SLShusen Li

Shusen Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Shusen Li has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Nonlinear analysis model of the progressive damage of aluminum–wood sandwich structures under high-speed impact conditions

    by Yan Zhang, Shusen Li

    The impact responses of various protective structures composed of 2A12 aluminum alloy and wood laminates were studied experimentally. The experiments were conducted using different impact energies. By varying the sandwich material thickness and using two different bullet shapes, the effects of the sandwich material’s damage process and the core layer thickness on the protective performance were studied. The multilayer structure’s core layer failure condition was determined using the improved 3D Hashin criterion and a finite element model was established using Abaqus software. Tensile and three-point bending tests were conducted and the progressive damage model was verified statically. The model was then verified dynamically using the Hopkinson bar test. The mechanical properties of the materials under high dynamic strain rates were obtained through action loading testing of the specimens at different loading rates. The loading waveform was analyzed and a stress-strain relationship diagram was drawn at various strain rates. By verifying the experimental data, a numerical model that could capture the deformation and failure details during crushing was established, and the composite target plate impact failure mode and the trajectory change law were described. This study could lead to use of a new impact damage prediction method for laminates.


  • Open Access

    Experiment on the impact response of aluminum alloy wood core sandwich composites

    by Shusen Li, Yan Zhang

    In this work, a protective structure with 2A12T4 aluminum alloy as the panel material and plywood as the core layer was designed. Penetration experiments were performed by firing multiple projectiles from a light gas gun. The impact behavior, damage mode, absorbed energy, and residual strength of the interlayer after impact were studied. The dynamic response and the failure of the interlayer were analyzed. Disbonding, fiber fracture, buckling, shear, and core fracture between the metal layer and the composite layer of the front panel were observed. The impact resistance of the sandwich plate was also studied. Based on the results of the experiments and numerical simulations, failure determination of the plywood core layer was achieved using the Hashin criterion, and a finite element model was established using ABAQUS software. High-speed impact testing was performed with a Hopkinson pressure bar. The stress–strain relationship under a high dynamic strain rate is given here, and the energy absorption efficiency under loading in different directions was analyzed. Finite element analysis of the representative volume elements in the wood microstructure was also carried out. The results reported here can be used to guide optimal design of sandwich structures suitable for use under high-speed impact conditions.


  • Open Access

    Experimental and numerical study on the dynamic response of aluminum alloy wood sandwich panels under high-velocity impact

    by Shusen Li, Yan Zhang

    The purpose of this study was to investigate the high-velocity impact response and failure modes of three-layer sandwich panels consisting of aluminum alloy sheets and plywood. The energy absorption mechanism and interaction between the plywood core and aluminum alloy panels were investigated by a high-velocity impact test. Different types of bullets were used in the impact test, and impact velocity parameters were obtained using a high-velocity camera to assess damage patterns. A full-scale finite element model was established to simulate the response mode of plywood sandwich under high-velocity impact. After the finite element model was verified by the experimental results, the energy absorption of the sandwich structure was further discussed. The results showed that the sandwich structure provided better protection than the double-layer structure. The analysis and predictions were in good agreement with the experimental results and numerical calculations. The experimental and numerical studies proposed in this paper are expected to provide new references and ideas for the design of multilayer structures with better impact resistance and lightweight characteristics.


  • Open Access

    Research on the influence of a micro-groove-orifice structure and its layout form on the static characteristics of aerostatic journal bearings under a high gas supply pressure

    by Wei Cui, Shusen Li, Bailin Zhu, Fei Yang, Bao Chen

    To solve the problems of a low gas supply pressure and low load capacity of traditional orifice-compensated aerostatic journal bearings (OCAJBs), this paper presents the design of a double-row gas supply micro-groove-orifice aerostatic journal bearing (MGOAJB). By establishing new governing equations and introducing the SST k- ω turbulence model, the influence of the micro-groove-orifice (MGO) structure and its layout form on the static characteristics of aerostatic journal bearings under a high gas supply pressure are studied. It is found that under high gas supply pressure, the MGO structure can significantly improve the load capacity and stiffness and reduce the gas consumption of the MGOAJB compared with the OCAJB. With additional MGO structures in the eccentric direction of the spindle, the load capacity and stiffness of the bearing increase substantially, and the gas flow also increases. The layout direction of the MGO has a prominent influence on the static characteristics of the MGOAJB. Axial MGOs have a higher load capacity and stiffness and lower gas flow. The accuracy of the simulation method is verified by experiments. This study provides a theoretical basis and method for the design of aerostatic journal bearings under a high gas supply pressure.


  • Open Access

    Research on the influence of supersonic phenomena on the gas film flow field of micron-groove-orifice aerostatic journal bearings under high gas supply pressure

    by Shusen Li, Wei Cui

    To solve the problem of performance degradation caused by supersonic phenomena under high gas supply pressures in orifice-compensated aerostatic journal bearings (OCAJBs), a double-row gas supply micron-groove-orifice aerostatic journal bearing (MGOAJB) is designed, and the SST k- ω turbulence model is used to analyze the influences of the supersonic phenomena on the gas film flow field under different gas supply pressures, gas film thicknesses and orifice diameters. Compared with traditional OCAJBs, under high gas supply pressure, supersonic phenomena occur near the gas film inlet in both the MGOAJB and the OCAJB. The Mach number, maximum pressure, temperature and Reynolds number of the OCAJB are higher than those of the MGOAJB, but the MGOAJB has a more stable gas film pressure due to pressure equalization. As the gas film thickness of the MGOAJB increases, the Mach number, Reynolds number and temperature near the gas film inlet increase, but the pressure decreases, the recovery of the pressure and temperature becomes more obvious when the gas velocity drops to a subsonic speed. With increases in the MGOAJB orifice diameter, the pressure, temperature and Reynolds number increase, the Mach number decreases, and the recovery of the pressure and gas temperature becomes more obvious.


  • Open Access

    Transient Analysis Method of an Axially Magnetized Novel Passive Eddy Current Damper for Suppressing Lateral Vibrations

    by Abdelrahman I. A. Eisa, Li Shusen, Zhang Yan, Wasim M. K. Helal

    A passive eddy current damper (PECD) can be adopted to provide a damping effect and drag force in rotating structure applications. The damping effect is formed as the result of induced eddy current, while the drag force is produced as the result of the repulsive force between the same axially poled magnets. However, modeling and approximating the damping effect, repulsive force, stiffness, the magnetic flux density (MFD) distribution, and eddy current prompted in PECD is a challenging task because of the complicated structure and operational conditions. This paper presents a new method for modeling and estimating the dynamic parameters of novel PECDs such as the damping effect, repulsive force, and stiffness for suppressing vibration in rotating structure applications. This self-powered, cost-effective PECD utilizes four arc-shaped and single ring-shaped permanent magnets with a cylindrical conductor placed between the arc magnets and the ring magnet to generate a damping effect and spring. Eddy currents are generated in the cylindrical conductor as the effect of the relative motion of the ring magnet concerning the arc magnets. An accurate and transient analysis method of the proposed system is carried out by using a three-dimensional finite-element method (3D-FEM). According to the procedures applied in the FE model solution, this new numerical method is appropriate and validated for analyzing PECDs and gaining good results by configuring the conductor and permanent magnets symmetrically. Finally, this novel 3D transient analysis method presents a perfect ability and accuracy for both modeling and calculating the PECD parameters.


  • Open Access

    Design and Experimentation of a Self-Sensing Actuator for Active Vibration Isolation System with Adjustable Anti-Resonance Frequency Controller

    by Yuan Fu, Shusen Li, Jiuqing Liu, Bo Zhao

    The vibration isolation system is now indispensable to high-precision instruments and equipment, which can provide a low vibration environment to ensure performance. However, the disturbance with variable frequency poses a challenge to the vibration isolation system, resulting in precision reduction of dynamic modeling. This paper presents a velocity self-sensing method and experimental verification of a vibration isolation system. A self-sensing actuator is designed to isolate the vibration with varying frequencies according to the dynamic vibration absorber structure. The mechanical structure of the actuator is illustrated, and the dynamic model is derived. Then a self-sensing method is proposed to adjust the anti-resonance frequency of the system without velocity sensors, which can also reduce the complexity of the system and prevent the disturbance transmitting along the cables. The self-sensing controller is constructed to track the variable frequency of the disturbance. A prototype of the isolation system equipped with velocity sensors is developed for the experiment. The experiment results show that the closed-loop transmissibility is less than −5 dB in the whole frequency rand and is less than −40 dB around, adding anti-resonance frequency which can be adjusted from 0 Hz to initial anti-resonance frequency. The disturbance amplitude of the payload can be suppressed to 10%.


  • The Modeling and Visual Control Simulation of Articulated Serpentine Manipulator

    by Haibo Xie, Shusen Li, Huayong Yang

    The serpentine manipulator is able to travel safely in a narrow space with its own high degree of flexibility, suitable for special working environments where traditional manipulator cannot enter. Focusing on the articulated serpentine manipulator, this paper establishes an accurate kinematics model according to the geometric structure and builds the simulation platform for visual motion controlling. The dynamic movement of the manipulator can be visualized through the three-dimensional graph. The simulation platform can also be used to quickly verify the correctness of different control algorithms for the articulated serpentine manipulator, greatly reducing the research cost and effectively shortening the development cycle.


  • Open Access

    Optimization of Factors Affecting Vibration Characteristics of Unbalance Response for Machine Motorized Spindle Using Response Surface Method

    by Elhaj A. I. Ahmed, Li Shusen

    In this study, the response surface (RS) method and forced rotordynamic analyses together with Finite‐Element‐Analysis (FEA) have been established to optimize the factors affecting the vibration characteristics. The spindle specification, bearings locations, cutting force, and motor‐rotor unbalance mass are proposed to represent the design factors and then they are utilized to develop Machine Motorized Spindle (MMS). The FEA‐based Design of Experiment (DOE) is adopted to simulate the output responses with the input factors, wherein these DOE design points are used to carry out the RS models to visualize more obvious factors affecting the dynamic characteristics of MMS. The sensitivities of these factors and their contributions to the vibration of imbalance response have been evaluated by using the RS models. The simulation results show that the motor‐rotor shaft inner diameter, the distance of the back bearing location, and the rotating unbalance‐mass are highly sensitive to the vibration characteristics compared to the other factors. It is found that more than two‐fifths of total vibration response amplitude has been conducted by induced rotating imbalance mass. The results also showed that the proposed factors optimization method is practicable and effective in improving the vibration response characteristics.


  • Open Access

    The vibration of machine motorized spindle based on forced rotordynamic analysis and response-surface method

    by Elhaj A. I. Ahmed, Li Shusen

    In this work, the dynamic of MMS exposing several excitation forces has been studied using forced Rotordynamic analysis. The Finite-Element-Model (FEM) based Design of Experiment (DOE); the sensitivities of factors on vibration response and their levels optimization have been carried out based on Response-Surface (RS) method. The results showed that the vibration response is considerably influenced by the rotating unbalance force. The vibration amplitude conducted by rotating unbalance force is more than two-by-five-time when compared to the other factors. In addition, the results obtained also showed that there are significant improvements in Structural Weight (SW) and vibration response. Thus, the factors level optimization technique, not only reduce in total material consumed but also the vibration response can be improved. The proposed vibration design approach is significant and successful in improving vibration of unbalance response.