AZAlexey Zviagin

Alexey Zviagin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alexey Zviagin has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Humidity-independent highly selective H2S sensor based on ruthenium doped In2O3 synthesized using bio-template method

    by Alexey Shaposhnik, Alexey Vasiliev, Zhifu Liu, Nan Ma, Alexey Zviagin, Kirill Oreshkin, Olga Chuvenkova, Sofiia Titova, Kirill Fateev, Sergey Turishchev

  • Open Access

    Humidity-independent highly selective H2S sensor based on Ruthenium doped In2O3 synthesized using bio-template method

    by Alexey Shaposhnik, Alexey Vasiliev, Zhifu Liu, Nan Ma, Alexey Zviagin, Kirill Oreshkin, Olga Chuvenkova, Sofiia Titova, Kirill Fateev, Sergey Turishchev

    Highly selective hydrogen sulfide sensor based on 3 wt% Ruthenium doped In2O3 obtained by biotemplate synthesis was fabricated. For this, purified cellulose was impregnated with a solution containing Indium acetate In(CH3COO)3 and Ruthenium acetylacetonate Ru(C5H7O2)3, dried and calcinated at 600 оС. Nanomaterial obtained using this method consists of sintered 15 – 20 nm grains. The limit of Н2S detection of the sensor is much below 100 ppb. The sensor characteristics of the sensor were determined both at stationary temperature and at the pulse heating of the sensor from 100 to 450 оС with 15 s period. Sensor response to 10 ppm of Н2S at 150 оС is equal to 52, while the response in the pulsing heating regime exceeds the value of 185. The selectivity coefficient of the sensor with respect to carbon monoxide, hydrogen and ammonia gas at 150 оС is of about 100, this coefficient increases up to ~1000, when temperature modulation is used for sensor operation. The response of the sensor doesn’t decrease in humid atmosphere.

  • Open Access

    Humidity-independent highly selective H2S sensor based on Ruthenium doped In2O3 synthesized using bio-template method

    by Alexey Shaposhnik, Alexey Vasiliev, Zhifu Liu, Nan Ma, Alexey Zviagin, Kirill Oreshkin, Olga Chuvenkova, Sofiia Titova, Kirill Fateev, Sergey Turishchev

    Highly selective hydrogen sulfide sensor based on 3 wt% Ruthenium doped In2O3 obtained by biotemplate synthesis was fabricated. For this, purified cellulose was impregnated with a solution containing Indium acetate In(CH3COO)3 and Ruthenium acetylacetonate Ru(C5H7O2)3, dried and calcinated at 600 оС. Nanomaterial obtained using this method consists of sintered 15 – 20 nm grains. The limit of Н2S detection of the sensor is much below 100 ppb. The sensor characteristics of the sensor were determined both at stationary temperature and at the pulse heating of the sensor from 100 to 450 оС with 15 s period. Sensor response to 10 ppm of Н2S at 150 оС is equal to 52, while the response in the pulsing heating regime exceeds the value of 185. The selectivity coefficient of the sensor with respect to carbon monoxide, hydrogen and ammonia gas at 150 оС is of about 100, this coefficient increases up to ~1000, when temperature modulation is used for sensor operation. The response of the sensor doesn’t decrease in humid atmosphere.

  • Open Access

    Multivariate Calibration for Selective Analysis of Hydrogen Sulfide and Carbon Monoxide with Thermal Modulation of the SnO2–PdO Sensor

    by Alexey Shaposhnik, Pavel Moskalev, Alexey Vasiliev, Kirill Oreshkin, Alexey Zviagin, Elena Vysotskaya, Sergey Turishchev, Iuliia Kakuliia

    In this study, multivariate data processing during thermal modulation of the SnO2–PdO gas sensor was performed using the multivariate calibration (MC) method. We propose to supplement this method with a procedure that allows the solving of problems of both quantitative and qualitative analysis. The advantage of the extended method (Multivariate Calibration for Selective Analysis, MCSA) compared to other methods is its modest requirements for computing resources, which allows it to be easily implemented on standard microcontrollers. The MCSA method opens up the prospect of creating compact gas analyzers of a new generation, capable of selective gas analysis in hard-to-reach places in an autonomous mode. The implementation of the MCSA method was demonstrated using the example of selective determination of hydrogen sulfide and carbon monoxide by a sensor whose temperature periodically changed from 100 to 450 °C. The training sample data were transformed by the MCSA method, which allowed for successful qualitative and quantitative analysis of the test sample data.


  • Open Access

    Multivariate Calibration for Selective Analysis of Hydrogen Sulfide and Carbon Monoxide with Thermal Modulation of the SnO2–PdO Sensor

    by Alexey Shaposhnik, Pavel Moskalev, Alexey Vasiliev, Kirill Oreshkin, Alexey Zviagin, Elena Vysotskaya, Sergey Yu. Turishchev, Iuliia Kakuliia

    Multivariate data processing during thermal modulation of the SnO2–PdO gas sensor was performed using the multivariate calibration (MC) method. We propose to supplement this method with a procedure that allows solving problems of both quantitative and qualitative analysis. The advantage of the extended method (Multivariate Calibration for Selective Analysis, MCSA) compared to other methods is its modest requirements for computing resources, which allows it to be easily implemented on standard microcontrollers. The MCSA method opens up the prospect of creating compact gas analyzers of a new generation capable of selective gas analysis in hard-to-reach places in an autonomous mode. The implementation of the MCSA method was demonstrated using the example of selective determination of hydrogen sulfide and carbon monoxide by a sensor whose temperature periodically changed from 100 to 450 °C. The training sample data were transformed by the MCSA method, which allowed for successful qualitative and quantitative analysis of the test sample data.

  • Open Access

    Colorimetric assessment of the ozone-air mixture content during grain drying

    by Vladislav Yu. Kirmasov, Alexey A. Zviagin, Ivan V. Baskakov, Звягин Алексей Алексеевич

    BACKGROUND: The introduction of modern technical means and environmentally friendly technologies into agriculture is a relevant task for our country. The issues of plant protection, crop conservation and improving the quality of agricultural products through the introduction of innovative technologies are considered. One of the promising methods of influencing seeds is ozone treatment. This is due to the effectiveness of the impact of ozone as an oxidant on biochemical processes and metabolism. In this regard, it becomes relevant to conduct the research aimed at identifying the optimal concentration of the ozone-air mixture and evaluating the effectiveness of ozonation during drying of grain material. AIM: Creation of the test strips for determination of various concentrations of ozone-air mixture in the air. METHODS: During the study, methods of qualitative chemical interactions and mathematical processing of the results were used. The principle of the chemical method is to determine the ozone content indirectly by the amount of reagent that reacts with ozone. Thus, when potassium iodide interacts with ozone, iodine is restored. At the same time, its amount is proportional to the concentration of ozone in the gas mixture that was passed through the solution. RESULTS: The method to determine the concentration of an ozone-air mixture by colorimetric method is proposed. Test strips were created, and numerical values were assigned to each color in the software, which correspond to a certain concentration of the ozone-air mixture. CONCLUSION: The conducted study was helpful to create the method for determining the concentration of ozone in an ozone-air mixture by colorimetric method. The concentration dependence requires a linear ratio of the analytical signal to the exposure time. Five minutes is enough for this, while a twofold change in concentration corresponds to a twofold increase in response. The obtained test strips are helpful to determine the concentration of ozone necessary for effective drying of the seed material. However, the follow-up of this method and the large-scale testing will make it possible to extend the range of application and to increase its reliability.

  • Selective determination of hydrogen in a mixture with methane using a single metal oxide sensor

    by A.V. Shaposhnik, P.V. Moskalev, O.A. Arefieva, A.A. Zvyagin, O.V. Kul, A.A. Vasiliev


  • Open Access

    Synthesis and sensory properties of tungsten (VI) oxide-based nanomaterials

    by Alexey V. Shaposhnik, Alexey A. Zviagin, Stanislav V. Ryabtsev, Olga V. Dyakonova, Elena A. Vysotskaya

    The purpose of this work was to develop a methodology for the synthesis of WO3-based nano-scale materials, to provide their characterization, and to study their sensory properties. The nanopowder was made by slowly adding nitric acid to an aqueous solution of ammonium paratungstate,(NH4)10W21O41·xH2O, followed by centrifugation, drying, and calcination. The size of tungsten trioxide grains, which was 10-20 nm, was determined by transmission electron microscopy. According to X-ray phase analysis, the powder, which was calcined at a temperature of 500 °C, mainly consisted of a triclinic phase. Subsequently, diammine palladium (II) nitrate and terpeniol were added to the WO3 nanopowder to form a paste. The resulting paste was applied to a special dielectric substrate and calcined to a temperature of 750 °C. As a result, a fragile tungsten trioxide-based gel formed. The mass fraction of palladium in the fragile gel was 3%. The sensory properties of the obtained gas-sensitive material were studied under stationary (300 °C) and non-stationary temperature conditions (quick heating to 450 °C and slow cooling to 100 °C). A sharp increase in the sensitivity of a tungsten trioxide-based sensor was observed under non-stationary temperature conditions which depended on the composition of the gas-sensitive layer

  • Open Access

    Semiconductor metal oxide sensor for hydrogen sulphide operating under non-stationary temperature conditions

    by Alexey V. Shaposhnik, Alexey A. Zviagin, Olga V. Dyakonova, Stanislav V. Ryabtsev, Dina Ghareeb

    The aim of the work was to create a selective gas sensor for hydrogen sulphide. As a result of adding ammonia to the zinc acetate solution, centrifuging the obtained zinc hydroxide and subsequent calcination, a polydisperse zinc oxide powder with a grain size of 5–50 nm was obtained. The material was characterized using X-ray phase analysis and transmission electron microscopy. Subsequently, silver nitrate and terpeniol were added to the zinc oxide nanopowder to form a paste. The gas-sensitive material was obtained by applying the resulting paste on a special dielectric substrate and subsequent calcination, as a result of which the terpeniol burned out, and the silver nitrate turned into an oxide (the mass fraction of the silver was 3%). A non-stationary temperature mode for the operation of the sensor was selected, in which, after rapidheating of the sensor to 450 °C (2 seconds), slow (13 seconds) cooling to 100 °C occurred. Each subsequent heating-cooling cycle with a total period of 15 seconds began immediately after the end of the previous cycle. The use of an unsteady temperature mode in combination with the selection of the composition of the gas-sensitive layer made it possible to obtain a response of 200 for a hydrogen sulphide concentration of 1 ppm. Along with an increase in sensitivity, a significant increase in selectivity was also observed. The cross-sensitivity for the determination of hydrogen sulphide and other reducing gases (CO, NH3, H2) was more than three orders of magnitude. Thus, this sensor can be used to detect hydrogen sulphide even in the presence of interfering components. The use of highly selective sensors in the tasks of qualitative andquantitative analysis can significantly simplify the calibration in comparison with “electronic nose” devices. Devices based on highly selective sensors do not require the use of mathematical methods for processing multidimensional data arrays.

  • Open Access

    Selective Determination of Hydrogen Sulfide Using SnO2–Ag Sensor Working in Non-Stationary Temperature Regime

    by Alexey V. Shaposhnik, Pavel V. Moskalev, Alexey A. Zviagin, Margarita V. Duykova, Stanislav V. Ryabtsev, Dina A. A. Ghareeb, Alexey A. Vasiliev

    The application of a non-stationary regime of temperature modulation in metal oxide semiconductor sensor based on SnO2–Ag leads not only to a strongly increased sensor response, but also to a considerably improved sensor selectivity toward hydrogen sulfide. Selectivity with respect to other reducing gases (CO, NH3, H2) is about five orders of magnitude, enabling a correct selective determination of H2S in the presence of interfering gas components.