Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anna E. Frost has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Power flow in the air gap of linear electrical machines by utilisation of the Poynting vector: Part 2 ‐ simulations

    by Anna E. Frost, Jonathan Sjölund, Sandra Eriksson, Mats Leijon

    Different types of linear generators are simulated and their power flow in the air gap is investigated. The results are compared to the analytical expressions derived in Part 1. The simulations and the analytical expressions in Part 1 show the same general behaviour, but the magnitudes are lower for the analytical expressions. One explanation for the difference in magnitude can be that the harmonics of the electric and magnetic fields contribute to the power flow, which is not accounted for in the analytical expressions. Due to results from Part 1, it is investigated if changing the number of poles can decrease the tangential power flow while the normal power flow stays the same. As was suspected, changing the number of poles affected several other factors, which lead to an increase in the normal power flow when increasing the number of poles, even though the electrical power was the same. The tangential power flow also decreased for three out of four generators. Thereby, increasing the number of poles while keeping the same length of the machine, at the cost of reduced pole‐pitch, should be done with precaution.

  • Open Access

    Power flow in the air gap of linear electrical machines by utilization of the Poynting vector: Part 1 ‐ Analytical expressions

    by Anna E. Frost, Irina Temiz, Sandra Eriksson, Mats Leijon

    Analytical solutions and estimations for the power flow in the air gap of linear electrical machines of different geometries are derived from Poynting's theorem. The different geometries considered are flat one‐sided, multi‐sided, and tubular linear electrical machines. The radial power flow for all considered geometries is dependent on the area of the air gap, the electric field, the magnetic field, and the load angle. The tangential power flow for both flat one‐sided and tubular linear electrical machines is dependent of the area of the air gap, number of poles, the electric field, the magnetic field, and the load angle. The number of poles could be increased to decrease the tangential power flow in flat linear electrical machines. The expression for the tangential flow in tubular linear electrical machines is so complicated that it is difficult to draw conclusions from it.


  • Open Access

    End Effects and Geometric Compensation in Linear Permanent Magnet Synchronous Generators with Different Topologies

    by Jonathan Sjölund, Anna E. Frost, Mats Leijon, Sandra Eriksson

    Electricity production from ocean waves with different solutions is a topic of major research interest. Many of such designs are based on linear generators that inherently introduce end forces. In this paper, detent force using Maxwell Stress Tensor and induced voltage is initially investigated for two different winding patterns for a generator topology with buried magnets in a finite element software. Two ways of overcoming the end forces are further examined: the first method reduces the magnetic flux variations of the translator between stator and air. The second method aims at countering the end forces at both ends for full active stator area. A comparison is then made between buried and surface-mounted topologies for the second end effect compensation method. Both no-load and load conditions are investigated in the comparison. The end effect compensation shows promising results for both topologies. Some clear similarities of the extended stator used to counter the end forces are also apparent, where the stator extensions completely cover the outer poles of both topologies. The results also indicate a longer full active stator area for the buried topology for the same pole-pitch and stroke length, resulting in a higher average voltage for partial stator overlap.


  • Open Access

    An Overview of MnAl Permanent Magnets with a Study on Their Potential in Electrical Machines

    by Sofia Kontos, Anar Ibrayeva, Jennifer Leijon, Gustav Mörée, Anna E. Frost, Linus Schönström, Klas Gunnarsson, Peter Svedlindh, Mats Leijon, Sandra Eriksson

    In this paper, hard magnetic materials for future use in electrical machines are discussed. Commercialized permanent magnets used today are presented and new magnets are reviewed shortly. Specifically, the magnetic MnAl compound is investigated as a potential material for future generator designs. Experimental results of synthesized MnAl, carbon-doped MnAl and calculated values for MnAl are compared regarding their energy products. The results show that the experimental energy products are far from the theoretically calculated values with ideal conditions due to microstructure-related reasons. The performance of MnAl in a future permanent magnet (PM) generator is investigated with COMSOL, assuming ideal conditions. Simplifications, such as using an ideal hysteresis loop based on measured and calculated saturation magnetization values were done for the COMSOL simulation. The results are compared to those for a ferrite magnet and an NdFeB magnet. For an ideal MnAl hysteresis loop, it would be possible to replace ferrite with MnAl, with a reduced weight compared to ferrite. In conclusion, future work for simulations with assumptions and results closer to reality is suggested.


  • Open Access

    Partial Stator Overlap in a Linear Generator for Wave Power: An Experimental Study

    by Anna E. Frost, Liselotte Ulvgård, Linnea Sjökvist, Sandra Eriksson, Mats Leijon

    This paper presents a study on how the power absorption and damping in a linear generator for wave energy conversion are affected by partial overlap between stator and translator. The theoretical study shows that the electrical power as well as the damping coefficient change quadratically with partial stator overlap, if inductance, friction and iron losses are assumed independent of partial stator overlap or can be neglected. Results from onshore experiments on a linear generator for wave energy conversion cannot reject the quadratic relationship. Measurements were done on the inductance of the linear generator and no dependence on partial stator overlap could be found. Simulations of the wave energy converter’s operation in high waves show that entirely neglecting partial stator overlap will overestimate the energy yield and underestimate the peak forces in the line between the buoy and the generator. The difference between assuming a linear relationship instead of a quadratic relationship is visible but small in the energy yield in the simulation. Since the theoretical deduction suggests a quadratic relationship, this is advisable to use during modeling. However, a linear assumption could be seen as an acceptable simplification when modeling since other relationships can be computationally costly.