael J. Johnson, Gabriel H. Brown, David R. Boris, Tzvetelina B. Petrova, Scott G. Walton

    This study investigates the interaction between two counterpropagating atmospheric pressure plasma jets when their respective streamer ignition times are varied by introducing a phase difference between the AC waveforms used to generate them. When the plasma jets are driven in phase, the streamers form at approximately the same time, resulting in a dark region between the two jets. As the phase difference increases, this dark region shifts toward one of the electrodes. With a sufficiently large phase difference, this region vanishes, giving rise to a uniform plasma channel spanning the distance between the electrodes. High-speed imaging reveals that the interaction between the streamers within the channel reduces the streamer propagation length at intermediate phase differences. At large phase differences, the propagation distance of each streamer is enhanced due to the absence of the opposing streamer. Increasing the phase from 0° to 160° reduced the power consumption of the two jets by about 10%, while there was no significant change in the electron density or the N2 vibrational/rotational temperature. Finally, we show how phase-shifting enhances the interaction with three-dimensional objects located between the opposing jets, enabling the treatment of 3D substrates.