John Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
John Wang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
A. A. Baker
Air Vehicles Division, Defence Science and Technology Organisation, Fishermans Bend, Australia
1 shared publicationD. Bitton
Advanced Composite Structures Australia Pty, Fishermans Bend, Australia
1 shared publication- Jayantha Kodikara
Department of Civil Engineering, Monash University, Clayton, Australia
1 shared publication - Leslie Wong
Department of Mechanical and Aerospace Engineering, Monash University, Wellington Rd, Clayton, VIC 3800, Australia
1 shared publication - Nabil Chowdhury
Department of Mechanical & Aerospace Engineering, Monash University, Wellington Road, Clayton, VIC 3168, Australia
1 shared publication Ross Dal Nevo
Crashlab Rd & Maritime Serv, Silverwater, Australia
1 shared publication
Latest Publications
- 1 January 2018
- Published by AHS International dba Vertical Flight Society in Journal of the American Helicopter Society
- Vol. 63 (1)
Assessment of Memory Cushions in Aircraft Seating for Injury Mitigation through Dynamic Impact Test
Dynamic impact tests with a FAA Hybrid III 50th percentile crash dummy in seats with and without a stroking energy-absorbing mechanism were conducted to assess the effectiveness of memory foam cushions in mitigating impact to the occupant during an aircraft crash. Polyurethane foam (PU) cushions were also tested for comparison. The results obtained when using a rigid seat indicated that for an 8.3-m/s impact, lumbar spinal injury would occur. Memory cushions could reduce lumbar force by up to 34%. For an impact speed of 6 m/s, a memory cushion could mitigate the impact to a tolerable level, while the injury would still occur with the PU cushions. The results with the energy-absorbing seats showed that for an 8.3-m/s impact speed, the seat with over 125 mm (5 inches) stroking length is able to prevent injury. Relatively softer memory cushions reduced lumbar force by over 15% compared with the PU cushions. With a stoke length of 75 mm (3 inches), bottom-out occurred and occupant lumbar spinal injury would occur. Relatively higher stiffness memory cushions reduced lumbar force by approximately 20%.
- 1 January 2018
- Published by AHS International dba Vertical Flight Society in Journal of the American Helicopter Society
- Vol. 63 (1)
Assessment of Memory Cushions in Aircraft Seating for Injury Mitigation through Dynamic Impact Test
Dynamic impact tests with a FAA Hybrid III 50th percentile crash dummy in seats with and without a stroking energy-absorbing mechanism were conducted to assess the effectiveness of memory foam cushions in mitigating impact to the occupant during an aircraft crash. Polyurethane foam (PU) cushions were also tested for comparison. The results obtained when using a rigid seat indicated that for an 8.3-m/s impact, lumbar spinal injury would occur. Memory cushions could reduce lumbar force by up to 34%. For an impact speed of 6 m/s, a memory cushion could mitigate the impact to a tolerable level, while the injury would still occur with the PU cushions. The results with the energy-absorbing seats showed that for an 8.3-m/s impact speed, the seat with over 125 mm (5 inches) stroking length is able to prevent injury. Relatively softer memory cushions reduced lumbar force by over 15% compared with the PU cushions. With a stoke length of 75 mm (3 inches), bottom-out occurred and occupant lumbar spinal injury would occur. Relatively higher stiffness memory cushions reduced lumbar force by approximately 20%.
- Open Access
Fatigue Damage Monitoring of a Composite Step Lap Joint Using Distributed Optical Fibre Sensors
Over the past few decades, there has been a considerable interest in the use of distributed optical fibre sensors (DOFS) for structural health monitoring of composite structures. In aerospace-related work, health monitoring of the adhesive joints of composites has become more significant, as they can suffer from cracking and delamination, which can have a significant impact on the integrity of the joint. In this paper, a swept-wavelength interferometry (SWI) based DOFS technique is used to monitor the fatigue in a flush step lap joint composite structure. The presented results will show the potential application of distributed optical fibre sensor for damage detection, as well as monitoring the fatigue crack growth along the bondline of a step lap joint composite structure. The results confirmed that a distributed optical fibre sensor is able to enhance the detection of localised damage in a structure.
Open AccessFatigue Damage Monitoring of a Composite Step Lap Joint Using Distributed Optical Fibre Sensors
Over the past few decades, there has been a considerable interest in the use of distributed optical fibre sensors (DOFS) for structural health monitoring of composite structures. In aerospace-related work, health monitoring of the adhesive joints of composites has become more significant, as they can suffer from cracking and delamination, which can have a significant impact on the integrity of the joint. In this paper, a swept-wavelength interferometry (SWI) based DOFS technique is used to monitor the fatigue in a flush step lap joint composite structure. The presented results will show the potential application of distributed optical fibre sensor for damage detection, as well as monitoring the fatigue crack growth along the bondline of a step lap joint composite structure. The results confirmed that a distributed optical fibre sensor is able to enhance the detection of localised damage in a structure.
- 1 May 2014
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 118 (1205) , 811-827
Riveted patch repairs for helicopter tail drive shafts with battle damage
The ability to repair battle damage in a helicopter tail drive shaft (TDS) caused by small arms fire is a very important capability. A successful repair will enable the helicopter to continue its mission or at least allow it to return safely to base. This paper describes assessment of conventional and novel repair techniques using riveted metallic patches to restore the balance and strength of a damaged TDS. Analytical approaches are provided for the design of the repair. Modal analyses indicated that the effect of repair on change of the natural frequency of the TDS was negligible. An experimental testing program was conducted to validate the proposed repair methods. It has been demonstrated that the proposed repair methods achieved sufficient balance restoration by a defined repair procedure, assuming the unbalance could not be measured during a repair in the field. The conventional thin, single aluminium sheet, riveted repair significantly restored static strength. However, it only gave a fatigue life of 15hrs, and thus the repaired shaft may only be used for limited time for a military mission. The improved thick, two-half aluminium shell, riveted repair had sufficient static strength and met the 100-hour fatigue requirement.
- 1 May 2014
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 118 (1205) , 811-827
Riveted patch repairs for helicopter tail drive shafts with battle damage
The ability to repair battle damage in a helicopter tail drive shaft (TDS) caused by small arms fire is a very important capability. A successful repair will enable the helicopter to continue its mission or at least allow it to return safely to base. This paper describes assessment of conventional and novel repair techniques using riveted metallic patches to restore the balance and strength of a damaged TDS. Analytical approaches are provided for the design of the repair. Modal analyses indicated that the effect of repair on change of the natural frequency of the TDS was negligible. An experimental testing program was conducted to validate the proposed repair methods. It has been demonstrated that the proposed repair methods achieved sufficient balance restoration by a defined repair procedure, assuming the unbalance could not be measured during a repair in the field. The conventional thin, single aluminium sheet, riveted repair significantly restored static strength. However, it only gave a fatigue life of 15hrs, and thus the repaired shaft may only be used for limited time for a military mission. The improved thick, two-half aluminium shell, riveted repair had sufficient static strength and met the 100-hour fatigue requirement.
- Open Access
- 1 January 2013
- Published by Hindawi Limited in Journal of Engineering
- Vol. 2013, 1-9
Prediction of Matrix Failure in Fibre Reinforced Polymer Composites
Recent development has enabled fibre and matrix failure in a fibre reinforced composite material to be predicted separately. Matrix yield/failure prediction is based on a Von Mises strain and first strain invariant criteria. Alternative matrix failure criteria for enhanced prediction accuracy are discussed in this paper. The proposed failure envelope formed with basic failure criteria intersects with uniaxial compression, pure shear and uniaxial tensile test data points smoothly. For failure of typical neat resin, significant improvement of prediction accuracy compared with measured material data is demonstrated. For a unit cell with a fibre and surrounding matrix with typical material properties, a FEM analysis indicates a significant improvement in prediction accuracy in the pure shear load case and a marginal improvement in the biaxial tensile load case. This paper also provided a preliminary discussion about the issues when material nonlinearity of the matrix material is involved.
- 1 January 2013
- Published by Hindawi Limited in Journal of Engineering
- Vol. 2013, 1-9
Open AccessPrediction of Matrix Failure in Fibre Reinforced Polymer Composites
Recent development has enabled fibre and matrix failure in a fibre reinforced composite material to be predicted separately. Matrix yield/failure prediction is based on a Von Mises strain and first strain invariant criteria. Alternative matrix failure criteria for enhanced prediction accuracy are discussed in this paper. The proposed failure envelope formed with basic failure criteria intersects with uniaxial compression, pure shear and uniaxial tensile test data points smoothly. For failure of typical neat resin, significant improvement of prediction accuracy compared with measured material data is demonstrated. For a unit cell with a fibre and surrounding matrix with typical material properties, a FEM analysis indicates a significant improvement in prediction accuracy in the pure shear load case and a marginal improvement in the biaxial tensile load case. This paper also provided a preliminary discussion about the issues when material nonlinearity of the matrix material is involved.