Anne A. Campbell
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Anne A. Campbell has a total of 167 co-authors. Here are the top co-authors by number of shared publications:
- Yutai Katoh
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
8 shared publications - John D. Hunn
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
6 shared publications - Tyler Gerczak
ORNL
6 shared publications Yutai Katoh
Oak Ridge Natl Lab, Mat Sci & Technol Div, POB 2008, Oak Ridge, TN 37831 USA
6 shared publicationsBrian C. Jolly
Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
5 shared publicationsAustin T. Schumacher
Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
4 shared publications
Latest Publications
- Open Access
- 29 August 2026
- Published by Elsevier in SSRN Electronic Journal
Inelastic neutron scattering assessment of hydrogen residues in powder-derived hot-pressed graphite and commercial HOPG
Powder-derived graphite routes are attractive for scalable neutron-optics components, but binder/resin processing can leave hydrogen-containing residues after pyrolysis. Inelastic neutron scattering (INS) spectra were measured for a powder-derived hot-pressed graphite (HPG) sample and commercial highly oriented pyrolytic graphite (HOPG). The HPG was prepared from graphite powder, phenolic resin, and water by pressure assisted curing, pyrolysis at 900 ◦C, and pressure consolidation at 1800 ◦C. Both graphite samples were converted to powder-like specimens for INS measurements at 7 K. Neutron diffraction scans show that crushed HOPG retains strong preferred orientation, whereas HPG is closer to a powder average structure. The measured dynamical structure factors, S(Q,E), showgraphite phonon dispersion in HPG at energies below 220 meV and agree qualitatively with graphite simulations convoluted with the spectrometer resolution. A hydrogen-sensitive comparison, based on the mass-normalized intensity of the C–H stretching band around 350–400 meV, shows that the C–H stretching band intensity of commercial HOPG is approximately 1.45 times higher than that of HPG.A graphane-referenced calibration gives approximate hydrogen contents of 69 mass ppm for HPG and 100 mass ppm for HOPG. The pressure-consolidated binder/resin-derived HPG therefore does not exhibit an excess hydrogen-sensitive C–H stretching mode signalrelative to the commercial HOPG benchmark.
- 29 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInelastic neutron scattering assessment of hydrogen residues in powder-derived hot-pressed graphite and commercial HOPG
Powder-derived graphite routes are attractive for scalable neutron-optics components, but binder/resin processing can leave hydrogen-containing residues after pyrolysis. Inelastic neutron scattering (INS) spectra were measured for a powder-derived hot-pressed graphite (HPG) sample and commercial highly oriented pyrolytic graphite (HOPG). The HPG was prepared from graphite powder, phenolic resin, and water by pressure assisted curing, pyrolysis at 900 ◦C, and pressure consolidation at 1800 ◦C. Both graphite samples were converted to powder-like specimens for INS measurements at 7 K. Neutron diffraction scans show that crushed HOPG retains strong preferred orientation, whereas HPG is closer to a powder average structure. The measured dynamical structure factors, S(Q,E), showgraphite phonon dispersion in HPG at energies below 220 meV and agree qualitatively with graphite simulations convoluted with the spectrometer resolution. A hydrogen-sensitive comparison, based on the mass-normalized intensity of the C–H stretching band around 350–400 meV, shows that the C–H stretching band intensity of commercial HOPG is approximately 1.45 times higher than that of HPG.A graphane-referenced calibration gives approximate hydrogen contents of 69 mass ppm for HPG and 100 mass ppm for HOPG. The pressure-consolidated binder/resin-derived HPG therefore does not exhibit an excess hydrogen-sensitive C–H stretching mode signalrelative to the commercial HOPG benchmark.
- Open Access
- 9 March 2026
- Published by Elsevier in SSRN Electronic Journal
Characterizing Hydrogen-Bearing Residues During Phenolic Resin Pyrolysis in Graphite Using Inelastic Neutron Scattering
Graphite is widely used in neutron scattering instrumentation as monochromators, analyzers, and beam-conditioning optics, where mostly coherent neutron scattering of carbon is essential for their performance. However, advanced neutron-optics geometries increasingly require fabrication routes that rely on graphite powders and organic binders rather than conventionally grown monolithic pyrolytic graphite. In this work, we investigate a binder-assisted approach in which graphite powder is combined with a phenol–formaldehyde resol resin (Plenco 14670), cured, and pyrolyzed to form a shaped carbon body. Because phenolic resins contain significant hydrogen-bearing functional groups, a central question is whether the thermal treatment is sufficient to remove hydrogen to levels compatible with neutron applications. We address this by combining inelastic neutron scattering (INS) and quantitative vibrational analysis to determine the hydrogen concentration before and after pyrolysis. The C–H stretching features near ∼ 380 meV serve as sensitive markers of residual hydrogen. Our results show that pyrolysis at 900◦C reduces the hydrogen concentration by a factor of approximately 54.4× relative to the diluted resin, demonstrating substantial decomposition of the binder-derived organic component. Nevertheless, comparison with a graphite reference reveals measurable residual hydrogen in the pyrolyzed composite, indicating incomplete removal at this temperature. These findings establish the feasibility of binder-assisted graphite shaping for neutron optics while highlighting the need for higher-temperature pyrolysis or extended dwell times to achieve the ultra-low hydrogen levels required for high-performance neutron-scattering instrumentation. Notice of Copyright This manuscript has been authored by UT-Battelle, LLC under Contract No. DEAC05-00OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes. The Department of Energy will provide public access to these results of federally sponsored research in accordance with the DOE Public Access Plan (http://energy.gov/downloads/doe-public-access-plan).
- 9 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCharacterizing Hydrogen-Bearing Residues During Phenolic Resin Pyrolysis in Graphite Using Inelastic Neutron Scattering
Graphite is widely used in neutron scattering instrumentation as monochromators, analyzers, and beam-conditioning optics, where mostly coherent neutron scattering of carbon is essential for their performance. However, advanced neutron-optics geometries increasingly require fabrication routes that rely on graphite powders and organic binders rather than conventionally grown monolithic pyrolytic graphite. In this work, we investigate a binder-assisted approach in which graphite powder is combined with a phenol–formaldehyde resol resin (Plenco 14670), cured, and pyrolyzed to form a shaped carbon body. Because phenolic resins contain significant hydrogen-bearing functional groups, a central question is whether the thermal treatment is sufficient to remove hydrogen to levels compatible with neutron applications. We address this by combining inelastic neutron scattering (INS) and quantitative vibrational analysis to determine the hydrogen concentration before and after pyrolysis. The C–H stretching features near ∼ 380 meV serve as sensitive markers of residual hydrogen. Our results show that pyrolysis at 900◦C reduces the hydrogen concentration by a factor of approximately 54.4× relative to the diluted resin, demonstrating substantial decomposition of the binder-derived organic component. Nevertheless, comparison with a graphite reference reveals measurable residual hydrogen in the pyrolyzed composite, indicating incomplete removal at this temperature. These findings establish the feasibility of binder-assisted graphite shaping for neutron optics while highlighting the need for higher-temperature pyrolysis or extended dwell times to achieve the ultra-low hydrogen levels required for high-performance neutron-scattering instrumentation. Notice of Copyright This manuscript has been authored by UT-Battelle, LLC under Contract No. DEAC05-00OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes. The Department of Energy will provide public access to these results of federally sponsored research in accordance with the DOE Public Access Plan (http://energy.gov/downloads/doe-public-access-plan).
- Open Access
- 12 August 2025
- Published by Wiley in Interdisciplinary Materials
Linking Lattice Strain and Fractal Dimensions to Non‐monotonic Volume Changes in Irradiated Nuclear Graphite
Graphite's resilience to high temperatures and neutron damage makes it vital for nuclear reactors, yet irradiation alters its microstructure, degrading key properties. We used small‐ and wide‐angle X‐ray scattering to study neutron‐irradiated fine‐grain nuclear graphite (Grade G347A) across varied temperatures and fluences. Results show significant shifts in internal strain and porosity, correlating with radiation‐induced volume changes. Notably, porosity volume distribution (fractal dimensions) follows non‐monotonic volume changes, suggesting a link to the Weibull distribution of fracture stress.
- 12 August 2025
- Published by Wiley in Interdisciplinary Materials
Open AccessLinking Lattice Strain and Fractal Dimensions to Non‐monotonic Volume Changes in Irradiated Nuclear Graphite
Graphite's resilience to high temperatures and neutron damage makes it vital for nuclear reactors, yet irradiation alters its microstructure, degrading key properties. We used small‐ and wide‐angle X‐ray scattering to study neutron‐irradiated fine‐grain nuclear graphite (Grade G347A) across varied temperatures and fluences. Results show significant shifts in internal strain and porosity, correlating with radiation‐induced volume changes. Notably, porosity volume distribution (fractal dimensions) follows non‐monotonic volume changes, suggesting a link to the Weibull distribution of fracture stress.
- Open Access
- 1 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Degradation of Be2C at conditions expected in molten salt environments
- 1 July 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessDegradation of Be2C at conditions expected in molten salt environments
- Open Access
- 1 December 2024
- Published by Office of Scientific and Technical Information (OSTI)
Reference Materials for Laser and Xenon Flash Thermal Diffusivity Systems
This report presents the status of current standard reference materials for thermal diffusivity testing. In most thermal properties testing systems, it is common to use standard reference materials to show the reproducibility of the tests and certify the instrument is producing results within expected uncertainty range. The definition of reference materials or standards vary depending on the quality control protocols of the project. For thermal diffusivity, although there were standards available by the National Bureau of Standards (NBS) 40 years ago, there has been no recent NIST standard reference material (SRM). There are only a few sources that produce and provide traceable reference standards for thermal diffusivity. The certificate typically expires in 5 years and only applies to the specific lot of materials. Other reference materials are provided by the testing systems manufacturers. They are mostly well-known reference materials or materials used by the equipment manufacturers with historic data. However, most these reference materials no longer carry valid certificates. Various reference materials will be discussed along with the industry practice when only secondary standards are available.
- 1 December 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessReference Materials for Laser and Xenon Flash Thermal Diffusivity Systems
This report presents the status of current standard reference materials for thermal diffusivity testing. In most thermal properties testing systems, it is common to use standard reference materials to show the reproducibility of the tests and certify the instrument is producing results within expected uncertainty range. The definition of reference materials or standards vary depending on the quality control protocols of the project. For thermal diffusivity, although there were standards available by the National Bureau of Standards (NBS) 40 years ago, there has been no recent NIST standard reference material (SRM). There are only a few sources that produce and provide traceable reference standards for thermal diffusivity. The certificate typically expires in 5 years and only applies to the specific lot of materials. Other reference materials are provided by the testing systems manufacturers. They are mostly well-known reference materials or materials used by the equipment manufacturers with historic data. However, most these reference materials no longer carry valid certificates. Various reference materials will be discussed along with the industry practice when only secondary standards are available.
- Open Access
- 1 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Complete Degradation of Be2C at Conditions Expected in Molten Salt Environments
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessComplete Degradation of Be2C at Conditions Expected in Molten Salt Environments
The U.S. Department of Energy's Office of Scientific and Technical Information
- Open Access
- 1 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Status memorandum on ORNL support of vendor irradiation capsule design and ASME irradiation code development and new ASTM test standard development activities
The U.S. Department of Energy's Office of Scientific and Technical Information
- 1 September 2024
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessStatus memorandum on ORNL support of vendor irradiation capsule design and ASME irradiation code development and new ASTM test standard development activities
The U.S. Department of Energy's Office of Scientific and Technical Information