Sarah Van Erdeweghe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sarah Van Erdeweghe has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Johan Van Bael
8 shared publicationsBen Laenen
7 shared publicationsWilliam D'Haeseleer
3 shared publicationsWilliam D’hAeseleer
3 shared publicationsEric Van Den Bulck
Professor Applied Mechanics and Energy Conversion (TME) Section, Department of Mechanical Engineering, KU Leuven—University of Leuven, Leuven B-3001, Belgium
1 shared publication- Joris De Schutter
Department of Mechanical Engineering, KU Leuven, and Flanders Make@KU Leuven, Leuven, Belgium
1 shared publication
Latest Publications
- 1 October 2019
- Published by Elsevier in Energy Conversion and Management
- Vol. 198
Optimal configuration, design and control of a binary geothermal combined heat-and-power plant
- 1 October 2019
- Published by Elsevier in Energy Conversion and Management
- Vol. 198
Optimal configuration, design and control of a binary geothermal combined heat-and-power plant
- 1 May 2019
- Published by Elsevier in Applied Energy
- Vol. 242, 716-731
Design and off-design optimization procedure for low-temperature geothermal organic Rankine cycles
- 1 May 2019
- Published by Elsevier in Applied Energy
- Vol. 242, 716-731
Design and off-design optimization procedure for low-temperature geothermal organic Rankine cycles
- 1 October 2017
- Published by Elsevier in Renewable Energy
- Vol. 111, 494-505
Comparison of series/parallel configuration for a low-T geothermal CHP plant, coupled to thermal networks
- 1 October 2017
- Published by Elsevier in Renewable Energy
- Vol. 111, 494-505
Comparison of series/parallel configuration for a low-T geothermal CHP plant, coupled to thermal networks
- Open Access
- 1 September 2017
- Published by Elsevier in Energy Procedia
- Vol. 129, 10-17
Influence of the pinch-point-temperature difference on the performance of the Preheat-parallel configuration for a low-temperature geothermally-fed CHP
- 1 September 2017
- Published by Elsevier in Energy Procedia
- Vol. 129, 10-17
Open AccessInfluence of the pinch-point-temperature difference on the performance of the Preheat-parallel configuration for a low-temperature geothermally-fed CHP
- 1 June 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 142, 117-126
“Preheat-parallel” configuration for low-temperature geothermally-fed CHP plants
- 1 June 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 142, 117-126
“Preheat-parallel” configuration for low-temperature geothermally-fed CHP plants
- 6 June 2016
- Published by Wiley in Journal of Mechanical Design
- Vol. 138 (7) , 073401
Integral Modeling of a Twin-Screw Compressor
In this paper, an integral methodology for the modeling of a twin-screw compressor is presented. Starting from a known rotor profile, all the algorithms to calculate the second rotor profile, the size of the control volume, and the compressor's performance are presented. The proposed modeling approach can be applied in an optimization procedure to find the optimal rotor profiles for a given application, with corresponding working conditions. Furthermore, based on the modeling results and substantiated with measurements on different compressor types, a similarity law for positive displacement compressors seems to exist. The existence of a similarity law has large application potential as it could be used to predict the performance of a positive displacement compressor in other than the (lab) tested working conditions. Further investigation of the similarity law for positive displacement compressors is therefore proposed as a key topic for future research.
- 6 June 2016
- Published by Wiley in Journal of Mechanical Design
- Vol. 138 (7) , 073401
Integral Modeling of a Twin-Screw Compressor
In this paper, an integral methodology for the modeling of a twin-screw compressor is presented. Starting from a known rotor profile, all the algorithms to calculate the second rotor profile, the size of the control volume, and the compressor's performance are presented. The proposed modeling approach can be applied in an optimization procedure to find the optimal rotor profiles for a given application, with corresponding working conditions. Furthermore, based on the modeling results and substantiated with measurements on different compressor types, a similarity law for positive displacement compressors seems to exist. The existence of a similarity law has large application potential as it could be used to predict the performance of a positive displacement compressor in other than the (lab) tested working conditions. Further investigation of the similarity law for positive displacement compressors is therefore proposed as a key topic for future research.