Mustafa Cansiz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mustafa Cansiz has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Dogay Altinel
Istanbul Medeniyet University
4 shared publications - Gunes Karabulut Kurt
Polytechnique Montreal
3 shared publications - Kürşat Tekbıyık
Department of Electronics and Communications Engineering, stanbul Technical University, stanbul, Turkey
2 shared publications Ali Recai Çelik
1 shared publicationMuhammed Bahattin Kurt
1 shared publication- Muhammed Süzgün
Dicle Elektrik Dağıtım A.Ş.
1 shared publication
Latest Publications
- Open Access
- 4 July 2024
- Published by Dicle Universitesi Muhendislik Fakultesi Muhendislik Dergisi in Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi
- Vol. 15 (3) , 569-580
Design and implementation of multiband microstrip antenna for energy harvesting
Antennas are of great importance in energy harvesting systems. It is possible to collect more energy with RF energy harvesting systems by using multiband antennas. In this study, a microstrip antenna was designed and fabricated for operation at 307 MHz, 1721 MHz, and 5447 MHz frequency bands. The designed multiband antenna with size of 82.05x104.76x1.60 mm3 was optimized for collecting more energy and then, implemented on FR4 substrate. Return loss, voltage standing wave ratio, imaginary and real impedances of the manufactured multiband microstrip antenna were measured by vector network analyzer. The multiband antenna gain was calculated as 2.02 dBi. Furthermore, a good agreement was noted between the measurement and simulation results of the multiband microstrip antenna. As a result, it is determined that the produced multiband microstrip antenna is a useful and suitable antenna for RF energy harvesting circuits.
- 4 July 2024
- Published by Dicle Universitesi Muhendislik Fakultesi Muhendislik Dergisi in Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi
- Vol. 15 (3) , 569-580
Open AccessDesign and implementation of multiband microstrip antenna for energy harvesting
Antennas are of great importance in energy harvesting systems. It is possible to collect more energy with RF energy harvesting systems by using multiband antennas. In this study, a microstrip antenna was designed and fabricated for operation at 307 MHz, 1721 MHz, and 5447 MHz frequency bands. The designed multiband antenna with size of 82.05x104.76x1.60 mm3 was optimized for collecting more energy and then, implemented on FR4 substrate. Return loss, voltage standing wave ratio, imaginary and real impedances of the manufactured multiband microstrip antenna were measured by vector network analyzer. The multiband antenna gain was calculated as 2.02 dBi. Furthermore, a good agreement was noted between the measurement and simulation results of the multiband microstrip antenna. As a result, it is determined that the produced multiband microstrip antenna is a useful and suitable antenna for RF energy harvesting circuits.
- 24 September 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 105 (1) , 91-100
Multiband RF energy harvesting for zero-energy devices
- 24 September 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 105 (1) , 91-100
Multiband RF energy harvesting for zero-energy devices
- 9 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 58 (5) , 3870-3880
Wireless Power Transmission on Martian Surface for Zero-Energy Devices
Exploration of the Red Planet is essential on the way through both human colonization and establishing a habitat on the planet. Due to the high costs of space missions, the use of distributed sensor networks has been investigated to make in situ explorations affordable. Along with this, the devices with ultra-low-power receivers, which are called zero-energy (ZE) devices, can pave the way to further discoveries for the environment of Mars. This study focuses on wireless power transmission to provide the power required by ZE devices on the Martian surface. The main motivation of this study is to investigate whether conventional harvesters and communication units can supply the required power for a long distance. The numerical results show that it is possible to deliver power to ZE devices without utilizing any sophisticated hardware. In addition, the effects of pointing error and dust storms on harvesting performance are investigated. Comprehensive simulation results reveal that harvester selection and design should be done by considering propagation channel and transmitter characteristics.
- 9 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 58 (5) , 3870-3880
Wireless Power Transmission on Martian Surface for Zero-Energy Devices
Exploration of the Red Planet is essential on the way through both human colonization and establishing a habitat on the planet. Due to the high costs of space missions, the use of distributed sensor networks has been investigated to make in situ explorations affordable. Along with this, the devices with ultra-low-power receivers, which are called zero-energy (ZE) devices, can pave the way to further discoveries for the environment of Mars. This study focuses on wireless power transmission to provide the power required by ZE devices on the Martian surface. The main motivation of this study is to investigate whether conventional harvesters and communication units can supply the required power for a long distance. The numerical results show that it is possible to deliver power to ZE devices without utilizing any sophisticated hardware. In addition, the effects of pointing error and dust storms on harvesting performance are investigated. Comprehensive simulation results reveal that harvester selection and design should be done by considering propagation channel and transmitter characteristics.
- Open Access
Wireless Power Transmission on Martian Surface for Zero-Energy Devices
Exploration of the Red Planet is essential on the way through both human colonization and establishing a habitat on the planet. Due to the high costs of space missions, the use of distributed sensor networks has been investigated to make in situ explorations affordable. Along with this, the devices with ultra-low-power receivers, which are called zero-energy (ZE) devices, can pave the way to further discoveries about the environment of Mars. This study focuses on wireless power transmission to provide the power required by ZE devices on the Martian surface. The main motivation of this study is to investigate whether conventional harvesters and communication units can supply the required power for a long distance. The numerical results show that it is possible to deliver power to ZE devices without utilizing any sophisticated hardware. In addition, the effects of pointing error and dust storms on harvesting performance are investigated. Comprehensive simulation results reveal that harvester selection and design should be done by considering propagation channel and transmitter characteristics.
Open AccessWireless Power Transmission on Martian Surface for Zero-Energy Devices
Exploration of the Red Planet is essential on the way through both human colonization and establishing a habitat on the planet. Due to the high costs of space missions, the use of distributed sensor networks has been investigated to make in situ explorations affordable. Along with this, the devices with ultra-low-power receivers, which are called zero-energy (ZE) devices, can pave the way to further discoveries about the environment of Mars. This study focuses on wireless power transmission to provide the power required by ZE devices on the Martian surface. The main motivation of this study is to investigate whether conventional harvesters and communication units can supply the required power for a long distance. The numerical results show that it is possible to deliver power to ZE devices without utilizing any sophisticated hardware. In addition, the effects of pointing error and dust storms on harvesting performance are investigated. Comprehensive simulation results reveal that harvester selection and design should be done by considering propagation channel and transmitter characteristics.
- 10 January 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 104 (3) , 1909-1917
Statistical analysis and modeling of charging time in radio frequency energy harvesting systems
- 10 January 2022
- Published by Springer Nature in Electrical Engineering
- Vol. 104 (3) , 1909-1917
Statistical analysis and modeling of charging time in radio frequency energy harvesting systems
- 30 June 2020
- Published by Springer Nature in Electrical Engineering
- Vol. 102 (4) , 2521-2528
Measurement and analysis of significant effects on charging times of radio frequency energy harvesting systems
- 30 June 2020
- Published by Springer Nature in Electrical Engineering
- Vol. 102 (4) , 2521-2528
Measurement and analysis of significant effects on charging times of radio frequency energy harvesting systems
- Open Access
- 30 July 2019
- Published by Balkan Journal of Electrical & Computer Engineering (BAJECE) in Balkan Journal of Electrical and Computer Engineering
- Vol. 7 (3) , 245-249
Radio Frequency Energy Harvesting with Different Antennas and Output Powers
In this study, the effects of antenna types and output powers on charging times of RF energy harvesting circuit were measured and analyzed in detail. A measurement system which consisting of a signal generator, an RF energy harvesting circuit, antennas and other devices was installed for receiving the measurement samples. According to the measurement results, the shortest charging time was obtained as 0.58 s at a distance of 20 cm, when 6.1 dBi antenna was connected to the RF energy harvesting circuit and the output power of the signal generator was set to 17 dBm. In addition to that, the longest charging time was evaluated as 25.01 s at a distance of 60 cm, when 1 dBi antenna was connected to the RF energy harvesting circuit and the output power of the signal generator was adjust to 14 dBm. As a result, it was determined that increasing of antenna gains and output powers and shortening of distances between signal generator and RF energy harvesting circuit decreased the charging times of the RF energy harvesting circuit in this study.
- 30 July 2019
- Published by Balkan Journal of Electrical & Computer Engineering (BAJECE) in Balkan Journal of Electrical and Computer Engineering
- Vol. 7 (3) , 245-249
Open AccessRadio Frequency Energy Harvesting with Different Antennas and Output Powers
In this study, the effects of antenna types and output powers on charging times of RF energy harvesting circuit were measured and analyzed in detail. A measurement system which consisting of a signal generator, an RF energy harvesting circuit, antennas and other devices was installed for receiving the measurement samples. According to the measurement results, the shortest charging time was obtained as 0.58 s at a distance of 20 cm, when 6.1 dBi antenna was connected to the RF energy harvesting circuit and the output power of the signal generator was set to 17 dBm. In addition to that, the longest charging time was evaluated as 25.01 s at a distance of 60 cm, when 1 dBi antenna was connected to the RF energy harvesting circuit and the output power of the signal generator was adjust to 14 dBm. As a result, it was determined that increasing of antenna gains and output powers and shortening of distances between signal generator and RF energy harvesting circuit decreased the charging times of the RF energy harvesting circuit in this study.
- Open Access
- 1 January 2014
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 20 (8) , 294-299
Measurements of Electric and Magnetic Field Intensities at 50 Hz Mains Frequency and Comparison of Measurement Results to ICNIRP’s Reference Levels for General Public Exposure
Türkiye'nin de içinde bulunduğu birçok ülke tarafından kabul gören Uluslararası İyonlaştırmayan Radyasyondan Korunma Komisyonu (ICNIRP), elektromanyetik alanlara halk ve mesleki maruziyet limitlerini belirleyen ve bu konularda yoğun çalışmalar yapan uluslararası bir komisyondur. ICNIRP elektrik, manyetik ve elektromanyetik alanların biyolojik ve potansiyel sağlık etkilerini incelemek üzere frekans bandını düşük frekans (0-100 Khz) ve yüksek frekans (100 Khz-300 Ghz) bandı olmak üzere ayrı ayrı incelemiş ve farklı kılavuzlar şeklinde yayınlamıştır. Bu çalışmada, düşük frekanslı elektrik ve manyetik alan ölçümleri Diyarbakır İl Merkezi'nin 30 farklı noktasında gerçekleştirilmiştir. Düşük frekans kaynaklı elektrik ve manyetik alan ölçümlerinde ICNIRP'nin belirlemiş olduğu halk maruziyeti limit değerlerini aşan yerlerin olduğu tespit edilmiş ve bununla ilgili durum değerlendirmesi yapılmıştır. Ölçümlerde EHP-50C isimli düşük frekanslı elektrik ve manyetik alan ölçer cihazı kullanılmıştır. Ölçüm sonuçları 6 dakikalık ölçümlerin ortalama değeri alınarak hesaplanmıştır. Ayrıca bir yüksek gerilim hattının altında 60 dakika boyunca elektrik alan şiddeti değerleri ve aynı şekilde manyetik alan şiddeti değerleri kaydedilmiştir. Kayıtlar sonucunda elektrik ve manyetik alan şiddeti değerlerindeki değişimler gözlemlenmiş ve bu değişimler grafik üzerinde gösterilmiştir
- 1 January 2014
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 20 (8) , 294-299
Open AccessMeasurements of Electric and Magnetic Field Intensities at 50 Hz Mains Frequency and Comparison of Measurement Results to ICNIRP’s Reference Levels for General Public Exposure
Türkiye'nin de içinde bulunduğu birçok ülke tarafından kabul gören Uluslararası İyonlaştırmayan Radyasyondan Korunma Komisyonu (ICNIRP), elektromanyetik alanlara halk ve mesleki maruziyet limitlerini belirleyen ve bu konularda yoğun çalışmalar yapan uluslararası bir komisyondur. ICNIRP elektrik, manyetik ve elektromanyetik alanların biyolojik ve potansiyel sağlık etkilerini incelemek üzere frekans bandını düşük frekans (0-100 Khz) ve yüksek frekans (100 Khz-300 Ghz) bandı olmak üzere ayrı ayrı incelemiş ve farklı kılavuzlar şeklinde yayınlamıştır. Bu çalışmada, düşük frekanslı elektrik ve manyetik alan ölçümleri Diyarbakır İl Merkezi'nin 30 farklı noktasında gerçekleştirilmiştir. Düşük frekans kaynaklı elektrik ve manyetik alan ölçümlerinde ICNIRP'nin belirlemiş olduğu halk maruziyeti limit değerlerini aşan yerlerin olduğu tespit edilmiş ve bununla ilgili durum değerlendirmesi yapılmıştır. Ölçümlerde EHP-50C isimli düşük frekanslı elektrik ve manyetik alan ölçer cihazı kullanılmıştır. Ölçüm sonuçları 6 dakikalık ölçümlerin ortalama değeri alınarak hesaplanmıştır. Ayrıca bir yüksek gerilim hattının altında 60 dakika boyunca elektrik alan şiddeti değerleri ve aynı şekilde manyetik alan şiddeti değerleri kaydedilmiştir. Kayıtlar sonucunda elektrik ve manyetik alan şiddeti değerlerindeki değişimler gözlemlenmiş ve bu değişimler grafik üzerinde gösterilmiştir