Tuo Kang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tuo Kang has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Liwei Chen
Shanghai Jiao Tong University
4 shared publications Chenghao Liu
I-Lab, CAS Center for Excellence in Nanoscience, Suzhou Institute of Nano-Tech and Nano-Bionics (SINANO), Chinese Academy of Sciences, Suzhou 215123, P.R. China
3 shared publicationsWei Lu
I-Lab, CAS Center for Excellence in Nanoscience, Suzhou Institute of Nano-Tech and Nano-Bionics (SINANO), Chinese Academy of Sciences, Suzhou 215123, P.R. China
3 shared publications- Yanbin Shen
I-Lab, Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215123, China
3 shared publications - Feng Guo
I-Lab, CAS Center for Excellence in Nanoscience , Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences , Suzhou 215123 , China
2 shared publications Jianghui Zhao
I-Lab, CAS Center for Excellence in Nanoscience , Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences , Suzhou 215123 , China
2 shared publications
Latest Publications
- 28 September 2020
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 142 (42) , 18035-18041
Superionic Conductors via Bulk Interfacial Conduction
Superionic conductors with ionic conductivity on the order of mS cm-1 are expected to revolutionize the development of solid-state batteries (SSBs). However, currently available superionic conductors are limited to only a few structural families such as garnet oxides and sulfide-based glass/ceramic. Interfaces in composite systems such as alumina in lithium iodide have long been identified as a viable ionic conduction channel but practical superionic conductors employing the interfacial conduction mechanism are yet to be realized. Here we report a novel method that creates continuous interfaces in the bulk of composite thin films. Ions can conduct through the interface and consequently the inorganic phase can be ionically insu-lating in this type of bulk interface superionic conductors (BISCs). Ionic conductivities of lithium, sodium, and magnesium ion BISCs have reached 1.16 mS cm-1, 0.40 mS cm-1, and 0.23 mS cm-1 at 25 oC in 25 μm thick films, corresponding to areal conductance as high as 464 mS cm-2, 160 mS cm-2 and 92 mS cm-2, respectively. Ultralow over-potential and stable long-term cycling for up to 5000 hours was obtained for solid-state Li metal symmetric batteries employing Li ion BISCs. This work opens new structural space for superionic conductors and urges for future investigations on detailed conduction mech-anisms and material design principles.
- 28 September 2020
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 142 (42) , 18035-18041
Superionic Conductors via Bulk Interfacial Conduction
Superionic conductors with ionic conductivity on the order of mS cm-1 are expected to revolutionize the development of solid-state batteries (SSBs). However, currently available superionic conductors are limited to only a few structural families such as garnet oxides and sulfide-based glass/ceramic. Interfaces in composite systems such as alumina in lithium iodide have long been identified as a viable ionic conduction channel but practical superionic conductors employing the interfacial conduction mechanism are yet to be realized. Here we report a novel method that creates continuous interfaces in the bulk of composite thin films. Ions can conduct through the interface and consequently the inorganic phase can be ionically insu-lating in this type of bulk interface superionic conductors (BISCs). Ionic conductivities of lithium, sodium, and magnesium ion BISCs have reached 1.16 mS cm-1, 0.40 mS cm-1, and 0.23 mS cm-1 at 25 oC in 25 μm thick films, corresponding to areal conductance as high as 464 mS cm-2, 160 mS cm-2 and 92 mS cm-2, respectively. Ultralow over-potential and stable long-term cycling for up to 5000 hours was obtained for solid-state Li metal symmetric batteries employing Li ion BISCs. This work opens new structural space for superionic conductors and urges for future investigations on detailed conduction mech-anisms and material design principles.
- 27 January 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (7) , 8168-8175
Dendrite-Free Lithium Anodes Enabled by a Commonly Used Copper Antirusting Agent
Li metal is considered as the most promising anode for high energy density secondary batteries due to its high theoretical capacity and low redox potential. However, lithium is prone to form dendrites which will not only cause internal short-circuit but also bring accumulation of “dead Li” and result in fast capacity decay thus its large-scale application is challenging. In this work, we demonstrate that the commonly used metal corrosion inhibitor, benzotriazole (BTA), can be used to modify the Cu foil surface and guide homogeneous Li+ plating/stripping due to the lithiophilic nature of the N atom in the BTA molecule. As a result, the lithium plated on the BTA modified Cu (BTA-Cu) substrate is free of dendrites and a Coulombic efficiency (CE) as high as 99.0% was achieved for Li+ plating/stripping on the BTA-Cu substrate at a current density of 1 mA/cm2. Furthermore, the BTA-Cu foil can be used as an anode to assemble an anode-free cell (BTA-Cu ‖ LFP) and ~73.3% of the initial capacity can be obtained after 50 cycles. Last but not the least, a [email protected] electrode prepared by plating of Li+ on the BTA-Cu substrate can be served as a stable Li anode in a [email protected] ‖ LFP cell and display an average cycled CE of 98.5% at a depth of discharge (DOD) of 33%. This simple method of Li+ plating/stripping behavior regulation could inspire researchers on the development of highly stable lithium metal anode for high energy density batteries.
- 27 January 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (7) , 8168-8175
Dendrite-Free Lithium Anodes Enabled by a Commonly Used Copper Antirusting Agent
Li metal is considered as the most promising anode for high energy density secondary batteries due to its high theoretical capacity and low redox potential. However, lithium is prone to form dendrites which will not only cause internal short-circuit but also bring accumulation of “dead Li” and result in fast capacity decay thus its large-scale application is challenging. In this work, we demonstrate that the commonly used metal corrosion inhibitor, benzotriazole (BTA), can be used to modify the Cu foil surface and guide homogeneous Li+ plating/stripping due to the lithiophilic nature of the N atom in the BTA molecule. As a result, the lithium plated on the BTA modified Cu (BTA-Cu) substrate is free of dendrites and a Coulombic efficiency (CE) as high as 99.0% was achieved for Li+ plating/stripping on the BTA-Cu substrate at a current density of 1 mA/cm2. Furthermore, the BTA-Cu foil can be used as an anode to assemble an anode-free cell (BTA-Cu ‖ LFP) and ~73.3% of the initial capacity can be obtained after 50 cycles. Last but not the least, a [email protected] electrode prepared by plating of Li+ on the BTA-Cu substrate can be served as a stable Li anode in a [email protected] ‖ LFP cell and display an average cycled CE of 98.5% at a depth of discharge (DOD) of 33%. This simple method of Li+ plating/stripping behavior regulation could inspire researchers on the development of highly stable lithium metal anode for high energy density batteries.
- 5 August 2019
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 19 (9) , 6377-6384
Advanced Lithium Metal–Carbon Nanotube Composite Anode for High-Performance Lithium–Oxygen Batteries
The low Coulombic efficiency and hazardous dendrite growth hinder the adoption of lithium anode in high-energy density batteries. Herein, we report a lithium metal–carbon nanotube (Li–CNT) composite as an alternative to the long-term untamed lithium electrode to address the critical issues associated with the lithium anode in Li–O2 batteries, where the lithium metal is impregnated in a porous carbon nanotube microsphere matrix (CNTm) and surface-passivated with a self-assembled monolayer of octadecylphosphonic acid as a tailor-designed solid electrolyte interphase (SEI). The high specific surface area of the Li–CNT composite reduces the local current density and thus suppresses the lithium dendrite formation upon cycling. Moreover, the tailor-designed SEI effectively separates the Li–CNT composite from the electrolyte solution and prevents the latter’s further decomposition. When the Li–CNT composite anode is coupled with another CNTm-based O2 cathode, the reversibility and cycle life of the resultant Li–O2 batteries are drastically elevated.
- 5 August 2019
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 19 (9) , 6377-6384
Advanced Lithium Metal–Carbon Nanotube Composite Anode for High-Performance Lithium–Oxygen Batteries
The low Coulombic efficiency and hazardous dendrite growth hinder the adoption of lithium anode in high-energy density batteries. Herein, we report a lithium metal–carbon nanotube (Li–CNT) composite as an alternative to the long-term untamed lithium electrode to address the critical issues associated with the lithium anode in Li–O2 batteries, where the lithium metal is impregnated in a porous carbon nanotube microsphere matrix (CNTm) and surface-passivated with a self-assembled monolayer of octadecylphosphonic acid as a tailor-designed solid electrolyte interphase (SEI). The high specific surface area of the Li–CNT composite reduces the local current density and thus suppresses the lithium dendrite formation upon cycling. Moreover, the tailor-designed SEI effectively separates the Li–CNT composite from the electrolyte solution and prevents the latter’s further decomposition. When the Li–CNT composite anode is coupled with another CNTm-based O2 cathode, the reversibility and cycle life of the resultant Li–O2 batteries are drastically elevated.
- Open Access
- 12 February 2019
- Published by American Chemical Society (ACS) in ACS Central Science
- Vol. 5 (3) , 468-476
Self-Assembled Monolayer Enables Slurry-Coating of Li Anode
Li metal has long been considered as the ultimate anodic material for high-energy-density batteries. Protection of Li metal in electrochemical cycling and in the manufacturing environment is critical for practical applications. Here, we present the passivation of the Li metal–carbon nanotube (CNT) composite with molecular self-assembly of a long-chain aliphatic phosphonic acid. The dynamics of the self-assembly process is investigated with sum-frequency generation spectroscopy (SFG). The aliphatic phosphonic acid molecules self-assemble on the Li metal surface via the lithium phosphate bonding, while the well-aligned long chains of the molecules help to prevent corrosion of lithium by oxygen and water in the air. As a result, the self-assembled monolayer (SAM) passivated Li–CNT composite displays excellent stability in dry or even humid air, and could be slurry-coated with organic solvents. The resulting slurry-coated Li anode exhibits a high Coulombic efficiency of 98.8% under a 33% depth of discharge (DOD) at a 1C rate in full battery cycling. The concept of molecular self-assembly on Li metal and the stability of the resulting SAM layer open vast possibilities of designed reagents for surface passivation of Li, which may eventually pave the way for practical application of Li metal in secondary batteries.
- 12 February 2019
- Published by American Chemical Society (ACS) in ACS Central Science
- Vol. 5 (3) , 468-476
Open AccessSelf-Assembled Monolayer Enables Slurry-Coating of Li Anode
Li metal has long been considered as the ultimate anodic material for high-energy-density batteries. Protection of Li metal in electrochemical cycling and in the manufacturing environment is critical for practical applications. Here, we present the passivation of the Li metal–carbon nanotube (CNT) composite with molecular self-assembly of a long-chain aliphatic phosphonic acid. The dynamics of the self-assembly process is investigated with sum-frequency generation spectroscopy (SFG). The aliphatic phosphonic acid molecules self-assemble on the Li metal surface via the lithium phosphate bonding, while the well-aligned long chains of the molecules help to prevent corrosion of lithium by oxygen and water in the air. As a result, the self-assembled monolayer (SAM) passivated Li–CNT composite displays excellent stability in dry or even humid air, and could be slurry-coated with organic solvents. The resulting slurry-coated Li anode exhibits a high Coulombic efficiency of 98.8% under a 33% depth of discharge (DOD) at a 1C rate in full battery cycling. The concept of molecular self-assembly on Li metal and the stability of the resulting SAM layer open vast possibilities of designed reagents for surface passivation of Li, which may eventually pave the way for practical application of Li metal in secondary batteries.