Chan Soo Ha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chan Soo Ha has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Michael E. Plesha
5 shared publications- Roderic S. Lakes
University of Wisconsin, Madison, USA
5 shared publications Roderic S. Lakes
3 shared publications- Meng-Ting Hsieh2 shared publications
- Carlos Andrade
University of Wisconsin, Madison, WI, United States
1 shared publication Chenang Liu
Industrial Engineering and Management, Oklahoma State University, Stillwater, USA
1 shared publication
Latest Publications
- Top Cited PapersOpen Access
- 18 September 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-11
Rapid inverse design of metamaterials based on prescribed mechanical behavior through machine learning
Designing and printing metamaterials with customizable architectures enables the realization of unprecedented mechanical behaviors that transcend those of their constituent materials. These behaviors are recorded in the form of response curves, with stress-strain curves describing their quasi-static footprint. However, existing inverse design approaches are yet matured to capture the full desired behaviors due to challenges stemmed from multiple design objectives, nonlinear behavior, and process-dependent manufacturing errors. Here, we report a rapid inverse design methodology, leveraging generative machine learning and desktop additive manufacturing, which enables the creation of nearly all possible uniaxial compressive stress‒strain curve cases while accounting for process-dependent errors from printing. Results show that mechanical behavior with full tailorability can be achieved with nearly 90% fidelity between target and experimentally measured results. Our approach represents a starting point to inverse design materials that meet prescribed yet complex behaviors and potentially bypasses iterative design-manufacturing cycles.
- 18 September 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-11
Top Cited PapersOpen AccessRapid inverse design of metamaterials based on prescribed mechanical behavior through machine learning
Designing and printing metamaterials with customizable architectures enables the realization of unprecedented mechanical behaviors that transcend those of their constituent materials. These behaviors are recorded in the form of response curves, with stress-strain curves describing their quasi-static footprint. However, existing inverse design approaches are yet matured to capture the full desired behaviors due to challenges stemmed from multiple design objectives, nonlinear behavior, and process-dependent manufacturing errors. Here, we report a rapid inverse design methodology, leveraging generative machine learning and desktop additive manufacturing, which enables the creation of nearly all possible uniaxial compressive stress‒strain curve cases while accounting for process-dependent errors from printing. Results show that mechanical behavior with full tailorability can be achieved with nearly 90% fidelity between target and experimentally measured results. Our approach represents a starting point to inverse design materials that meet prescribed yet complex behaviors and potentially bypasses iterative design-manufacturing cycles.
- 15 February 2023
- Published by Elsevier in Mechanics Research Communications
- Vol. 128
The effect of geometric imperfections on the mechanical response of isotropic closed-cell plate lattices
- 15 February 2023
- Published by Elsevier in Mechanics Research Communications
- Vol. 128
The effect of geometric imperfections on the mechanical response of isotropic closed-cell plate lattices
- Open Access
- 26 March 2021
- Published by Open Engineering Inc in engrXiv
The effect of geometric imperfections on the mechanical response of isotropic closed-cell plate-lattices
Cubic+octet plate-lattices, whose unit cell comprises plates aligned along simple-cubic and face-centered-cubic planes of crystal structures, have attracted scientists and engineers because of their isotropic, near-optimal mass-specific performance that reaches theoretical upper bounds on stiffness and strength at low density. While their structural efficiency has been recently examined analytically, numerically and experimentally, their sensitivity to geometric imperfections has remained elusive. Here, using finite element simulations, we present sensitivity of the macroscopic mechanical properties of the plate-lattices to two types of geometric imperfections: namely, periodically distributed defects, characterizing plate waviness and displaced intersections, and randomly dispersed defects, representing missing plates, observed in their additively manufactured samples. Our results show that the randomly dispersed imperfections lead to a greater reduction in the Young’s modulus and yield strength than its counterpart across all relative densities under consideration, while their scaling relations with the relative density remains linear, confirming their structural efficiency attributed to stretching-dominated behavior even with the presence of the imperfections. This study sheds light on previously elusive sensitivity of the plate-lattices to the geometric imperfections and provides understanding of their defect-dependent mechanical performance.
- 26 March 2021
- Published by Open Engineering Inc in engrXiv
Open AccessThe effect of geometric imperfections on the mechanical response of isotropic closed-cell plate-lattices
Cubic+octet plate-lattices, whose unit cell comprises plates aligned along simple-cubic and face-centered-cubic planes of crystal structures, have attracted scientists and engineers because of their isotropic, near-optimal mass-specific performance that reaches theoretical upper bounds on stiffness and strength at low density. While their structural efficiency has been recently examined analytically, numerically and experimentally, their sensitivity to geometric imperfections has remained elusive. Here, using finite element simulations, we present sensitivity of the macroscopic mechanical properties of the plate-lattices to two types of geometric imperfections: namely, periodically distributed defects, characterizing plate waviness and displaced intersections, and randomly dispersed defects, representing missing plates, observed in their additively manufactured samples. Our results show that the randomly dispersed imperfections lead to a greater reduction in the Young’s modulus and yield strength than its counterpart across all relative densities under consideration, while their scaling relations with the relative density remains linear, confirming their structural efficiency attributed to stretching-dominated behavior even with the presence of the imperfections. This study sheds light on previously elusive sensitivity of the plate-lattices to the geometric imperfections and provides understanding of their defect-dependent mechanical performance.
- 1 December 2019
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 178-179, 127-135
Cubic negative stiffness lattice structure for energy absorption: Numerical and experimental studies
- 1 December 2019
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 178-179, 127-135
Cubic negative stiffness lattice structure for energy absorption: Numerical and experimental studies
- 23 November 2018
- Published by Wiley in Physica Status Solidi (b)
- Vol. 256 (1)
Flexible Cube Tilt Lattice with Anisotropic Cosserat Effects and Negative Poisson's Ratio
A 3D lattice structure consisting of pivoting cubes with flexible links at the corners is presented. It exhibits anisotropic negative Poisson's ratio −0.54 and −0.75. Size effects occur in torsion and bending; these effects are consistent with Cosserat elasticity but not with classical elasticity. Cosserat elastic solids exhibit sensitivity to strain gradients; size effects occur in torsion and bending; also reduction in stress concentrations. The observed Cosserat effects also reveal anisotropy.
- 23 November 2018
- Published by Wiley in Physica Status Solidi (b)
- Vol. 256 (1)
Flexible Cube Tilt Lattice with Anisotropic Cosserat Effects and Negative Poisson's Ratio
A 3D lattice structure consisting of pivoting cubes with flexible links at the corners is presented. It exhibits anisotropic negative Poisson's ratio −0.54 and −0.75. Size effects occur in torsion and bending; these effects are consistent with Cosserat elasticity but not with classical elasticity. Cosserat elastic solids exhibit sensitivity to strain gradients; size effects occur in torsion and bending; also reduction in stress concentrations. The observed Cosserat effects also reveal anisotropy.
- Open Access
- 7 April 2018
- Published by Mathematical Sciences Publishers in Journal of Mechanics of Materials and Structures
- Vol. 13 (1) , 93-101
Extreme Cosserat elastic cube structure with large magnitude of negative Poisson’s ratio
A structure consisting of pivoting cubes is presented. It has zero Young's modulus and zero bulk modulus. Poisson's ratio has large negative values in all directions; the structure exhibits anisotropy in Poisson's ratio. The structure is compliant in tension but rigid in torsion and bending. The Cosserat characteristic length tends to infinity.
- 7 April 2018
- Published by Mathematical Sciences Publishers in Journal of Mechanics of Materials and Structures
- Vol. 13 (1) , 93-101
Open AccessExtreme Cosserat elastic cube structure with large magnitude of negative Poisson’s ratio
A structure consisting of pivoting cubes is presented. It has zero Young's modulus and zero bulk modulus. Poisson's ratio has large negative values in all directions; the structure exhibits anisotropy in Poisson's ratio. The structure is compliant in tension but rigid in torsion and bending. The Cosserat characteristic length tends to infinity.
- 1 March 2018
- Published by Elsevier in Materials & Design
- Vol. 141, 426-437
Design, fabrication, and analysis of lattice exhibiting energy absorption via snap-through behavior
- 1 March 2018
- Published by Elsevier in Materials & Design
- Vol. 141, 426-437
Design, fabrication, and analysis of lattice exhibiting energy absorption via snap-through behavior
- 1 April 2017
- Published by Elsevier in Extreme Mechanics Letters
- Vol. 12, 101-107
Simulations of thermoelastic triangular cell lattices with bonded joints by finite element analysis
- 1 April 2017
- Published by Elsevier in Extreme Mechanics Letters
- Vol. 12, 101-107
Simulations of thermoelastic triangular cell lattices with bonded joints by finite element analysis
- 19 April 2016
- Published by Wiley in Physica Status Solidi (b)
- Vol. 253 (7) , 1243-1251
Chiral three‐dimensional isotropic lattices with negative Poisson's ratio
Chiral three‐dimensional isotropic cubic lattices with rigid cubical nodules and multiple deformable ribs are developed and analyzed via finite element analysis. The lattices exhibit geometry‐dependent Poisson's ratio that can be tuned to negative values. Poisson's ratio decreases from positive to negative values as the number of cells increases. Isotropy is obtained by adjustment of aspect ratio. The lattices exhibit significant size effects. Such a phenomenon cannot occur in a classical elastic continuum but it can occur in a Cosserat solid.
- 19 April 2016
- Published by Wiley in Physica Status Solidi (b)
- Vol. 253 (7) , 1243-1251
Chiral three‐dimensional isotropic lattices with negative Poisson's ratio
Chiral three‐dimensional isotropic cubic lattices with rigid cubical nodules and multiple deformable ribs are developed and analyzed via finite element analysis. The lattices exhibit geometry‐dependent Poisson's ratio that can be tuned to negative values. Poisson's ratio decreases from positive to negative values as the number of cells increases. Isotropy is obtained by adjustment of aspect ratio. The lattices exhibit significant size effects. Such a phenomenon cannot occur in a classical elastic continuum but it can occur in a Cosserat solid.
- Open Access
- 5 April 2016
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 25 (5) , 054005
Chiral three-dimensional lattices with tunable Poisson’s ratio
- 5 April 2016
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 25 (5) , 054005
Open AccessChiral three-dimensional lattices with tunable Poisson’s ratio