Franck Pourroy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Franck Pourroy has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Frédéric Vignat
Univ. Grenoble Alpes, CNRS, Grenoble INP*, G-SCOP, Grenoble, France
4 shared publications - Mouhamadou Mansour Mbow
Hexagon, Grenoble, France
3 shared publications - Philippe Marin
MHA Laboratory, Grenoble School of Architecture (ENSAG), Univ. Grenoble Alpes (UGA), Grenoble, France
3 shared publications - Nicolas Perry
University of Bordeaux, CNRS, Bordeaux INP, I2M, UMR 5295
2 shared publications Philippe Marin
Univ. Grenoble Alpes, CNRS, Grenoble INP, G-SCOP, Grenoble, France
2 shared publicationsB. Trébucq
Centre de recherches
1 shared publication
Latest Publications
- Open Access
- 27 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 131 (2) , 797-815
Evaluation of a decision-support tool for part orientation in EBM additive manufacturing
- 27 September 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 131 (2) , 797-815
Open AccessEvaluation of a decision-support tool for part orientation in EBM additive manufacturing
- 25 September 2022
- Published by Springer Nature
- p. 569-580
Real-Time Approximative Thermal Simulation for Wire Arc Additive Manufacturing
- 25 September 2022
- Published by Springer Nature
- p. 569-580
Real-Time Approximative Thermal Simulation for Wire Arc Additive Manufacturing
- 22 April 2021
- Published by Wiley in Computer Graphics Forum
- Vol. 40 (6) , 215-241
An Efficient Hybrid Optimization Strategy for Surface Reconstruction
An efficient surface reconstruction strategy is presented in this study, which is able to approximate non‐convex sets of target points (TPs). The approach is split in two phases: (a) the mapping phase, making use of the shape preserving method (SPM) to get a proper parametrization of each sub‐domain composing the TPs set; (b) the fitting phase, where each patch is fitted by means of a suitable non‐uniform rational basis spline (NURBS) surface by considering, as design variables, all parameters involved in its definition. To this purpose, the surface fitting problem is formulated as a constrained non‐linear programming problem (CNLPP) defined over a domain having changing dimension, wherein both the number and the value of the design variables are optimized. To deal with this CNLPP, the optimization process is split in two steps. Firstly, a special genetic algorithm (GA) optimizes both the value and the number of design variables by means of a two‐level evolution strategy (species and individuals). Secondly, the solution provided by the GA constitutes the initial guess for the deterministic optimization, which aims at improving the accuracy of the fitting surfaces. The effectiveness of the proposed methodology is proven through some meaningful benchmarks taken from the literature.
- 22 April 2021
- Published by Wiley in Computer Graphics Forum
- Vol. 40 (6) , 215-241
An Efficient Hybrid Optimization Strategy for Surface Reconstruction
An efficient surface reconstruction strategy is presented in this study, which is able to approximate non‐convex sets of target points (TPs). The approach is split in two phases: (a) the mapping phase, making use of the shape preserving method (SPM) to get a proper parametrization of each sub‐domain composing the TPs set; (b) the fitting phase, where each patch is fitted by means of a suitable non‐uniform rational basis spline (NURBS) surface by considering, as design variables, all parameters involved in its definition. To this purpose, the surface fitting problem is formulated as a constrained non‐linear programming problem (CNLPP) defined over a domain having changing dimension, wherein both the number and the value of the design variables are optimized. To deal with this CNLPP, the optimization process is split in two steps. Firstly, a special genetic algorithm (GA) optimizes both the value and the number of design variables by means of a two‐level evolution strategy (species and individuals). Secondly, the solution provided by the GA constitutes the initial guess for the deterministic optimization, which aims at improving the accuracy of the fitting surfaces. The effectiveness of the proposed methodology is proven through some meaningful benchmarks taken from the literature.
- 3 January 2021
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 33 (5) , 1209-1227
Mathematization of experts knowledge: example of part orientation in additive manufacturing
- 3 January 2021
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 33 (5) , 1209-1227
Mathematization of experts knowledge: example of part orientation in additive manufacturing
- 3 September 2020
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 14 (4) , 1159-1170
Eight action rules for the orientation of additive manufacturing parts in powder bed fusion: an industry practice
- 3 September 2020
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 14 (4) , 1159-1170
Eight action rules for the orientation of additive manufacturing parts in powder bed fusion: an industry practice
- 2 January 2020
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 5 (2) , 139-152
Extruded diameter dependence on temperature and velocity in the fused deposition modeling process
- 2 January 2020
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 5 (2) , 139-152
Extruded diameter dependence on temperature and velocity in the fused deposition modeling process
- 24 January 2019
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 13 (1) , 295-308
Impacts of the settings in a design for additive manufacturing process based on topological optimization
- 24 January 2019
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 13 (1) , 295-308
Impacts of the settings in a design for additive manufacturing process based on topological optimization
- 1 March 1999
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 10 (1) , 61-71
Information structuring for use and reuse of mechanical analysis models in engineering design
- 1 March 1999
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 10 (1) , 61-71
Information structuring for use and reuse of mechanical analysis models in engineering design