LMLuis Fernando Gamboa Martinez

Luis Fernando Gamboa Martinez

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Luis Fernando Gamboa Martinez has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evaluación de la resistencia teórica a la flexión de tres instrumentos utilizados en endodoncia mediante análisis de elementos finitos / Theoretical Evaluation through Finite Element Analysis of Flexural Strength of three Instruments used in Endodontics

    by Sandra Milena Prieto Cárdenas, Carlos Julio Cortés Rodríguez, Luis Fernando Gamboa Martínez, Javier Laureano Niño Barrera

    RESUMEN. Antecedentes: Los factores asociados a la fractura de un instrumento no se han examinado individualmente, este análisis es posible mediante el método de los elementos finitos Objetivo: Evaluar teóricamente el comportamiento a la flexión de tres diseños de instrumentos utilizados para la preparación biomecánica de los conductos radiculares mediante un análisis de elementos finitos. Métodos: Por medio de Ingeniería inversa se generaron los planos de las limas ProTaper Universal F2®, Mtwo 25/06® y WaveOne Primary® y con los planos posteriormente se construyeron los modelos matemáticos. Se realizó un análisis de elementos finitos y como material se determinó una aleación de Níquel-Titanio, con propiedades mecánicas certificadas por la base de datos MATWEB®. Se colocaron restricciones en todos los grados de libertad en el mango de cada uno de los modelos y se aplicó una carga de 1 Newton en la punta de cada instrumento. Resultados: Los esfuerzos de Von Mises resultantes fueron: Mtwo 25/06®: 673,363 MPa con una deformación del 18 %, ProTaper Universal F2®: 341,322 MPa con una deformación de 7.6 % y WaveOne Primary®: 227.593 MPa y una deformación de 5 %. Conclusión: Ninguna lima superó el límite de falla por fractura (960 MPa), sin embargo el modelo de la lima Mtwo 25/06® presentó los valores de esfuerzo y deformación más altos, lo cual indica una buena flexibilidad que le permite ser usada en conductos con curvas pronunciadas, pero debido a la deformación resultante se recomienda dar un solo uso para prevenir su fractura. ABSTRACT. Background: Factors associated with fracture of an instrument are not examined individually, this analysis is possible through the finite element method. Objective: To evaluate theoretically the flexural behavior of three designs of instruments used for biomechanical preparation of root canals using a finite element analysis. Methods: Through Reverse engineering drawings of ProTaper Universal files F2®, Mtwo 25 / 06® and WaveOne Primary® were generated and with these same planes mathematical models were built. Finite element analysis was performed and as material a nickel titanium alloy with mechanical properties certified by MATWEB® data base was determined. Restrictions in all degrees of freedom on the handle of each of the models were placed and a load of 1 Newton at the tip of each tool was applied. Results: The resulting Von Mises efforts were Mtwo 25 / 06®: 673.363 MPa with a strain of 18%, ProTaper Universal F2®: 341.322 MPa with a strain of 7.6% and WaveOne Primary®: 227 593 MPa and a strain of 5 %. Conclusion: No file exceeded the limit of failure by fracture (960 MPa), however the model Mtwo 25 / 06® lima presented stress values and higher deformation, indicating good flexibility allowing it to be used in ducts with sharp edges, but because of the resulting deformation is recommended that one use to prevent fracture

  • Open Access

    Análisis mediante CBCT de la configuración anatómica de los orificios de la raíz mesial del primer molar maxilar en población colombiana / CBCT Analysis of the Anatomical Configuration of First Maxillary Molar Mesial Root Holes in Colombian Population

    by Janneth Patricia Ortiz Meneses, Jorge Forero López, Luis Fernando Gamboa Martinez, Javier Laureano Niño Barrera

    RESUMEN. Antecedentes: Las tasas de fracaso en los tratamientos de endodoncia se presentan en un mayor porcentaje en el primer molar superior, debido a la no localización del conducto MV2 en la raíz MV. Los estudios sobre la morfología del primer molar superior no pueden ser extrapolados a otras poblaciones debido a las diferencias étnicas. Objetivo: de esta investigación fue determinar la incidencia de la configuración apical, la distancia media interorificio y la posible relación entre la distancia y la configuración apical, en la raíz MV del primer molar superior en población Colombiana. Métodos: Mediante un estudio “in vivo” se evaluaron un total de 113 imágenes CBCT de zona de molares superiores. El análisis consistió en la medición de la distancia entre los orificios de la raíz MV del primer molar superior, a nivel del piso de la cámara pulpar y determinar si hay una correlación con el tipo de configuración apical de la raíz MV. Resultados: El porcentaje de incidencia para las configuraciones apicales II y IV fueron 41,59 % y 58,40 %, respectivamente. La distancia media entre los orificios de entrada de la raíz MV del primer molar superior para configuraciones apicales II y IV (clasificación Vertucci) fueron 2,44 mm y 2,52 mm, respectivamente. Conclusiones: La configuración anatómica más común es la IV de Vertucci en 58,40 % de los casos. La distancia media interorificio en población colombiana fue de 2,49 mm. No se encontró una relación entre la distancia interorificio y el tipo de configuración apical. ABSTRACT. Background: Failure rates in endodontic treatments are presented in greater percentage in maxillary first molar, due to the non-localization of the second mesiobuccal canal in the mesiobuccal root. Several studies have developed in different populations, but the results cannot be extrapolated to other populations. Objective: The Objective of this research is to determine the incidence of the apical configuration, the interorificial average distance, and the possible relationship between the interorificial distance and the apical configuration, in the mesiobuccal root of first maxillary molar in Colombian population. Methods: Through a study “in vivo " A total of 113 CBCT images of superior molar zone were evaluated. The analysis consisted in measuring the interorificial distance at the floor level of the pulp chamber and determining the type of apical configuration of the MB root of maxillary first molar. This analysis was carried out using CS software for 3D images. A statistical analysis of the data was performed to determine the incidence of each apical configuration, the interorificial average distance, and in addition, the possible relationship between the interorificial distance and the apical configuration. Results: The percentage of incidence for apical configurations II and IV were 41.59 % and 58.40 %, respectively the interorificial average distance for apical configurations II and IV (Vertucci classification) were 2.44 mm and 2.52 mm, respectively. Conclusions: The interorificial average distance proved to be 2.49 mm. The most common anatomical configuration is IV for 58.40 % of the cases. There is no relationship between the interorificial distance and the apical configuration type.