DRDerek W. Ryter

Derek W. Ryter

*This is an algorithmically generated author record based on publicly available information.

Derek W. Ryter has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Simulation of the impacts of spring diversions on streamflow in the Strawberry Creek watershed, San Bernardino County, California, using an integrated hydrological model

    by Derek W. Ryter, Joseph A. Hevesi, Linda R. Woolfenden

    The Strawberry Creek watershed, in the San Bernardino Mountains of southern California, features a group of natural springs known as Arrowhead Springs that have been augmented with diversions in the form of sub-horizontal borings and tunnels. Understanding the effects of these structures on streamflow through groundwater capture is crucial for managing surface-water resources in this watershed. In this study, we constructed the Strawberry Creek integrated hydrological model to increase this understanding. The Strawberry Creek integrated hydrological model is an integrated surface runoff and groundwater model, GSFLOW to simulate surface runoff and infiltration and groundwater flow. The model has 263 rows and 176 columns in each of its three layers. The model area includes the Strawberry Creek and four adjacent watersheds. The precipitation-runoff modeling system was calibrated using two streamflow gaging stations, and the groundwater and surface-water flow model was calibrated to the reported spring diversion discharge and a sparse number of groundwater-level measurements. The Strawberry Creek integrated hydrological model was run with and without diversions active, and simulated streamflow was compared, indicating that in the headwaters of Strawberry Creek, about 35 percent of the diversion flow was captured from base flow.

  • Open Access

    Simulation of the Impacts of Spring Diversions on Streamflow in the Strawberry Creek Watershed, San Bernardino County, California, Using an Integrated Hydrological Model

    by Derek Ryter, Joseph Hevesi, Linda R Woolfenden

    The Strawberry Creek watershed, situated in the San Bernardino Mountains of southern California, features a group of natural springs known as Arrowhead Springs that have been augmented with diversions in the form of sub-horizontal borings and tunnels. Understanding the impact of these structures on streamflow through groundwater capture is crucial for managing surface-water resources in this watershed. In this study we constructed the Strawberry Creek integrated hydrological model (SCIHM) to increase this understanding. The SCIHM is an integrated surface runoff and groundwater model that uses the coupled groundwater and surface-water flow model (GSFLOW), which is based on the integration of the precipitation-runoff modeling system (PRMS) and the modular groundwater flow model commonly called MODFLOW, version MODFLOW-2005 software to simulate surface runoff and infiltration and groundwater flow. The model has three layers, 263 rows, and 176 columns. The model area includes the Strawberry Creek and four adjacent watersheds. The PRMS model was calibrated using two streamflow gaging stations and the GSFLOW model was calibrated to reported spring diversion discharge and a sparse number of groundwater-level measurements. The SCIHM was run with and without diversions active and simulated streamflow was compared, finding that in the headwaters of Strawberry Creek about 35 percent of the diversion flow was captured from base flow.

  • Open Access

    Updating and recalibrating the integrated Santa Rosa Plain Hydrologic Model to assess stream depletion and to simulate future climate and management scenarios in Santa Rosa, Sonoma County, California

    by Ayman H. Alzraiee, Andrew Rich, Linda R. Woolfenden, Derek W. Ryter, Enrique Triana, Richard G. Niswonger

    The Santa Rosa Plain Hydrologic Model (SRPHM) was developed and published in 2014 through a collaboration between the U.S. Geological Survey (USGS) and Sonoma Water to analyze the hydrologic system in the Santa Rosa Plain watershed, help meet the increasing demand for fresh water, and prepare for future uncertainties in water resources. The original model simulated hydrological conditions and water use from water years 1975 to 2010. Recently (2023), the USGS, in cooperation with Sonoma Water and the California State Water Resources Control Board, updated the SRPHM model to extend its simulation period to the end of the 2018 calendar year, incorporate new estimates of rural and agricultural water use, and use efficient input format for climate variables. The updated model was recalibrated, and evaluation of the new model calibration is included in this report. This report presents the results of comparing the hydraulic heads, streamflow, and groundwater budget simulated by the updated model with those generated by the original model and observed data. The main difference in the simulated budget between the original and updated SRPHM is the estimates of agricultural pumping, rural domestic pumping, and return flow generated from rural water use that was not simulated in the original model. The revised agricultural pumping is simulated using the agricultural package, which constrains pumping to available groundwater. The use of the agricultural package leads to a more realistic estimation of agricultural water use, with revised agricultural pumping being one-third less than that in the original model. The revised rural pumping is about half of the pumping in the original model because of using detailed parcel data to estimate population density in rural areas instead of coarse census tracts. Overall, average total inflows for water years 2006–10 simulated by the updated model were about 2 percent less than the original model, and the average total updated outflows were nearly 5 percent less than the original model. The updated model was then used to generate stream depletion maps, simulate climate change scenarios during 2019–99, and simulate water rights allocation using the Model for Decision Support in Integrated River Basin Management (MODSIM). The results from simulating eight future climate scenarios indicated either an increase in groundwater storage or no significant change in the next 80 years, along with an increase in recharge, an increase in actual evapotranspiration in six out of eight climate projections, and an increase in surface runoff. The increases in the simulated future groundwater storage, recharge, evapotranspiration, and runoff in most climate projections are mainly driven by the projected increase in precipitation in most of the future climate scenarios. The updated model also was used to test a pilot case study demonstrating water-resource allocation among different users with different water rights using the integrated MODSIM-Groundwater and Surface-Water Flow Model (GSFLOW) platform. The updated SRPHM serves as a valuable tool for analyzing historical and future hydrologic conditions in the Santa Rosa Plain watershed and preparing for future uncertainties.


  • Hydrogeology, numerical simulation of groundwater flow, and effects of future water use and drought for reach 1 of the Washita River alluvial aquifer, Roger Mills and Custer Counties, western Oklahoma, 1980–2015

    by John H. Ellis, Derek W. Ryter, Leland T. Fuhrig, Kyle W. Spears, Shana L. Mashburn, Ian M.J. Rogers

    First posted December 30, 2020 Director, Oklahoma-Texas Water Science Center U.S. Geological Survey 1505 Ferguson Lane Austin, Texas 78754–4501 The Washita River alluvial aquifer is a valley-fill and terrace alluvial aquifer along the valley of the Washita River in western Oklahoma that provides a productive source of groundwater for agricultural irrigation and water supply. The Oklahoma Water Resources Board (OWRB) has designated the westernmost section of the aquifer in Roger Mills and Custer Counties, Okla., as reach 1 of the Washita River alluvial aquifer; reach 1 is the focus of this report. The OWRB issued an order on November 13, 1990, that established the maximum annual yield (MAY; 120,320 acre-feet per year [acre-ft/yr]) and equal-proportionate-share (EPS) pumping rate (2.0 acre-feet per acre per year [(acre-ft/acre)/yr]) for reach 1 of the Washita River alluvial aquifer. The MAY and EPS were based on hydrologic investigations that evaluated the effects of potential groundwater withdrawals on groundwater availability in the Washita River alluvial aquifer. Every 20 years, the OWRB is statutorily required to update the hydrologic investigation on which the MAY and EPS were based. Because 30 years have elapsed since the last order was issued, the U.S. Geological Survey, in cooperation with the OWRB, conducted a new hydrologic investigation and evaluated the effects of potential groundwater withdrawals on groundwater flow and availability in the Washita River alluvial aquifer. The Washita River is the primary source of inflow to Foss Reservoir, a Bureau of Reclamation reservoir constructed in 1961 for flood control, water supply, and recreation. Foss Reservoir provides water for Bessie, Clinton, New Cordell, and Hobart, Okla. Nearly 98 percent of the total groundwater use from the Washita River alluvial aquifer during 1967 to 2015 was for irrigation; other uses of groundwater in the study area include public supply, mining, and agriculture. A hydrogeologic framework was developed for the Washita River alluvial aquifer and included the physical characteristics of the aquifer, the geologic setting, the hydraulic properties of hydrogeologic units, the potentiometric surface (water table), and groundwater-flow directions at a scale that captures the regional controls on groundwater flow. The Washita River alluvial aquifer consists of alluvium and terrace deposits that were transported primarily by water and range from clay to gravel in size. The terrace includes windblown deposits of silt size and, in some cases, contains gravel laid down at several levels along former courses of present-day rivers. A conceptual flow model is a simplified description of the aquifer system that includes hydrologic boundaries, major inflow and outflow sources of the groundwater-flow system, and a conceptual water budget with the estimated mean flows between those hydrologic boundaries. During the study period 1980–2015, mean annual groundwater withdrawals, predominantly used for agricultural irrigation, totaled 5,502 acre-ft/yr, or 14 percent of aquifer outflows. When applied across the 132-square-mile aquifer area used for modeling purposes (84,366 acres), mean annual recharge of 3.15 inches per year corresponds to a mean annual recharge volume of 22,169 acre-ft/yr, or 56 percent of aquifer inflows. The annual saturated-zone evapotranspiration outflow was 11,828 acre-ft/yr for the Washita River alluvial aquifer, or about 30 percent of aquifer outflows. For the Washita River alluvial aquifer, lateral flow was 17,157 acre-ft/yr, or 44 percent of the aquifer inflows. The conceptual flow model and hydrogeologic framework were used to conceptualize, design, and build the numerical groundwater-flow model. A numerical groundwater-flow model of the Washita River alluvial aquifer was constructed by using MODFLOW-2005. The Washita River alluvial aquifer groundwater-model grid was spatially discretized into 350-foot (ft) cells and two layers. Layer 1 represented the undifferentiated alluvium and terrace deposits of Quaternary age, and layer 2 represented the bedrock of Permian age, which was given a uniform nominal thickness of 100 ft. The groundwater-simulation period was temporally discretized into 433 monthly transient stress periods, representing January 1980 to December 2015. An initial 365-day steady-state stress period was configured to represent mean annual inflows and outflows from the Washita River alluvial aquifer for the study period. The groundwater-flow model was calibrated manually and by automated adjustment of model inputs by using PEST++. Calibration targets for the Washita River alluvial aquifer model included groundwater-level observations and reservoir-stage observations, as well as base-flow and stream-seepage estimates. Three groundwater-availability scenarios were used in the calibrated groundwater model to (1) estimate the EPS pumping rate that retains the saturated thickness that meets the minimum 20-year life of the aquifer, (2) quantify the effects of projected pumping rates on groundwater storage over a 50-year period, and (3) evaluate how projected pumping rates extended 50 years into the future and sustained hypothetical drought conditions over a 10-year period affect base flow and groundwater in storage. The results of the groundwater-availability scenarios could be used by the OWRB to reevaluate the established MAY of groundwater from the Washita River alluvial aquifer. EPS scenarios for the Washita River alluvial aquifer were run for periods of 20, 40, and 50 years. The 20-, 40-, and 50-year EPS pumping rates under normal recharge conditions were 1.7, 1.6, and 1.6 (acre-ft/acre)/yr, respectively. Given the aquifer area used for modeling purposes (84,366 acres), these rates correspond to annual yields of 142,579, 134,986, and 134,986 acre-ft/yr, respectively. Groundwater storage at the end of the 20-year EPS scenario was about 281,000 acre-feet (acre-ft), or about...


  • Summary of U.S. Geological Survey studies conducted in cooperation with the Citizen Potawatomi Nation, central Oklahoma, 2011–14

    by William J. Andrews, Carol J. Becker, Derek W. Ryter, S. Jerrod Smith

    The U.S. Geological Survey conducted hydrologic studies and published three U.S. Geological Survey scientific investigations reports in cooperation with the Citizen Potawatomi Nation from 2011 to 2014 to characterize the quality and quantity of water resources. The study areas of those reports consisted of approximately 960 square miles in parts of three counties in central Oklahoma. This study area has multiple abundant sources of water, being underlain by three principal aquifers (alluvial/terrace, Central Oklahoma, and Vamoosa-Ada), being bordered by two major rivers (North Canadian and Canadian), and having several smaller drainages including the Little River in the central part of the study area and Salt Creek in the southeastern part of the study area. The Central Oklahoma aquifer (also referred to as the “Garber-Wellington aquifer”) underlies approximately 3,000 square miles in central Oklahoma in parts of Cleveland, Logan, Lincoln, Oklahoma, and Pottawatomie Counties and much of the study area. Water from these aquifers is used for municipal, industrial, commercial, agricultural, and domestic supplies. Much of the water in the study area is of good quality; however, in some parts of this area water quality was impaired by very hard surface water and groundwater, large chloride concentrations in some smaller streams, relatively large concentrations of nitrogen and phosphorus nutrients and large counts of fecal-indicator bacteria in the North Canadian River, and uranium concentrations that exceeded the U.S. Environmental Protection Agency Maximum Contaminant Level of 30 micrograms per liter for public water supplies in water samples collected from a small number of wells. Most stream-water samples collected from the Little River by the U.S. Geological Survey in 2012–13 had dissolved solids concentrations exceeding the U.S. Environmental Protection Agency Secondary Maximum Contaminant Level for public water supplies of 500 milligrams per liter. Larger numbers of organic compounds were measured in water samples collected from the North Canadian River than the Little River. Numerical groundwater-flow models were created to characterize flow systems in aquifers underlying this study area and areas of particular interest within the study area. Those models were used to estimate sustainable groundwater yields from parts of the North Canadian River alluvial aquifer, characterize groundwater/surface-water interactions, and estimate the effects of a 10-year simulated drought on streamflows and water levels in alluvial and bedrock aquifers. Pumping of wells at the Iron Horse Industrial Park was estimated to cause negligible infiltration of water from the adjoining North Canadian River. A 10-year simulated drought of 50 percent of normal recharge was tested for the period 1990–2000. For this period, the total amount of groundwater in storage was estimated to decrease by 8.6 percent in the North Canadian River alluvial aquifer and approximately 0.2 percent in the Central Oklahoma aquifer, and groundwater flow to streams was estimated to decrease by 28–37 percent. This volume of groundwater loss showed that the Central Oklahoma aquifer is a bedrock aquifer that has relatively low rates of recharge from the land surface. The simulated drought decreased simulated streamflow, composed of base flow, in the North Canadian River at Shawnee, Okla., which did not recover to predrought conditions until the relatively wet year of 2007 after the simulated drought period.

  • Hydrogeological framework, numerical simulation of groundwater flow, and effects of projected water use and drought for the Beaver-North Canadian River alluvial aquifer, northwestern Oklahoma

    by Derek W. Ryter, Jessica S. Correll

    This report describes a study of the hydrology, hydrogeological framework, numerical groundwater-flow models, and results of simulations of the effects of water use and drought for the Beaver-North Canadian River alluvial aquifer, northwestern Oklahoma. The purpose of the study was to provide analyses, including estimating equal-proportionate-share (EPS) groundwater-pumping rates and the effects of projected water use and droughts, pertinent to water management of the Beaver-North Canadian River alluvial aquifer for the Oklahoma Water Resources Board. The Beaver-North Canadian River alluvial aquifer consists of unconsolidated sand, gravel, silt, and clay in varying proportions that underlies the Beaver and North Canadian River Valleys for approximately 175 miles (mi) from the Oklahoma Panhandle to the western edge of Oklahoma City in central Oklahoma. The aquifer as delineated for this study varies from 4 to 12 mi wide and is as thick as 308 feet (ft) in the northwest where the aquifer includes the Ogallala Formation. There are two distinct but in most areas hydraulically connected alluvial units that compose the Beaver-North Canadian River alluvial aquifer: a Quaternary-age topographically higher terrace deposit and a topographically lower, younger alluvium along the active river channel that includes active and Quaternary-age alluvium. The Beaver River composes the headwaters of the North Canadian River, which begins at the confluence of the Beaver River and Wolf Creek. The aquifer is divided for water management into two geographic areas: Reach I upstream from Canton Dam and Reach II downstream from Canton Dam. Reach I covers an area of approximately 874 square miles (mi2), and Reach II covers an area of approximately 371 mi2. The Beaver-North Canadian River alluvial aquifer crosses several climatic zones, from semiarid in the west to continental subhumid in the east. Mean annual precipitation varies from 23.5 inches (in.) in the western part of this aquifer to 35.7 in. in the east. Surface-water demands were met through numerous temporary and permanent surface-water diversions from the Beaver and North Canadian Rivers during the period of study. During the study period, seven diversions removed a mean annual 2,000 acre-feet (acre-ft) of water from Reach I. There were 14 diversions from Reach II with a mean annual permitted volume of approximately 81,000 acre-ft, including diversion into the Lake Hefner Canal for the Oklahoma City public water supply. During the period of this study, 17 temporary surface-water diversion permits were active in Reach I, with total permitted volumes of 2,000 acre-ft, and 41 diversions were active in Reach II, with total permitted volumes of 38,000 acre-ft. The total water use for each temporary permit was assumed to be taken over the 3-month period allotted to temporary withdrawal permits. The groundwater-use analysis full period of record, 1967–2011, was divided into two sub-intervals because of varying water use, 1970–80 and 1981–2011. Groundwater use in Reach I and Reach II was substantially greater from 1970 to 1980 compared to the rest of the period, and the sub-period 1981–2011 was used because this period includes recent population growth and modern irrigation methods. The total mean annual groundwater use in Reach I was 15,309 acre-feet per year (acre-ft/yr) during 1967–2011; 20,724 acre-ft/yr during 1970–80, and 13,739 acre-ft/yr during 1981–2011. Total mean annual groundwater use in Reach II was similar but slightly less than in Reach I, with 14,098 acre-ft/yr during 1967–2011; 19,963 acre-ft/yr during 1970–80; and 12,285 acre-ft/yr during 1981–2011. Irrigation composed 72 percent of groundwater use in Reach I and 48 percent of groundwater use in Reach II during the 1967–2011 period. Public water supply was a much smaller proportion of total groundwater use in Reach I (15 percent) than in Reach II (39 percent). The proportion of groundwater use for power was 10 percent in Reach I and 5.2 percent in Reach II. All other water-use categories in Reach I only composed 2.2 percent of groundwater use in Reach I. In Reach II, industrial, mining, and commercial categories combined accounted for 4.4 percent of groundwater use; recreation, fish, and wildlife groundwater use accounted for 2.3 percent; and nonirrigated agriculture accounted for 1.5 percent of groundwater use. Permian-age bedrock underlies the Beaver-North Canadian River alluvial aquifer. In the east, the Dog Creek Shale, the Duncan Sandstone, and the Blaine and Chickasha Formations, none of which are notable sources of groundwater in the study area, underlie the Beaver-North Canadian River alluvial aquifer. In the northwestern part of Reach I, bedrock is composed of the Rush Springs and Marlow Formations, which are productive aquifers in some areas. The Cloud Chief Formation is not a source of groundwater. One hydrogeological unit was delineated in the Beaver-North Canadian River alluvial aquifer, composed of the terrace deposits and alluvium, with limited flow between this unit and bedrock units. Groundwater in this aquifer generally flows from northwest to southeast and across the aquifer toward the Beaver and North Canadian Rivers. Groundwater recharge from precipitation was estimated for the entire Beaver-North Canadian River alluvial aquifer and then itemized for both reaches by using a soil-water-balance (SWB) model. At two locations in Reach I, a water-table fluctuation method was used to estimate local recharge. Total mean annual groundwater recharge from the soil-water-balance method was estimated to be approximately 136,400 acre-ft in Reach I and 82,400 acre-ft in Reach II; the mean annual recharge for both reaches combined was approximately 218,800 acre-ft. Two sites in Reach I located at observation wells with continuous water-level measurements and nearby streamflow-gaging stations with precipitation gages...


  • Open Access

    Simulation of groundwater flow and analysis of the effects of water-management options in the North Platte Natural Resources District, Nebraska

    by Steven M. Peterson, Amanda T. Flynn, Joseph Vrabel, Derek W. Ryter

    The North Platte Natural Resources District (NPNRD) has been actively collecting data and studying groundwater resources because of concerns about the future availability of the highly inter-connected surface-water and groundwater resources. This report, prepared by the U.S. Geological Survey in cooperation with the North Platte Natural Resources District, describes a groundwater-flow model of the North Platte River valley from Bridgeport, Nebraska, extending west to 6 miles into Wyoming. The model was built to improve the understanding of the interaction of surface-water and groundwater resources, and as an optimization tool, the model is able to analyze the effects of water-management options on the simulated stream base flow of the North Platte River. The groundwater system and related sources and sinks of water were simulated using a newton formulation of the U.S. Geological Survey modular three-dimensional groundwater model, referred to as MODFLOW–NWT, which provided an improved ability to solve nonlinear unconfined aquifer simulations with wetting and drying of cells. Using previously published aquifer-base-altitude contours in conjunction with newer test-hole and geophysical data, a new base-of-aquifer altitude map was generated because of the strong effect of the aquifer-base topography on groundwater-flow direction and magnitude. The largest inflow to groundwater is recharge originating from water leaking from canals, which is much larger than recharge originating from infiltration of precipitation. The largest component of groundwater discharge from the study area is to the North Platte River and its tributaries, with smaller amounts of discharge to evapotranspiration and groundwater withdrawals for irrigation. Recharge from infiltration of precipitation was estimated with a daily soil-water-balance model. Annual recharge from canal seepage was estimated using available records from the Bureau of Reclamation and then modified with canal-seepage potentials estimated using geophysical data. Groundwater withdrawals were estimated using land-cover data, precipitation data, and published crop water-use data. For fields irrigated with surface water and groundwater, surface-water deliveries were subtracted from the estimated net irrigation requirement, and groundwater withdrawal was assumed to be equal to any demand unmet by surface water. The groundwater-flow model was calibrated to measured groundwater levels and stream base flows estimated using the base-flow index method. The model was calibrated through automated adjustments using statistical techniques through parameter estimation using the parameter estimation suite of software (PEST). PEST was used to adjust 273 parameters, grouped as hydraulic conductivity of the aquifer, spatial multipliers to recharge, temporal multipliers to recharge, and two specific recharge parameters. Base flow of the North Platte River at Bridgeport, Nebraska, streamgage near the eastern, downstream end of the model was one of the primary calibration targets. Simulated base flow reasonably matched estimated base flow for this streamgage during 1950–2008, with an average difference of 15 percent. Overall, 1950–2008 simulated base flow followed the trend of the estimated base flow reasonably well, in cases with generally increasing or decreasing base flow from the start of the simulation to the end. Simulated base flow also matched estimated base flow reasonably well for most of the North Platte River tributaries with estimated base flow. Average simulated groundwater budgets during 1989–2008 were nearly three times larger for irrigation seasons than for non-irrigation seasons. The calibrated groundwater-flow model was used with the Groundwater-Management Process for the 2005 version of the U.S. Geological Survey modular three-dimensional groundwater model, MODFLOW–2005, to provide a tool for the NPNRD to better understand how water-management decisions could affect stream base flows of the North Platte River at Bridgeport, Nebr., streamgage in a future period from 2008 to 2019 under varying climatic conditions. The simulation-optimization model was constructed to analyze the maximum increase in simulated stream base flow that could be obtained with the minimum amount of reductions in groundwater withdrawals for irrigation. A second analysis extended the first to analyze the simulated base-flow benefit of groundwater withdrawals along with application of intentional recharge, that is, water from canals being released into rangeland areas with sandy soils. With optimized groundwater withdrawals and intentional recharge, the maximum simulated stream base flow was 15–23 cubic feet per second (ft3/s) greater than with no management at all, or 10–15 ft3/s larger than with managed groundwater withdrawals only. These results indicate not only the amount that simulated stream base flow can be increased by these management options, but also the locations where the management options provide the most or least benefit to the simulated stream base flow. For the analyses in this report, simulated base flow was best optimized by reductions in groundwater withdrawals north of the North Platte River and in the western half of the area. Intentional recharge sites selected by the optimization had a complex distribution but were more likely to be closer to the North Platte River or its tributaries. Future users of the simulation-optimization model will be able to modify the input files as to type, location, and timing of constraints, decision variables of groundwater withdrawals by zone, and other variables to explore other feasible management scenarios that may yield different increases in simulated future base flow of the North Platte River.