Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Stefan P. Meyer has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Study on the Bond Strength of Plastic–Metal Direct Bonds Using Friction Press Joining

    by Stefan P. Meyer, Maren T. Herold, Jan B. Habedank, Michael F. Zaeh

    Friction press joining (FPJ) is an innovative joining process for bonding plastic components and metal sheets without additives in an overlap configuration. This paper focuses on the resulting bond strength. Tensile tests showed that the direct bonds produced by FPJ have either an equivalent or a higher bond strength compared to adhesive bonds. For the material combination of HD-PE and EN AW-6082-T6, an equivalent bond strength was achieved. In contrast, for the material combinations PA6-GF30 with EN AW-6082-T6 and PPS-CF with EN AW-2024-T3, higher tensile shear strengths were achieved via the FPJ technology. In addition to the technical considerations, this paper presents an evaluation of the technological maturity of FPJ. It was found that the basics of the technology are already well developed, and prototypes for showing the applicability have already been manufactured. The last part of this paper deals with the classification of FPJ into the standard for manufacturing processes, according to DIN 8593. The authors suggest a categorization into Activation bonding (item 4.8.1.3). These investigations show the high technical potential of FPJ for joining plastic components with metals.


  • Open Access

    A Holistic, Model-Predictive Process Control for Friction Stir Welding Processes Including a 1D FDM Multi-Layer Temperature Distribution Model

    by Stefan P. Meyer, Sebastian Fuderer, Michael F. Zaeh

    Friction press joining is an innovative joining process for bonding plastics and metals without additives in an overlap configuration. This paper presents for the first time a model-based approach for designing a multi-variable model predictive control (MPC) for friction press joining. For system modeling, a differential equation based on the heat flows was proposed and modeled as a torque-dependent function. With this model, it is possible to consider cross-effects between the axial force and the friction zone temperature. With this theoretical approach, adaptive model-predictive process control was implemented and validated for different material combinations (EN AW-6082-T6; EN AW-2024-T3; PE-HD; PA6-GF30; PPS-CF). It could be shown that the MPC has excellent control accuracy even when model uncertainties are introduced. Based on these findings, a 1D Finite Differential Method multi-layer model was developed to calculate the temperature in the plastic component, which is not measurable in situ (r = 0.93). These investigations demonstrate the high potential of the multi-variable MPC for plastic-metal direct joining.


  • Open Access

    Design, evaluation, and implementation of a model-predictive control approach for a force control in friction stir welding processes

    by Stefan P. Meyer, Christian J. Bernauer, Sophie Grabmann, Michael F. Zaeh

    Friction press joining is an innovative joining process for bonding plastics and metals without additives in an overlap configuration. A model-based approach for the design of an axial force controller for friction press joining is presented in this paper. A closed-loop control was set up on the machining center, in which the plunge depth was used as the controlling variable. In order to support the controller development, a nonparametric dynamic process model was developed via a data-based system identification. Subsequently, various control concepts were designed off-line and verified on the actual system. The most promising ones, a proportional controller, a controller created with the pole placement method, and a model predictive controller, were selected for further investigations. The three controllers were re-evaluated and compared by means of a defined input of disturbance variables and reference variables. The model predictive control (MPC) approach as well as the proportional controller were also tested for model uncertainties. For this purpose, different material combinations were joined using the different controllers. Thereby, it was shown that the MPC controller resulted in smaller standard deviations when encountering large model uncertainties. The investigations demonstrated the high potential of friction press joining of plastic components with metals. The results form the basis for future research, whereby the force can be specified as an additional input parameter instead of the plunge depth.


  • Ageing behavior of thermally joined hybrids of laser pre-treated metal and thermoplastic polymers

    by Niclas Emrich, Stefan P. Meyer, Rüdiger Daub

    Cost-efficient, load bearing and chemically resistant hybrid joints are necessary for future applications within the automotive industry. Thermal joining can be applied to create a direct connection between thermoplastic polymers and metal components and is thus seen as a promising prospect. Yet, the ageing resistance and seal tightness of joints remains uncertain. Within this work, a pulsed laser system (γ = 1064 nm, f=20 kHz) is used to create microscopic random structures on aluminum and copper surfaces. The surface topology is analyzed using optical focus variation. The metal is then connected to different thermoplastic polymers. Polymers are selected with a particular focus on chemical resistance to electrolytes used in modern automotive battery systems. Shear strength and seal tightness for helium gas are measured before and after exposing the joints to humidity and heat. The cause of failure is investigated using REM- and EDX-analysis and by comparing observations from different ageing tests. It is demonstrated that thermoplastic elastomers, such as TPC and TPU, enable long-term resistant hybrid joints (6 N/mm2), with no tendency of a decreasing shear strength.


  • Open Access

    Influence of the laser-based surface modification on the bond strength for friction press joining of aluminum and polyethylene

    by Stefan P. Meyer, Christoph Wunderling, Michael F. Zaeh

    Friction press joining is an innovative joining process for the production of plastic-metal joints without additives, in an overlap configuration. In order to achieve a high bond strength, the metallic joining partner is pretreated with laser radiation. Subsequently, heat is induced by friction and pressure during the joining process, causing the thermoplastic material to melt and adhere to the metallic joining partner. In this work, the temperature distribution during the process in the composite is analyzed and characterized. It was found that the occurring temperatures and temperature differences are not only dependent on the rotational speed, but also on the feed rate. It is also shown that the friction surface temperature can be used as an indirect control variable for a model-based, closed-loop control. Based on these findings, various surface modifications for the metallic joining partner were investigated and analyzed with regard to the maximum strength of the joint. It was observed that the highest tensile shear strength can be achieved with a quasi-chaotic nano structure. In addition, the joining compound was characterized by a thin section, facilitating the identification of specific zones in the joint. These investigations show the high potential for friction press joining of plastics and metals, and form the basis for a model-based control of the joining zone temperature.


  • Friction press joining of dissimilar materials: A novel concept to improve the joint strength

    by Stefan P. Meyer, Christoph Wunderling, Michael F. Zaeh

    The recent affairs about combustion engines in the mobility sector have accelerated the debate on the electrification of automobiles. However, the acceptance of electric cars depends significantly on their range. In order to increase the maximum range of electrified engines, lightweight construction using multi-material design is an essential factor. As a new joining technology, Friction Press Joining (FPJ) in particular offers great potential for joining metals with thermoplastics. The objective of this work is to enable FPJ to combine metals and plastics in a reproducible way. At first, the influence of process and tool parameters on the joining zone temperature and bond strength will be investigated. Based on the results of that, a joining zone temperature model will be developed and its integration into in a temperature control system will be explained. Next, the effect of the joining pressure on the joining strength will be analyzed. In the last part, the joining strength of these bonds, produced by a temperature- and pressure-controlled friction press joining process, will be compared with reference methods.


  • Thermal distortion in surface pretreatment of metal-polymer hybrids using continuous wave laser radiation

    by Christoph Wunderling, Matthias Scherm, Stefan Meyer, Michael F. Zaeh

    Due to the increasing electrification in the automotive industry, materials with a high mass-specific strength are in great demand. In this context, direct thermal joining is an innovative approach to join metals with plastics in the sense of lightweight construction. In order to increase the joint strength, a laser-based surface pretreatment is expedient. The processing with laser radiation generates an inhomogeneous temperature field in the metal, which causes thermal distortion. The deformation can significantly influence the process stability of the subsequent joining process or even prevent its successful execution. Therefore, the thermal distortion in pretreatment was analyzed in order to understand the process behavior and to guarantee excellent joining conditions. For the pretreatment of metal surfaces, infrared continuous wave laser radiation was used. In order to understand the impact of thermal distortion, the metal surface was structured varying the process parameters such as the laser power, the velocity of the laser focal spot, or the applied area energy. Additionally, the structured area size was analyzed. The deformation was analyzed comparing the shape of the metal sheets before and after the processing. Based on the investigations, strategies to reduce distortion were derived and experimentally investigated. Upon the results, it was possible to extract design recommendations for surface structuring using remote ablation cutting. One approach is an oscillating beam guidance which shows significant potential especially in the combination with a high processing velocity.


  • Open Access

    Induction-based joining of titanium with thermoplastics

    by Florian P. Lugauer, Andreas Kandler, Stefan P. Meyer, Christoph Wunderling, Michael F. Zaeh