Marvin Scherzinger
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marvin Scherzinger has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
- Martin Kaltschmitt
Institute of Environmental Technology and Energy Economics, Hamburg University of Technology (TUHH), Hamburg, Germany
15 shared publications Martin Kaltschmitt
9 shared publications- Johannes Gescher
Hamburg University of Technology
4 shared publications - Jana Schultz
Hamburg University of Technology (TUHH), Institute of Environmental Technology and Energy Economics (IUE), Eissendorfer Strasse 40, 21073 Hamburg, Germany
3 shared publications - Stanislav Parsin
Institute of Environmental Technology and Energy Economics, Hamburg University of Technology, Eissendorfer Str. 40, 21073 Hamburg, Germany
3 shared publications - Theresa Siegmund
Technische Universität Hamburg (TUHH)
3 shared publications
Latest Publications
- 12 August 2026
- Published by Elsevier in Renewable Energy
- Vol. 275
Assessment of fuel property enhancement toward TRL advancement in biomass torrefaction
- 12 August 2026
- Published by Elsevier in Renewable Energy
- Vol. 275
Assessment of fuel property enhancement toward TRL advancement in biomass torrefaction
- Open Access
- 7 August 2026
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 28 (8) , 216
From solar radiation to green methanol: an energy efficiency of electricity- and biomass-based provision pathways
- 7 August 2026
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 28 (8) , 216
Open AccessFrom solar radiation to green methanol: an energy efficiency of electricity- and biomass-based provision pathways
- Open Access
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Sulfuric acid hydrolysis of isolated xylan: A statistical optimization approach
Sulfuric acid hydrolysis conditions for carbohydrates often represent a compromise resulting in suboptimal outcomes. Therefore, the sulfuric acid hydrolysis of xylan isolated from wheat straw hemicellulose was systematically investigated and optimized. The wheat straw xylan was obtained via saturated steam autohydrolysis followed by ethanol precipitation. This xylan was compared with standards derived from beech wood and corn cobs. A statistical experimental design was employed to elucidate the relationships between input (reaction temperature, reaction time and sulfuric acid weight fraction) and output parameters (xylose and furfural yields). Generally, reaction temperatures below 110 °C are preferred for hydrolysis of isolated xylan. For high xylose yields, a sulfuric acid weight fraction of 6 wt% is effective. A multi-objective optimization can be applied to simultaneously minimize furfural formation. Precipitated xylans require more severe hydrolysis conditions compared to the hydrolysates prior to precipitation due to lacking of biomass matrix including organic acids. With a simple hemicellulose-first process, wheat straw xylan of relatively high purity and without analytical matrix effects can be obtained. Within the investigation scope, the regression models provide a robust basis for optimizing acid hydrolysis parameters and highlight their critical role in carbohydrate analysis. Future work should investigate the transferability of the methodology.
- 14 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSulfuric acid hydrolysis of isolated xylan: A statistical optimization approach
Sulfuric acid hydrolysis conditions for carbohydrates often represent a compromise resulting in suboptimal outcomes. Therefore, the sulfuric acid hydrolysis of xylan isolated from wheat straw hemicellulose was systematically investigated and optimized. The wheat straw xylan was obtained via saturated steam autohydrolysis followed by ethanol precipitation. This xylan was compared with standards derived from beech wood and corn cobs. A statistical experimental design was employed to elucidate the relationships between input (reaction temperature, reaction time and sulfuric acid weight fraction) and output parameters (xylose and furfural yields). Generally, reaction temperatures below 110 °C are preferred for hydrolysis of isolated xylan. For high xylose yields, a sulfuric acid weight fraction of 6 wt% is effective. A multi-objective optimization can be applied to simultaneously minimize furfural formation. Precipitated xylans require more severe hydrolysis conditions compared to the hydrolysates prior to precipitation due to lacking of biomass matrix including organic acids. With a simple hemicellulose-first process, wheat straw xylan of relatively high purity and without analytical matrix effects can be obtained. Within the investigation scope, the regression models provide a robust basis for optimizing acid hydrolysis parameters and highlight their critical role in carbohydrate analysis. Future work should investigate the transferability of the methodology.
- Open Access
- 27 April 2026
- Published by CarbonPlan
Carbon dioxide removal efficiency of co-applied and co-pyrolyzed feedstocks for enhanced rock weathering and biochar in a sandy soil
Enhanced rock weathering (ERW) and pyrogenic carbon capture and storage (PyCCS) are promising land based approaches for carbon dioxide removal (CDR), yet their co-deployment remains poorly understood. This study investigates how co-application of minerals with biochar and co-pyrolysing biomass with minerals influence mineral weathering, alkalinity production, and carbon sequestration in a sandy soil with low cation exchange capacity (CEC) and low organic carbon (Corg) content. We compared concrete, steel slag, basanite, serpentinised peridotite, limestone and biochar as pure and co-applications, and rock enhanced biochars (RE-biochars) from dry-mixing and wet-impregnation of biomass and consecutive co-pyrolysis. Downflow columns filled with amended sandy soil were incubated for 75 weeks under elevated pCO2 while monitoring cation fluxes, trace metal release, dissolved organic carbon (DOC) dynamics, and changes in soil CEC. Wet impregnation substantially altered RE-biochar properties by increasing the pyrolysis carbon yield and fraction of highly stable pyrogenic carbon particularly for Mg rich feedstocks. Reduced DOC losses and enhanced alkalinity production, attributed to mineral weathering as the geogenic inorganic carbon sink (IC-Sink), was present for co-applications of biochar with basanite, peridotite, and concrete. In contrast, RE biochars mostly showed reduced geogenic IC-Sinks for industrial materials, but increased geogenic IC-Sinks for peridotite from accelerated Mg2+ release from thermally activated serpentine. Cation pool analyses revealed that most cations were leached rather than being retained in exchangeable pools of the soil. Overall, our evaluation of synergies arising from ERW-PyCCS combinations for terrestrial CDR highlights material-specific advantages and trade-offs, supporting the recommendation of both single application and co-application of biochar with mineral feedstocks.
- 27 April 2026
- Published by CarbonPlan
Open AccessCarbon dioxide removal efficiency of co-applied and co-pyrolyzed feedstocks for enhanced rock weathering and biochar in a sandy soil
Enhanced rock weathering (ERW) and pyrogenic carbon capture and storage (PyCCS) are promising land based approaches for carbon dioxide removal (CDR), yet their co-deployment remains poorly understood. This study investigates how co-application of minerals with biochar and co-pyrolysing biomass with minerals influence mineral weathering, alkalinity production, and carbon sequestration in a sandy soil with low cation exchange capacity (CEC) and low organic carbon (Corg) content. We compared concrete, steel slag, basanite, serpentinised peridotite, limestone and biochar as pure and co-applications, and rock enhanced biochars (RE-biochars) from dry-mixing and wet-impregnation of biomass and consecutive co-pyrolysis. Downflow columns filled with amended sandy soil were incubated for 75 weeks under elevated pCO2 while monitoring cation fluxes, trace metal release, dissolved organic carbon (DOC) dynamics, and changes in soil CEC. Wet impregnation substantially altered RE-biochar properties by increasing the pyrolysis carbon yield and fraction of highly stable pyrogenic carbon particularly for Mg rich feedstocks. Reduced DOC losses and enhanced alkalinity production, attributed to mineral weathering as the geogenic inorganic carbon sink (IC-Sink), was present for co-applications of biochar with basanite, peridotite, and concrete. In contrast, RE biochars mostly showed reduced geogenic IC-Sinks for industrial materials, but increased geogenic IC-Sinks for peridotite from accelerated Mg2+ release from thermally activated serpentine. Cation pool analyses revealed that most cations were leached rather than being retained in exchangeable pools of the soil. Overall, our evaluation of synergies arising from ERW-PyCCS combinations for terrestrial CDR highlights material-specific advantages and trade-offs, supporting the recommendation of both single application and co-application of biochar with mineral feedstocks.
- Open Access
- 10 January 2026
- Published by Elsevier in Biomass and Bioenergy
- Vol. 209
Kaolin additivation in pulverized wood firing systems – potassium capture, emissions and ash behavior
- 10 January 2026
- Published by Elsevier in Biomass and Bioenergy
- Vol. 209
Open AccessKaolin additivation in pulverized wood firing systems – potassium capture, emissions and ash behavior
- Open Access
- 10 November 2025
- Published by Elsevier in Biomass and Bioenergy
- Vol. 206
Reassessment of the energetic value of lignocellulosic biomass in closed carbon cycles
- 10 November 2025
- Published by Elsevier in Biomass and Bioenergy
- Vol. 206
Open AccessReassessment of the energetic value of lignocellulosic biomass in closed carbon cycles
- Open Access
- 17 June 2025
- Published by Springer Nature in BioEnergy Research
- Vol. 18 (1) , 1-16
Long-Term Continuous Anaerobic Co-digestion of Residual Biomass—Model Validation and Model-Based Investigation of Different Carbon-to-Nitrogen Ratios
Major challenges in using lignocellulosic residues as biogas substrates arise from their high diversity and their typically low nitrogen content, which may not provide sufficient nitrogen for the microorganisms. To investigate to what extent such substrates can be used in biogas plants without extensive pre-treatment, this study presents a 300-day continuous co-digestion of lignocellulosic substrates (i.e., sugarcane reed, lemon, and grape leaves) and goat manure while continuously monitoring various process parameters. The results suggest a stable and effective biogas production at a carbon-to-nitrogen ratio (C/N ratio) of 33, with a production of 244 ± 15 mLN gVS −1 d−1 biogas. At a higher C/N ratio of 43, the process remained stable, but hindrance was encountered. Process failure occurred at a C/N ratio of 52, where a rapid decline in biogas production was observed, accompanied by an increase in the volatile fatty acids to total alkalinity ratio (from < 0.2 to 0.9), a drop in the pH-value (from > 7 to 5.4), and an increased CO2-content of the provided biogas (from > 50% to 43%). The compositional analysis of the digestate suggests an insufficient N-supply and a failure of the carbonate and ammonium buffer systems inside the reactor. The experiment also served to validate a previously developed model based on the individual substrates’ degradation kinetics. With a relative root mean square error rRMSE of 8%, the model adequately predicted biogas production within defined limits. However, it could not anticipate process breakdown at high C/N ratios, highlighting a strong limitation. Graphical Abstract
- 17 June 2025
- Published by Springer Nature in BioEnergy Research
- Vol. 18 (1) , 1-16
Open AccessLong-Term Continuous Anaerobic Co-digestion of Residual Biomass—Model Validation and Model-Based Investigation of Different Carbon-to-Nitrogen Ratios
Major challenges in using lignocellulosic residues as biogas substrates arise from their high diversity and their typically low nitrogen content, which may not provide sufficient nitrogen for the microorganisms. To investigate to what extent such substrates can be used in biogas plants without extensive pre-treatment, this study presents a 300-day continuous co-digestion of lignocellulosic substrates (i.e., sugarcane reed, lemon, and grape leaves) and goat manure while continuously monitoring various process parameters. The results suggest a stable and effective biogas production at a carbon-to-nitrogen ratio (C/N ratio) of 33, with a production of 244 ± 15 mLN gVS −1 d−1 biogas. At a higher C/N ratio of 43, the process remained stable, but hindrance was encountered. Process failure occurred at a C/N ratio of 52, where a rapid decline in biogas production was observed, accompanied by an increase in the volatile fatty acids to total alkalinity ratio (from < 0.2 to 0.9), a drop in the pH-value (from > 7 to 5.4), and an increased CO2-content of the provided biogas (from > 50% to 43%). The compositional analysis of the digestate suggests an insufficient N-supply and a failure of the carbonate and ammonium buffer systems inside the reactor. The experiment also served to validate a previously developed model based on the individual substrates’ degradation kinetics. With a relative root mean square error rRMSE of 8%, the model adequately predicted biogas production within defined limits. However, it could not anticipate process breakdown at high C/N ratios, highlighting a strong limitation. Graphical Abstract
- Open Access
- 19 April 2025
- Published by Elsevier in Renewable Energy
- Vol. 249
Deep eutectic solvent pre-treatment of residual biomass streams – Effects on anaerobic degradability
- 19 April 2025
- Published by Elsevier in Renewable Energy
- Vol. 249
Open AccessDeep eutectic solvent pre-treatment of residual biomass streams – Effects on anaerobic degradability
- Open Access
Energy-Related Assessment of a Hemicellulose-First Concept—Debottlenecking of a Hydrothermal Wheat Straw Biorefinery
A hemicellulose-first approach can offer advantages for biorefineries utilizing wheat straw as it combines lignocellulose fractionation and potentially higher added value from pentose-based hemicellulose. Therefore, a tailored hydrothermal concept for the production of xylooligosaccharides and xylan was investigated. The focus was on assessing the energy requirements and potential improvements based on experimental results. The wheat straw pretreatment and the downstream processing of hemicellulose hydrolysate were modeled at a scale of 30,000 tons of wheat straw dry mass per year. The results confirmed that the hydrothermal concept can be implemented in an energy-efficient manner without the need for additional auxiliaries, due to targeted process design, heat integration and a high solids loading during hydrolysis. The resulting specific energy requirements for pretreatment and hydrolysate processing are 0.28 kWh/kg and 0.13 kWh/kg of wheat straw dry mass, respectively. Compared to thermal hydrolysate processing alone, the combination of a multi-effect evaporator and pressure-driven ultrafiltration can reduce the heating and cooling energy by 29% and 44%, respectively. However, the ultrafiltration requirements (e.g., electrical energy, membrane area and costs) depend heavily on the properties of the hydrolysate and its interactions with the membrane. This work can contribute to the commercially viable ramp-up of wheat straw multi-product biorefineries.
Open AccessEnergy-Related Assessment of a Hemicellulose-First Concept—Debottlenecking of a Hydrothermal Wheat Straw Biorefinery
A hemicellulose-first approach can offer advantages for biorefineries utilizing wheat straw as it combines lignocellulose fractionation and potentially higher added value from pentose-based hemicellulose. Therefore, a tailored hydrothermal concept for the production of xylooligosaccharides and xylan was investigated. The focus was on assessing the energy requirements and potential improvements based on experimental results. The wheat straw pretreatment and the downstream processing of hemicellulose hydrolysate were modeled at a scale of 30,000 tons of wheat straw dry mass per year. The results confirmed that the hydrothermal concept can be implemented in an energy-efficient manner without the need for additional auxiliaries, due to targeted process design, heat integration and a high solids loading during hydrolysis. The resulting specific energy requirements for pretreatment and hydrolysate processing are 0.28 kWh/kg and 0.13 kWh/kg of wheat straw dry mass, respectively. Compared to thermal hydrolysate processing alone, the combination of a multi-effect evaporator and pressure-driven ultrafiltration can reduce the heating and cooling energy by 29% and 44%, respectively. However, the ultrafiltration requirements (e.g., electrical energy, membrane area and costs) depend heavily on the properties of the hydrolysate and its interactions with the membrane. This work can contribute to the commercially viable ramp-up of wheat straw multi-product biorefineries.
- Open Access
- 5 December 2024
- Published by MDPI AG in Preprints.org
Energy-Related Assessment of a Hemicellulose-First Concept – Debottlenecking of a Hydrothermal Wheat Straw Biorefinery
A hemicellulose-first approach can offer advantages for biorefineries utilizing wheat straw as it combines lignocellulose fractionation and potentially higher added value from pentose-based hemicellulose. Therefore, a tailored hydrothermal concept for the production of xylooligosaccharides and xylan is investigated. The focus is on assessing energy requirements and potential improvements based on experimental results. The wheat straw pretreatment and the downstream processing of the hemicellulose hydrolysate are modeled at a scale of 30,000 tons wheat straw dry mass per year. The results confirm that the hydrothermal concept can be implemented in an energy-efficient manner without the need for additional auxiliaries, due to targeted process design, heat integration and high solids loading during hydrolysis. The resulting specific energy requirements for pretreatment and hydrolysate processing are 0.28 kWh/kg and 0.13 kWh/kg of wheat straw dry mass, respectively. Compared to thermal hydrolysate processing alone, the combination of a multi-effect evaporator and a pressure-driven ultrafiltration can reduce heating and cooling energy by 29 % and 44 %, respectively. However, the ultrafiltration requirements (e.g., electrical energy, membrane area, costs) depend heavily on the properties of the hydrolysate and its interactions with the membrane. This work can contribute to the commercially viable ramp-up of wheat straw multi-product biorefineries.
- 5 December 2024
- Published by MDPI AG in Preprints.org
Open AccessEnergy-Related Assessment of a Hemicellulose-First Concept – Debottlenecking of a Hydrothermal Wheat Straw Biorefinery
A hemicellulose-first approach can offer advantages for biorefineries utilizing wheat straw as it combines lignocellulose fractionation and potentially higher added value from pentose-based hemicellulose. Therefore, a tailored hydrothermal concept for the production of xylooligosaccharides and xylan is investigated. The focus is on assessing energy requirements and potential improvements based on experimental results. The wheat straw pretreatment and the downstream processing of the hemicellulose hydrolysate are modeled at a scale of 30,000 tons wheat straw dry mass per year. The results confirm that the hydrothermal concept can be implemented in an energy-efficient manner without the need for additional auxiliaries, due to targeted process design, heat integration and high solids loading during hydrolysis. The resulting specific energy requirements for pretreatment and hydrolysate processing are 0.28 kWh/kg and 0.13 kWh/kg of wheat straw dry mass, respectively. Compared to thermal hydrolysate processing alone, the combination of a multi-effect evaporator and a pressure-driven ultrafiltration can reduce heating and cooling energy by 29 % and 44 %, respectively. However, the ultrafiltration requirements (e.g., electrical energy, membrane area, costs) depend heavily on the properties of the hydrolysate and its interactions with the membrane. This work can contribute to the commercially viable ramp-up of wheat straw multi-product biorefineries.