Rinat K. Islamgaliev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rinat K. Islamgaliev has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Marina A. Nikitina
Ufa University of Science and Technology, Ufa, Russia
4 shared publications - Vil D. Sitdikov
Ufa State Aviation Technical University
3 shared publications - Aleksandra A. Frik
Ufa University of Science and Technology, Ufa, Russia
2 shared publications - Artur V. Ganeev
Institute of Physics of Advanced Materials, Ufa University of Science and Technology, 32 Zaki Validi Str., 450076 Ufa, Russia
2 shared publications - Elvira Dinifovna Khafizova
Ufa University of Science and Technology, Ufa, Russia
2 shared publications - Hakan Yilmazer
Department of Metallurgical and Materials Engineering
2 shared publications
Latest Publications
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Structure and mechanical properties of Zn-1Cu-1Mn and Zn-0.8Al-0.5Ag alloys processed by ECAP
- 7 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-7
Structure and mechanical properties of Zn-1Cu-1Mn and Zn-0.8Al-0.5Ag alloys processed by ECAP
- Open Access
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 1,p. 81-91
Influence of crystallographic texture on the strength and electrical conductivity of ultrafine-grained copper
The paper covers the study of the influence of equal-channel angular pressing (ECAP) on the structure, crystallographic texture, mechanical properties and electrical conductivity of Cu-ETP copper (Russian analogue – M1), as well as the dependence of these characteristics on the orientation of the measurement direction relative to the cross-section (from −45 to 90°). The specific electrical conductivity and strength characteristics of the material in the as-delivered condition (hot-rolled) and the effect of annealing at a temperature of 450 °C of the original sample are investigated. Mechanical tests for uniaxial tension, a study of microhardness using the Vickers method and a study of specific electrical conductivity based on measuring the parameters of the vortex field excited in the surface layers of the body are carried out. It is found that ECAP processing leads to a significant increase in the ultimate tensile strength to 425 MPa compared to the initial state of 300 MPa. The maximum tensile strength of 425 MPa is achieved at orientation angles relative to the ECAP cross-section of −45°. A significant increase in microhardness to 1364–1405 MPa, tensile strength to 350–425 MPa and electrical conductivity to 101.4–102.4 % IACS is a consequence of the selected directions of cutting the samples relative to the ECAP axis. This indicates the dependence of both mechanical and electrical properties of ultrafine-grained samples on the crystallographic texture orientation. A Cu-ETP copper sample subjected to ECAP with a cutting angle deviating from the ECAP cross-section of the sample by 7.5° has the most optimal crystallographic orientation. In this case, the values of microhardness and electrical conductivity reached 1405 MPa and 102.4 % IACS, respectively.
- 1 January 2025
- Published by Togliatti State University in Frontier materials & technologies
- No. 1,p. 81-91
Open AccessInfluence of crystallographic texture on the strength and electrical conductivity of ultrafine-grained copper
The paper covers the study of the influence of equal-channel angular pressing (ECAP) on the structure, crystallographic texture, mechanical properties and electrical conductivity of Cu-ETP copper (Russian analogue – M1), as well as the dependence of these characteristics on the orientation of the measurement direction relative to the cross-section (from −45 to 90°). The specific electrical conductivity and strength characteristics of the material in the as-delivered condition (hot-rolled) and the effect of annealing at a temperature of 450 °C of the original sample are investigated. Mechanical tests for uniaxial tension, a study of microhardness using the Vickers method and a study of specific electrical conductivity based on measuring the parameters of the vortex field excited in the surface layers of the body are carried out. It is found that ECAP processing leads to a significant increase in the ultimate tensile strength to 425 MPa compared to the initial state of 300 MPa. The maximum tensile strength of 425 MPa is achieved at orientation angles relative to the ECAP cross-section of −45°. A significant increase in microhardness to 1364–1405 MPa, tensile strength to 350–425 MPa and electrical conductivity to 101.4–102.4 % IACS is a consequence of the selected directions of cutting the samples relative to the ECAP axis. This indicates the dependence of both mechanical and electrical properties of ultrafine-grained samples on the crystallographic texture orientation. A Cu-ETP copper sample subjected to ECAP with a cutting angle deviating from the ECAP cross-section of the sample by 7.5° has the most optimal crystallographic orientation. In this case, the values of microhardness and electrical conductivity reached 1405 MPa and 102.4 % IACS, respectively.
- 24 April 2024
- Published by Springer Nature in Russian Physics Journal
- Vol. 67 (5) , 550-557
Principles of Increasing the Strength and Toughness of Ferritic/Martensitic Steel Produced by Cold Rolling
- 24 April 2024
- Published by Springer Nature in Russian Physics Journal
- Vol. 67 (5) , 550-557
Principles of Increasing the Strength and Toughness of Ferritic/Martensitic Steel Produced by Cold Rolling
- Open Access
Effect of Plastic Deformation on the Structure and Mechanical Properties of the Zn-4Ag-1Cu Zinc Alloy
It is known that zinc biodegradable alloys are a promising material for producing biomedical implants for orthopedics and vascular stents. Among them, the Zn-Ag-Cu zinc alloy is of special interest due to the antibacterial and antimicrobial properties of Ag and Cu. To improve the mechanical properties of the Zn-4Ag-1Cu zinc alloy, the effect of equal-channel angular pressing (ECAP) on the microstructure and strength has been investigated. The ECAP conditions for the Zn-4Ag-1Cu alloy were chosen by modeling in the Deform 3 D program (temperature and strain rate). The microstructure was analyzed using transmission electron microscopy, scanning electron microscopy and X-ray diffraction analysis. The study of strength was carried out by measuring the microhardness and tensile tests of small samples with a gauge dimension of 0.8 × 1 × 4 mm3. The microstructure after ECAP was characterized by equiaxed grains ranging in a size from 1.5 µm to 4 µm with particles in a size from 200 nm to 1 µm uniformly distributed along the boundaries. The ECAP samples showed a high strength of 348 MPa and good ductility of up to 30%, demonstrating their great potential as promising materials for producing medical stents.
Open AccessEffect of Plastic Deformation on the Structure and Mechanical Properties of the Zn-4Ag-1Cu Zinc Alloy
It is known that zinc biodegradable alloys are a promising material for producing biomedical implants for orthopedics and vascular stents. Among them, the Zn-Ag-Cu zinc alloy is of special interest due to the antibacterial and antimicrobial properties of Ag and Cu. To improve the mechanical properties of the Zn-4Ag-1Cu zinc alloy, the effect of equal-channel angular pressing (ECAP) on the microstructure and strength has been investigated. The ECAP conditions for the Zn-4Ag-1Cu alloy were chosen by modeling in the Deform 3 D program (temperature and strain rate). The microstructure was analyzed using transmission electron microscopy, scanning electron microscopy and X-ray diffraction analysis. The study of strength was carried out by measuring the microhardness and tensile tests of small samples with a gauge dimension of 0.8 × 1 × 4 mm3. The microstructure after ECAP was characterized by equiaxed grains ranging in a size from 1.5 µm to 4 µm with particles in a size from 200 nm to 1 µm uniformly distributed along the boundaries. The ECAP samples showed a high strength of 348 MPa and good ductility of up to 30%, demonstrating their great potential as promising materials for producing medical stents.
- Open Access
Enhanced Fatigue Limit in Ultrafine-Grained Ferritic–Martensitic Steel
The influence of the ultrafine-grained (UFG) structure on the fatigue endurance limit and the nature of fatigue failure have been studied. It is shown that the formation of the UFG structure containing carbides and the coincidence site lattice relationship (CSL) and twin boundaries leads to an increase in the fatigue endurance limit. To study the mechanisms of fatigue failure, scanning and transmission electron microscopy and X-ray diffraction analysis were used. Studies have shown that the formation of the UFG structure as a result of rolling and subsequent heat treatment above the temperature of the ferrite/austenite phase transition leads to an increase in the fatigue endurance limit by more than 70%, from 475 to 800 MPa, compared to coarse-grained samples. The dynamic aging observed during fatigue tests was more pronounced in materials with a UFG microstructure. The influence of the CSL and twin boundaries on the nature of the fatigue failure of ferritic–martensitic steel is discussed.
Open AccessEnhanced Fatigue Limit in Ultrafine-Grained Ferritic–Martensitic Steel
The influence of the ultrafine-grained (UFG) structure on the fatigue endurance limit and the nature of fatigue failure have been studied. It is shown that the formation of the UFG structure containing carbides and the coincidence site lattice relationship (CSL) and twin boundaries leads to an increase in the fatigue endurance limit. To study the mechanisms of fatigue failure, scanning and transmission electron microscopy and X-ray diffraction analysis were used. Studies have shown that the formation of the UFG structure as a result of rolling and subsequent heat treatment above the temperature of the ferrite/austenite phase transition leads to an increase in the fatigue endurance limit by more than 70%, from 475 to 800 MPa, compared to coarse-grained samples. The dynamic aging observed during fatigue tests was more pronounced in materials with a UFG microstructure. The influence of the CSL and twin boundaries on the nature of the fatigue failure of ferritic–martensitic steel is discussed.
- Open Access
- 1 November 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 672 (1) , 012050
Strength and electrical conductivity of UFG Cu-Fe alloys subjected to HPT
This paper investigates the strength and specific conductivity of UFG Cu-Fe alloys processed by high-pressure torsion (HPT). The effect of an ultrafine-grained structure and further heat treatment on the increase of microhardness and specific conductivity is examined. The results of the structural study of the UFG samples by electron back-scatter diffraction (EBSD) are presented.
- 1 November 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 672 (1) , 012050
Open AccessStrength and electrical conductivity of UFG Cu-Fe alloys subjected to HPT
This paper investigates the strength and specific conductivity of UFG Cu-Fe alloys processed by high-pressure torsion (HPT). The effect of an ultrafine-grained structure and further heat treatment on the increase of microhardness and specific conductivity is examined. The results of the structural study of the UFG samples by electron back-scatter diffraction (EBSD) are presented.
- Open Access
Effects of the Tempering and High-Pressure Torsion Temperatures on Microstructure of Ferritic/Martensitic Steel Grade 91
Grade 91 (9Cr-1Mo) steel was subjected to various heat treatments and then to high-pressure torsion (HPT) at different temperatures. Its microstructure was studied using transmission electron microscopy (TEM) and X-ray diffraction (XRD). Effects of the tempering temperature and the HPT temperature on the microstructural features and microhardness in the ultrafine-grained (UFG) Grade 91 steel were researched. The study of the UFG structure formation takes into account two different microstructures observed: before HPT in both samples containing martensite and in fully ferritic samples.
Open AccessEffects of the Tempering and High-Pressure Torsion Temperatures on Microstructure of Ferritic/Martensitic Steel Grade 91
Grade 91 (9Cr-1Mo) steel was subjected to various heat treatments and then to high-pressure torsion (HPT) at different temperatures. Its microstructure was studied using transmission electron microscopy (TEM) and X-ray diffraction (XRD). Effects of the tempering temperature and the HPT temperature on the microstructural features and microhardness in the ultrafine-grained (UFG) Grade 91 steel were researched. The study of the UFG structure formation takes into account two different microstructures observed: before HPT in both samples containing martensite and in fully ferritic samples.
- Open Access
- 20 November 2017
- Published by MDPI AG in Preprints.org
Analysis of Precipitates in UFG Metallic Materials
In the present work, new possibilities of the X-ray diffraction for investigations of the phase composition, size, shape and volume fraction of particles in ultrafine-grained (UFG) martensitic steel and the Cu-Cr-Zr alloy have been demonstrated. For the first time, the method of X-ray diffraction in the transmission mode was used to identify particles with a volume fraction of less than one percent in the UFG materials studied. The small-angle X-ray scattering method was used to estimate the size and shape of dispersed particles. Specific features of the UFG structure determined by the X-ray diffraction are compared with the results of TEM studies.
- 20 November 2017
- Published by MDPI AG in Preprints.org
Open AccessAnalysis of Precipitates in UFG Metallic Materials
In the present work, new possibilities of the X-ray diffraction for investigations of the phase composition, size, shape and volume fraction of particles in ultrafine-grained (UFG) martensitic steel and the Cu-Cr-Zr alloy have been demonstrated. For the first time, the method of X-ray diffraction in the transmission mode was used to identify particles with a volume fraction of less than one percent in the UFG materials studied. The small-angle X-ray scattering method was used to estimate the size and shape of dispersed particles. Specific features of the UFG structure determined by the X-ray diffraction are compared with the results of TEM studies.
- Open Access
- 8 May 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 194 (1) , 012025
Effect of grain refinement on mechanical properties of martensitic steel
Microstructure and strength of commercial martensitic steel processed by equal channel angular pressing (ECAP) has been investigated using transmission electron microscopy and tensile tests. Application of ECAP led to significant grain refinement to a grain size of 0.8 µm and precipitation of particles with a size of 90 nm. Impact of annealing on thermal stability of ultrafine-grained structure was investigated. The contribution of various strengthening mechanisms to strength of steel was discussed.
- 8 May 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 194 (1) , 012025
Open AccessEffect of grain refinement on mechanical properties of martensitic steel
Microstructure and strength of commercial martensitic steel processed by equal channel angular pressing (ECAP) has been investigated using transmission electron microscopy and tensile tests. Application of ECAP led to significant grain refinement to a grain size of 0.8 µm and precipitation of particles with a size of 90 nm. Impact of annealing on thermal stability of ultrafine-grained structure was investigated. The contribution of various strengthening mechanisms to strength of steel was discussed.