Luca Rovere
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Luca Rovere has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Pericle Zanchetta
Department of Electrical, Computer and Biomedical Engineering, University of Pavia, Pavia, Italy
9 shared publications - Andrea Formentini
University of Genova
5 shared publications - Jacopo Riccio
Power Electronics, Machine and Control Research Institute, University of Nottingham, Nottingham, U.K.
3 shared publications - Filippo Gemma
Department of Electrical, Computer and Biomedical Engineering, University of Pavia, Pavia, Italy
2 shared publications - Giovanni Lo Calzo
Ferrari, 87816 Maranello, Emilia-Romagna Italy
2 shared publications - Giulia Tresca
Department of Electrical, Computer and Biomedical Engineering, University of Pavia, Pavia, Italy
2 shared publications
Latest Publications
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. PP (00939994) , 1-10
Model-Predictive Control of Open-End Winding Synchronous Reluctance Motor Drives
This paper presents an advanced control strategy for a Synchronous Reluctance Machine (SyRel) in an Open-End Winding (OEW) configuration. The goal is to enhance performance and control flexibility in dual-inverter systems, which present strong multivariable interactions and nonlinear dynamics. To address these challenges, a Finite-Control-Set Model-Predictive Control (FCS-MPC) method is proposed, as it can directly handle multiple control objectives and system constraints within a unified framework. A single cost function is used to regulate motor torque, the auxiliary converter Floating Capacitor (FC) voltage, and the power factor at the main side. This enables coordinated control of both converters without cascaded loops. The predictive controller uses an experimentally identified magnetic model of the SyRel machine, which accounts for magnetic nonlinearities, improving prediction accuracy under dynamic response. Experimental validation confirms the effectiveness of the proposed strategy. The system shows fast dynamic response, robust regulation of control objectives, and consistent unity power factor at the main converter. A comparison with conventional PI-based control highlights the advantages of the proposed method in terms of power factor regulation and dynamic performance, particularly under strong nonlinearities introduced by the FC voltage control. These results confirm that the proposed cost function formulation, with its specific control terms, effectively enables regulation of the overall system.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. PP (00939994) , 1-10
Model-Predictive Control of Open-End Winding Synchronous Reluctance Motor Drives
This paper presents an advanced control strategy for a Synchronous Reluctance Machine (SyRel) in an Open-End Winding (OEW) configuration. The goal is to enhance performance and control flexibility in dual-inverter systems, which present strong multivariable interactions and nonlinear dynamics. To address these challenges, a Finite-Control-Set Model-Predictive Control (FCS-MPC) method is proposed, as it can directly handle multiple control objectives and system constraints within a unified framework. A single cost function is used to regulate motor torque, the auxiliary converter Floating Capacitor (FC) voltage, and the power factor at the main side. This enables coordinated control of both converters without cascaded loops. The predictive controller uses an experimentally identified magnetic model of the SyRel machine, which accounts for magnetic nonlinearities, improving prediction accuracy under dynamic response. Experimental validation confirms the effectiveness of the proposed strategy. The system shows fast dynamic response, robust regulation of control objectives, and consistent unity power factor at the main converter. A comparison with conventional PI-based control highlights the advantages of the proposed method in terms of power factor regulation and dynamic performance, particularly under strong nonlinearities introduced by the FC voltage control. These results confirm that the proposed cost function formulation, with its specific control terms, effectively enables regulation of the overall system.
- 14 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (2) , 3269-3278
Effects of the Floating Capacitor Voltage on the Torque-Speed Characteristic of an Open-End Winding Synchronous Reluctance Motor Drive
This manuscript investigates the torque-speed characteristics of a synchronous reluctance motor drive with an open-end winding (OEW) configuration. The machine is powered by standard two-level voltage source inverters (VSI), one supplied by a DC power source while the other connected to a floating capacitor (FC). The analysis considers the flux maps of a synchronous reluctance motor identified through experiments to account for the effect of the self-and cross-saturation phenomenon. The study reveals that the dual-inverter (DI) configuration with a FC can significantly extend the constant torque speed range and achieve unity power factor. In addition, the analysis demonstrates that the torque in the constant power speed range can be noticeably increased compared to the standard single-inverter (SI) configuration. With the full model of the OEW drive plant, the FC voltage can be purposefully selected to modify the drive torque speed characteristic to benefit the specific application. The advantages of the investigated synchronous drive architecture have been experimentally validated in different operating conditions with a purposely built set-up.
- 14 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (2) , 3269-3278
Effects of the Floating Capacitor Voltage on the Torque-Speed Characteristic of an Open-End Winding Synchronous Reluctance Motor Drive
This manuscript investigates the torque-speed characteristics of a synchronous reluctance motor drive with an open-end winding (OEW) configuration. The machine is powered by standard two-level voltage source inverters (VSI), one supplied by a DC power source while the other connected to a floating capacitor (FC). The analysis considers the flux maps of a synchronous reluctance motor identified through experiments to account for the effect of the self-and cross-saturation phenomenon. The study reveals that the dual-inverter (DI) configuration with a FC can significantly extend the constant torque speed range and achieve unity power factor. In addition, the analysis demonstrates that the torque in the constant power speed range can be noticeably increased compared to the standard single-inverter (SI) configuration. With the full model of the OEW drive plant, the FC voltage can be purposefully selected to modify the drive torque speed characteristic to benefit the specific application. The advantages of the investigated synchronous drive architecture have been experimentally validated in different operating conditions with a purposely built set-up.
- 9 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Model-Predictive Control of Open-End Winding Synchronous Reluctance Motor Drives
The aim of this manuscript is twofold. Firstly, it presents an analytical approach to study a synchronous reluctance motor drive configured in open-end winding. The intention is to identify the potential benefits of the floating capacitor configuration over the classical single inverter supply in terms of enlargement of the constant power speed range. A deep investigation was carried out on how varying the floating capacitor voltage level allows to modify the torque-versus-speed characteristics, enabling the drive to work at favorable operating points with high power factor. Secondly, the potential of the predictive control is exploited for such multi-variable system avoiding the non-trivial tuning difficulties necessary when standard controllers are considered, and allowing two converters to be controlled with a single cost function. Simulation results prove the desired operations with high power factor and extended constant torque region while keeping good dynamic performance.
- 9 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Model-Predictive Control of Open-End Winding Synchronous Reluctance Motor Drives
The aim of this manuscript is twofold. Firstly, it presents an analytical approach to study a synchronous reluctance motor drive configured in open-end winding. The intention is to identify the potential benefits of the floating capacitor configuration over the classical single inverter supply in terms of enlargement of the constant power speed range. A deep investigation was carried out on how varying the floating capacitor voltage level allows to modify the torque-versus-speed characteristics, enabling the drive to work at favorable operating points with high power factor. Secondly, the potential of the predictive control is exploited for such multi-variable system avoiding the non-trivial tuning difficulties necessary when standard controllers are considered, and allowing two converters to be controlled with a single cost function. Simulation results prove the desired operations with high power factor and extended constant torque region while keeping good dynamic performance.
- 6 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (5) , 4576-4586
Parameters and Volt–Ampere Ratings of a Floating Capacitor Open-End Winding Synchronous Motor Drive for Extended CPSR
This article proposes an analytical method for the selection of machine parameters and inverter power ratings of a synchronous motor operated in an open-end winding (OEW) configuration with one of the two voltage-source inverters (VSIs) connected to a floating capacitor (FC) in order to meet a specific torque–speed profile. With the derived normalized expressions and curves, all the suitable synchronous motors operated with an OEW-FC and a standard two-level VSI drive can be easily compared according to the power rating and desired speed–torque characteristic.
- 6 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (5) , 4576-4586
Parameters and Volt–Ampere Ratings of a Floating Capacitor Open-End Winding Synchronous Motor Drive for Extended CPSR
This article proposes an analytical method for the selection of machine parameters and inverter power ratings of a synchronous motor operated in an open-end winding (OEW) configuration with one of the two voltage-source inverters (VSIs) connected to a floating capacitor (FC) in order to meet a specific torque–speed profile. With the derived normalized expressions and curves, all the suitable synchronous motors operated with an OEW-FC and a standard two-level VSI drive can be easily compared according to the power rating and desired speed–torque characteristic.
- 2 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 56 (3) , 2709-2718
Electric Drive Based on an Open-End Winding Surface PM Synchronous Machine With a Floating Capacitor Bridge
A speed control scheme is presented for a 3-phase surface permanent magnet synchronous machine with an open-end stator winding fed by a three-phase inverter and a floating bridge inverter. The latter is used to compensate for the reactive power of the main inverter and to maximize the active power received by the motor, without exceeding the available stator current and DC-link voltage. To reduce the switching losses, the DC-link voltage of the floating inverter bridge varies depending on the operating condition of the motor and the controllability requirements of the system. The experimental results show that a significant improvement in the speed range at constant power is achievable, proportionally to the DC-link voltage of the floating bridge inverter.
- 2 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 56 (3) , 2709-2718
Electric Drive Based on an Open-End Winding Surface PM Synchronous Machine With a Floating Capacitor Bridge
A speed control scheme is presented for a 3-phase surface permanent magnet synchronous machine with an open-end stator winding fed by a three-phase inverter and a floating bridge inverter. The latter is used to compensate for the reactive power of the main inverter and to maximize the active power received by the motor, without exceeding the available stator current and DC-link voltage. To reduce the switching losses, the DC-link voltage of the floating inverter bridge varies depending on the operating condition of the motor and the controllability requirements of the system. The experimental results show that a significant improvement in the speed range at constant power is achievable, proportionally to the DC-link voltage of the floating bridge inverter.
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 6018-6025
Analysis and Detection of Electrical Aging Effects on High-Speed Motor Insulation
The use of fast wide-bandgap devices in high-speed electrical drives with steep pulsewidth modulation voltage waveforms is the main cause of increased stress on the electric machine insulation system and consequently, of reduced reliability of the whole system. This represents a major concern in safety-critical applications, such as in the aerospace and electric transportation fields. The novel contribution of this work is to assess the effects of electrical aging on complex insulation systems (i.e., a whole stator winding) by analyzing easily measurable macroscopic quantities. To this purpose, an electrical aging procedure is defined, and the effects produced on three tested motors are presented. Three different analysis methods are adopted with the aim of assessing the damage caused to an ac motor winding by such steep voltage waveforms and hence to evaluate the state of aging of the insulation system.
- 16 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 6018-6025
Analysis and Detection of Electrical Aging Effects on High-Speed Motor Insulation
The use of fast wide-bandgap devices in high-speed electrical drives with steep pulsewidth modulation voltage waveforms is the main cause of increased stress on the electric machine insulation system and consequently, of reduced reliability of the whole system. This represents a major concern in safety-critical applications, such as in the aerospace and electric transportation fields. The novel contribution of this work is to assess the effects of electrical aging on complex insulation systems (i.e., a whole stator winding) by analyzing easily measurable macroscopic quantities. To this purpose, an electrical aging procedure is defined, and the effects produced on three tested motors are presented. Three different analysis methods are adopted with the aim of assessing the damage caused to an ac motor winding by such steep voltage waveforms and hence to evaluate the state of aging of the insulation system.
- 25 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 7813-7821
Zero-Sequence Voltage Elimination for Dual-Fed Common DC-Link Open-End Winding PMSM High-Speed Starter-Generator—Part II: Deadtime Hysteresis Control of Zero-Sequence Current
In a common dc link dual-fed Open-End Winding Permanent Magnet Synchronous Motor (OEW-PMSM) topology it is well known how the additional flow of a Zero-Sequence Current (ZSC) is permitted. The low Zero-Sequence Impedance (ZSI) characteristic of high speed machines leads to high intensity and high frequency ripple of the ZSC. Therefore there is the necessity to eliminate the Zero-Sequence-Voltage (ZSV) produced by the two Voltage Source Converters (VSCs) that feed the machine. Furthermore the non-sinusoidal back Electro Magnetic Force (back EMF) causes the circulation of a third harmonic ZSC. An OEW-PMSM high speed starter-generator fed by a dual-inverter with single dc link is considered. Part I of this work proposes a modulation for the considered topology able to eliminate instantaneously the ZSV produced. In this paper a detailed analysis of the Dead Time (DT) effect on the ZSV has been carried out and a novel hysteresis control for the ZSC using the DT as a control action is presented. The DT produces a ZSV distortion on the zero axis that can be used to control the third harmonic ZSC flowing due to the non-sinusoidal machine back EMF.
- 25 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 7813-7821
Zero-Sequence Voltage Elimination for Dual-Fed Common DC-Link Open-End Winding PMSM High-Speed Starter-Generator—Part II: Deadtime Hysteresis Control of Zero-Sequence Current
In a common dc link dual-fed Open-End Winding Permanent Magnet Synchronous Motor (OEW-PMSM) topology it is well known how the additional flow of a Zero-Sequence Current (ZSC) is permitted. The low Zero-Sequence Impedance (ZSI) characteristic of high speed machines leads to high intensity and high frequency ripple of the ZSC. Therefore there is the necessity to eliminate the Zero-Sequence-Voltage (ZSV) produced by the two Voltage Source Converters (VSCs) that feed the machine. Furthermore the non-sinusoidal back Electro Magnetic Force (back EMF) causes the circulation of a third harmonic ZSC. An OEW-PMSM high speed starter-generator fed by a dual-inverter with single dc link is considered. Part I of this work proposes a modulation for the considered topology able to eliminate instantaneously the ZSV produced. In this paper a detailed analysis of the Dead Time (DT) effect on the ZSV has been carried out and a novel hysteresis control for the ZSC using the DT as a control action is presented. The DT produces a ZSV distortion on the zero axis that can be used to control the third harmonic ZSC flowing due to the non-sinusoidal machine back EMF.
- 25 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 7804-7812
Zero-Sequence Voltage Elimination for Dual-Fed Common DC-Link Open-End Winding PMSM High-Speed Starter–Generator—Part I: Modulation
In this paper a dual-fed common dc-link topology Open-End Winding Permanent Magnet Synchronous Motor (OEW-PMSM) for aircraft high speed Starter-Generator application is considered. While on one hand the common dc bus configuration significantly simplifies and reduces the costs of the topology, on the other hand it allows the Zero-Sequence Current (ZSC) to flow freely in the system. High speed machines are characterized by low phase inductance which implies low Zero-Sequence Impedance (ZSI). A small time constant of the zero-sequence circuit produces a high frequency, high intensity ZSC ripple with the risk of harming the switching devices. This paper presents a novel hybrid Space Vector - Pulse Width Modulation (SVPWM) that allows to instantaneously eliminate the Zero-Sequence Voltage (ZSV) produced by the two Voltage Source Converters (VSCs) by square wave modulating one of the two VSCs. The non-sinusoidal machine back Electro Magnetic Force (back EMF) has been considered and an analysis of the converters' Dead Time (DT) effect on the ZSV has been carried out. The square wave modulated VSC uses IGBT devices while the other uses SiC technology. The proposed topology is tested through both simulations and experiments.
- 25 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 55 (6) , 7804-7812
Zero-Sequence Voltage Elimination for Dual-Fed Common DC-Link Open-End Winding PMSM High-Speed Starter–Generator—Part I: Modulation
In this paper a dual-fed common dc-link topology Open-End Winding Permanent Magnet Synchronous Motor (OEW-PMSM) for aircraft high speed Starter-Generator application is considered. While on one hand the common dc bus configuration significantly simplifies and reduces the costs of the topology, on the other hand it allows the Zero-Sequence Current (ZSC) to flow freely in the system. High speed machines are characterized by low phase inductance which implies low Zero-Sequence Impedance (ZSI). A small time constant of the zero-sequence circuit produces a high frequency, high intensity ZSC ripple with the risk of harming the switching devices. This paper presents a novel hybrid Space Vector - Pulse Width Modulation (SVPWM) that allows to instantaneously eliminate the Zero-Sequence Voltage (ZSV) produced by the two Voltage Source Converters (VSCs) by square wave modulating one of the two VSCs. The non-sinusoidal machine back Electro Magnetic Force (back EMF) has been considered and an analysis of the converters' Dead Time (DT) effect on the ZSV has been carried out. The square wave modulated VSC uses IGBT devices while the other uses SiC technology. The proposed topology is tested through both simulations and experiments.
- 10 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 66 (5) , 3731-3741
FPGA Implementation of a Novel Oversampling Deadbeat Controller for PMSM Drives
This paper presents a novel Oversampling DeadBeat (OS-DB) current control approach for Permanent Magnet Synchronous Motors (PMSMs) drives capable of operating at a controller sampling frequency multiple of the power converter switching frequency. Model based controllers suffer form heavy computational demand and performance degradation due to parameters uncertainties. The proposed controller concurrently with FPGA implementation permits to achieve a constant switching frequency and an optimal current ripple along with a high current loop bandwidth and robust behaviour to parameters variation. A disturbance observer has been added to the proposed controller in order to compensate for the converter voltage distortions. The proposed control strategy is tested through both simulations and experiments.
- 10 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 66 (5) , 3731-3741
FPGA Implementation of a Novel Oversampling Deadbeat Controller for PMSM Drives
This paper presents a novel Oversampling DeadBeat (OS-DB) current control approach for Permanent Magnet Synchronous Motors (PMSMs) drives capable of operating at a controller sampling frequency multiple of the power converter switching frequency. Model based controllers suffer form heavy computational demand and performance degradation due to parameters uncertainties. The proposed controller concurrently with FPGA implementation permits to achieve a constant switching frequency and an optimal current ripple along with a high current loop bandwidth and robust behaviour to parameters variation. A disturbance observer has been added to the proposed controller in order to compensate for the converter voltage distortions. The proposed control strategy is tested through both simulations and experiments.