GZGaokai Zhang

Gaokai Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gaokai Zhang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Bowen Cheng

    Tianjin Key Laboratory of Brine Chemical Engineering and Resource Eco-utilization, College of Chemical Engineering and Materials Science, Tianjin University of Science & Technology, Tianjin 300457, P. R. China

    1 shared publication
  • Gaokao Zhang

    State Key Laboratory of Separation Membranes and Membrane Processes/National Center for International Joint Research on Separation Membranes, Tianjin Polytechnic University, Tianjin, PR China

    1 shared publication
  • Lei Shi

    School of Textile Science and Engineering, Tianjin Polytechnic University, Tianjin 300387, China

    1 shared publication
  • Shengnan Lv

    State Key Laboratory of Separation Membranes and Membrane Processes/National Center for International Joint Research on Separation Membranes, Tianjin Polytechnic University, Tianjin, PR China

    1 shared publication
  • Shubo Wang

    State Key Laboratory of Separation Membranes and Membrane Processes/National Center for International Joint Research on Separation Membranes, Tianjin Polytechnic University, Tianjin, PR China

    1 shared publication
  • Sisi Li

    School of Textile Science and Engineering, Tianjin Polytechnic University, Tianjin 300387, China

    1 shared publication

Latest Publications

  • Fabrication of fibrous microfiltration membrane by pore filling of nanofibers into poly(ethylene terephthalate) nonwoven scaffold

    by Xianlin Xu, Gaokao Zhang, Shubo Wang, Shengnan Lv, Xupin Zhuang

    A nanofibrous microfiltration membrane with high flux, low pressure drop, and high retention capacity was fabricated by pore filling of copolyetherester nanofibers (low-melting-point polyester; melting point of 110℃) into a poly(ethylene terephthalate) nonwoven scaffold. Short low-melting-point polyester nanofibers were anchored on the surface of the poly(ethylene terephthalate) fibers by heat treatment to form a crosslinked nanostructured mesh with very high porosity and high specific surface area. The pore size and distribution of the membranes can be adjusted by varying the loading amount of nanofibers. The resulting membrane not only possessed good interception ability for 5, 3, and 1.3 µm polystyrene microspheres but also exhibited desirable water permeability. In the circulating filtration test, with the accumulation of membrane fouling in the filtration, the membrane was also effective in retaining particulate matter while improving the antipollution ability. These properties are desirable for the effective removal of pollutants on the membrane and restoration of the membrane flux.


  • Open Access

    Solution Blown Nylon 6 Nanofibrous Membrane as Scaffold for Nanofiltration

    by Ya Liu, Gaokai Zhang, Xupin Zhuang, Sisi Li, Lei Shi, Weimin Kang, Bowen Cheng, Xianlin Xu

    In this work, a nylon 6 nanofibrous membrane was prepared via solution blowing technology and followed hot-press as scaffold for nanofiltration. The structure and properties of the hot-pressed nylon 6 nanofibrous membrane (HNM) were studied the effect of hot-pressing parameters and areal densities. Then an ultra-thin polyamide (PA) active layer was prepared by interfacial polymerization on HNM. The effects of nanofibrous scaffolds on the surface properties of ultra-thin nanofiltration membranes and their filtration performance were studied. Results showed that the nylon 6 nanofibers prepared at a concentration of 15 wt % had a good morphology and diameter distribution and the nanofibers were stacked more tightly and significantly reduced in diameter after hot pressing at 180 °C under the pressure of 15 MPa for 10 s. When the porous scaffold was prepared, HNM with an areal density of 9.4 and 14.1 g/m2 has a better apparent structure, a smaller pore size, a higher porosity and a greater strength. At the same time, different areal densities of HNM have an important influence on the preparation and properties of nanofiltration membranes. With the increase of areal density, the uniformity of HNM increased while their surface roughness and pore size decreased, which is beneficial to the establishment of PA barrier layer. With areal density of 9.4 and 14.1 g/m2, the as-prepared nanofiltration membrane has a smoother surface and more outstanding filtration performance. The pure water flux is 13.1 L m−2 h−1 and the filtration efficiencies for NaCl and Na2SO4 are 81.3% and 85.1%, respectively.