Chenwei Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chenwei Wang has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
Tengda Ma
School of Electronics and Information Engineering, Hebei University of Technology, Tianjin, 300130, People's Republic of China
4 shared publicationsYuling Liu
Institute of Microelectronics Technology and Materials, School of Electronic Information Engineering Hebei University of Technology Tianjin China
4 shared publicationsRu Wang
School of Electronics and Information Engineering, Hebei University of Technology, Tianjin 300130, People’s Republic of China
3 shared publications- Ziyan Wang
Faculty of Medicine, Macau University of Science and Technology, 999078, Macao
3 shared publications - Baimei Tan
Hebei university of Technology
2 shared publications - Baohong Gao
Hebei University of Technology, Institute of Microelectronic Technology and Material, Hebei University of Technology, 29 Guangrong Road, Hongqiao District, Tianjin 300130, P.R.China., Tianjin, 300130, CHINA
2 shared publications
Latest Publications
- 1 January 2022
- Published by Elsevier
- p. 359-381
Environmentally sustainable corrosion inhibitors used for electronics industry
- 1 January 2022
- Published by Elsevier
- p. 359-381
Environmentally sustainable corrosion inhibitors used for electronics industry
- 14 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Role of 1-H Carboxyl Benzotriazole as Corrosion Inhibitor for Cobalt “Bulk Step” Cmp in H2O2 Based Alkaline Slurry
Cobalt has been considered as new interconnect metal. In this work, the passivation effect of 1-H Carboxyl Benzotriazole (CBT) on cobalt corrosion during “bulk step” chemical mechanical polishing (CMP) in H 2 O 2 based alkaline slurry was investigated. The result showed that CBT can effectively inhibit the corrosion of cobalt and improve the surface quality after CMP by forming a passivation film on the cobalt surface. Characterization and analysis were given by potential polarization curves, X-ray photoelectron spectroscopy (XPS) and SEM measurements. Meanwhile, the passivation effect of CBT on cobalt was also verified from the mechanical aspect such as working pressure and carrier/platen speeds.
- 14 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Role of 1-H Carboxyl Benzotriazole as Corrosion Inhibitor for Cobalt “Bulk Step” Cmp in H2O2 Based Alkaline Slurry
Cobalt has been considered as new interconnect metal. In this work, the passivation effect of 1-H Carboxyl Benzotriazole (CBT) on cobalt corrosion during “bulk step” chemical mechanical polishing (CMP) in H 2 O 2 based alkaline slurry was investigated. The result showed that CBT can effectively inhibit the corrosion of cobalt and improve the surface quality after CMP by forming a passivation film on the cobalt surface. Characterization and analysis were given by potential polarization curves, X-ray photoelectron spectroscopy (XPS) and SEM measurements. Meanwhile, the passivation effect of CBT on cobalt was also verified from the mechanical aspect such as working pressure and carrier/platen speeds.
- Open Access
- 1 March 2021
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 10 (3) , 034007
Effect of UV Radiation on Oxidation for Ru CMP
As feature size continue to decrease, traditional copper (Cu) interconnections will encounter many problems. Ruthenium (Ru) is selected as a barrier material and even a future interconnection metal material because of its many advantages. However, due to its high hardness and chemical inertness, Ru is difficult to be removed during chemical mechanical polishing (CMP). In this study, the effect of UV-activated potassium persulfate (K2S2O8) on the removal rate of Ru CMP was studied. X-ray photoelectron spectroscopy (XPS) combined with electrochemistry is used to study the removal mechanism and chemical reactions. The results show that ultraviolet rays can enhance the chemical action in the CMP process and change the removal rate. Under the condition of 80 mM, the promotion rate is about 28.01%. When the particle diameter increases to 80 nm, the removal rate is also significantly increased by about 26.36%. Mechanism analysis shows that, on the one hand, it is affected by diffusion-control. On the other hand, the surface RuO3 and K2S2O8 undergo a Fenton-like reaction under UV conditions, which makes the Ru surface loose and porous (Rq = 0.533 nm), so it is easier to remove under mechanical action.
- 1 March 2021
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 10 (3) , 034007
Open AccessEffect of UV Radiation on Oxidation for Ru CMP
As feature size continue to decrease, traditional copper (Cu) interconnections will encounter many problems. Ruthenium (Ru) is selected as a barrier material and even a future interconnection metal material because of its many advantages. However, due to its high hardness and chemical inertness, Ru is difficult to be removed during chemical mechanical polishing (CMP). In this study, the effect of UV-activated potassium persulfate (K2S2O8) on the removal rate of Ru CMP was studied. X-ray photoelectron spectroscopy (XPS) combined with electrochemistry is used to study the removal mechanism and chemical reactions. The results show that ultraviolet rays can enhance the chemical action in the CMP process and change the removal rate. Under the condition of 80 mM, the promotion rate is about 28.01%. When the particle diameter increases to 80 nm, the removal rate is also significantly increased by about 26.36%. Mechanism analysis shows that, on the one hand, it is affected by diffusion-control. On the other hand, the surface RuO3 and K2S2O8 undergo a Fenton-like reaction under UV conditions, which makes the Ru surface loose and porous (Rq = 0.533 nm), so it is easier to remove under mechanical action.
- 3 January 2020
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 9 (3) , 034007
The Effect of Hydroxyethylidene Diphosphonic Acid on the Chemical Mechanical Polishing of Cobalt in H 2 O 2 Based Alkaline Slurries
Cobalt (Co) has caused much interest as an attractive liner material for Cu for the sub-14nm devices. In this paper, the synergetic effect of H 2 O 2 and hydroxyethylidene diphosphonic acid (HEDP) on the Co polishing performance was investigated. The role of HEDP on the Co material removal process in H 2 O 2 based alkaline slurries was intensively investigated by polishing experiments, potentiodynamic measurements, in situ OCP measurements, and the single frequency EIS experiments. The surface chemical composition of Co was studied by X-ray photoelectron spectroscopy (XPS) measurements, and a complexing mechanism was proposed. It was found that the slurries containing 5 wt% SiO 2 , 0.6 wt% H 2 O 2 , and 0.1 wt% HEDP with 300 ppm MBTA at pH 9.5 was a better candidate for Co barrier planarization, with which Cu/Co wafers showed excellent post-polish surfaces and a good RR selectivity. The mean particle size, zeta potential and large particle counts of the desired slurries were obtained with the purpose of evaluating the stability of the slurries. It was observed that the optimized slurry can be stable for at least 7 d.
- 3 January 2020
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 9 (3) , 034007
The Effect of Hydroxyethylidene Diphosphonic Acid on the Chemical Mechanical Polishing of Cobalt in H 2 O 2 Based Alkaline Slurries
Cobalt (Co) has caused much interest as an attractive liner material for Cu for the sub-14nm devices. In this paper, the synergetic effect of H 2 O 2 and hydroxyethylidene diphosphonic acid (HEDP) on the Co polishing performance was investigated. The role of HEDP on the Co material removal process in H 2 O 2 based alkaline slurries was intensively investigated by polishing experiments, potentiodynamic measurements, in situ OCP measurements, and the single frequency EIS experiments. The surface chemical composition of Co was studied by X-ray photoelectron spectroscopy (XPS) measurements, and a complexing mechanism was proposed. It was found that the slurries containing 5 wt% SiO 2 , 0.6 wt% H 2 O 2 , and 0.1 wt% HEDP with 300 ppm MBTA at pH 9.5 was a better candidate for Co barrier planarization, with which Cu/Co wafers showed excellent post-polish surfaces and a good RR selectivity. The mean particle size, zeta potential and large particle counts of the desired slurries were obtained with the purpose of evaluating the stability of the slurries. It was observed that the optimized slurry can be stable for at least 7 d.
- 27 August 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (9) , P509-P515
Controlling of Ru/Cu Removal Rate Selectivity during CMP by Using Ammonium Sulfate and Inhibitor
The controlling of Ru/Cu removal selectivity during the ruthenium-based barrier chemically mechanical polishing (CMP) plays a vital role in controlling the dishing and erosion of the patterned wafer. In this paper, the removal selectivity of Ru to Cu was mainly studied in H2O2-based slurry using ammonium sulfate as a complexing agent and 2,2'-[[(methyl-1H-benzotriazol-1-yl)methyl]imino]diethanol (TT) as an inhibitor. Polishing results indicate that the Ru/Cu removal selectivity can be adjusted from 0.1 to 2.7 by adjusting the concentration of TT or ammonium sulfate in the slurry. The inhibition mechanism of TT was studied in detail by means of electrochemistry and X-Ray photoelectron spectroscopy (XPS). The results show that TT can reduce the corrosion rate and removal rate of Cu by adsorption passivation;on the contrary, TT did not have a significant impact on Ru. In addition, the dishing and erosion of the ruthenium-based pattern wafer were further tested, showing that the slurry having a removal selectivity of barrier (Ru and Ta) to Cu greater than 1.0 can effectively correct the dishing and erosion.
- 27 August 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (9) , P509-P515
Controlling of Ru/Cu Removal Rate Selectivity during CMP by Using Ammonium Sulfate and Inhibitor
The controlling of Ru/Cu removal selectivity during the ruthenium-based barrier chemically mechanical polishing (CMP) plays a vital role in controlling the dishing and erosion of the patterned wafer. In this paper, the removal selectivity of Ru to Cu was mainly studied in H2O2-based slurry using ammonium sulfate as a complexing agent and 2,2'-[[(methyl-1H-benzotriazol-1-yl)methyl]imino]diethanol (TT) as an inhibitor. Polishing results indicate that the Ru/Cu removal selectivity can be adjusted from 0.1 to 2.7 by adjusting the concentration of TT or ammonium sulfate in the slurry. The inhibition mechanism of TT was studied in detail by means of electrochemistry and X-Ray photoelectron spectroscopy (XPS). The results show that TT can reduce the corrosion rate and removal rate of Cu by adsorption passivation;on the contrary, TT did not have a significant impact on Ru. In addition, the dishing and erosion of the ruthenium-based pattern wafer were further tested, showing that the slurry having a removal selectivity of barrier (Ru and Ta) to Cu greater than 1.0 can effectively correct the dishing and erosion.
- Open Access
- 2 August 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (8) , P437-P447
Inhibition Effect of TT-LYK on Cu Corrosion and Galvanic Corrosion between Cu and Co during CMP in Alkaline Slurry
- 2 August 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (8) , P437-P447
Open AccessInhibition Effect of TT-LYK on Cu Corrosion and Galvanic Corrosion between Cu and Co during CMP in Alkaline Slurry
- Open Access
- 30 May 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (5) , P3201-P3205
Effect of Diethylenetriamine Pentaacetate Pentapotassium on Chemical Mechanical Polishing of Cobalt in H2O2 Based Slurry
Cobalt (Co) has been identified as the promising candidate material due to the technology node goes down to 7nm and below. In this paper, the effect of diethylenetriamine pentaacetate pentapotassium (DTPA) on chemical mechanical polishing (CMP) of cobalt (Co) in H2O2 based slurry at pH 9 was studied. The roles of DTPA on the Co material removal process are discussed and a removal mechanism is proposed. The studied result shown that the removal rate (RR) was significantly improved by added DTPA, due to the Co and DTPA reaction Co-DTPA complex. The test results of electrochemical, UV-Vis and XPS also shows the DTPA has obvious chelation for Co.
- 30 May 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (5) , P3201-P3205
Open AccessEffect of Diethylenetriamine Pentaacetate Pentapotassium on Chemical Mechanical Polishing of Cobalt in H2O2 Based Slurry
Cobalt (Co) has been identified as the promising candidate material due to the technology node goes down to 7nm and below. In this paper, the effect of diethylenetriamine pentaacetate pentapotassium (DTPA) on chemical mechanical polishing (CMP) of cobalt (Co) in H2O2 based slurry at pH 9 was studied. The roles of DTPA on the Co material removal process are discussed and a removal mechanism is proposed. The studied result shown that the removal rate (RR) was significantly improved by added DTPA, due to the Co and DTPA reaction Co-DTPA complex. The test results of electrochemical, UV-Vis and XPS also shows the DTPA has obvious chelation for Co.
- 14 May 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (4) , P285-P292
Role of Ammonium Ions in Colloidal Silica Slurries for Ru CMP
The chemical mechanical polishing (CMP) of ruthenium (Ru) based barrier layer has been a pivotal process in the manufacture of a novel copper (Cu) interconnect structure. This paper mainly investigated the role of NH4+ in colloidal silica slurries for Ru CMP. The polishing results show that the Ru removal rate increases with the increasing concentration of NH4+. The influence mechanism of NH4+ on removal rate of Ru was investigated by electrochemistry, scanning electron microscope (SEM) and zeta potential. It is revealed that the NH4+ can promote the surface corrosion rate of Ru by forming a water-soluble Ru-NH4 complex with Ru oxide, meanwhile can also result in the neutralization of the zeta potentials of both silica particles and the Ru surface, and thus can lead to the decrease of the electrostatic repulsive force and the increase of the mechanical abrasion intensity between silica particles and Ru surface. Further, the surface quality of the polished Ru wafer and slurry stability were evaluated, and the results show that the addition of an appropriate amount of NH4+ can achieve a low surface roughness of Ru and a high slurry stability.
- 14 May 2019
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 8 (4) , P285-P292
Role of Ammonium Ions in Colloidal Silica Slurries for Ru CMP
The chemical mechanical polishing (CMP) of ruthenium (Ru) based barrier layer has been a pivotal process in the manufacture of a novel copper (Cu) interconnect structure. This paper mainly investigated the role of NH4+ in colloidal silica slurries for Ru CMP. The polishing results show that the Ru removal rate increases with the increasing concentration of NH4+. The influence mechanism of NH4+ on removal rate of Ru was investigated by electrochemistry, scanning electron microscope (SEM) and zeta potential. It is revealed that the NH4+ can promote the surface corrosion rate of Ru by forming a water-soluble Ru-NH4 complex with Ru oxide, meanwhile can also result in the neutralization of the zeta potentials of both silica particles and the Ru surface, and thus can lead to the decrease of the electrostatic repulsive force and the increase of the mechanical abrasion intensity between silica particles and Ru surface. Further, the surface quality of the polished Ru wafer and slurry stability were evaluated, and the results show that the addition of an appropriate amount of NH4+ can achieve a low surface roughness of Ru and a high slurry stability.
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Effect of BTA Derivative on Reduction of Galvanic Corrosion Between of Ru And Cu During CMP
In this paper, a kind of BTA derivative 2,2'-[[(Methyl-1H-benzotriazol-1-yl)methyl]imino]bisthn ol (TT-LYK) was used to reduce the galvanic corrosion between copper (Cu) and ruthenim (Ru) during chemical mechanical process (CMP). The effect of TT-LYK on the galvanic corrosion current (I GC ) of Ru and Cu in potassium periodate (KIO 4 ) based slurry was investigated. The electrochemical experiment result show that the corrosion currents for Cu/Ru galvanic couple can be decreased in the presence of TT-LYK based on potassium periodate slolutions..
- 1 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Effect of BTA Derivative on Reduction of Galvanic Corrosion Between of Ru And Cu During CMP
In this paper, a kind of BTA derivative 2,2'-[[(Methyl-1H-benzotriazol-1-yl)methyl]imino]bisthn ol (TT-LYK) was used to reduce the galvanic corrosion between copper (Cu) and ruthenim (Ru) during chemical mechanical process (CMP). The effect of TT-LYK on the galvanic corrosion current (I GC ) of Ru and Cu in potassium periodate (KIO 4 ) based slurry was investigated. The electrochemical experiment result show that the corrosion currents for Cu/Ru galvanic couple can be decreased in the presence of TT-LYK based on potassium periodate slolutions..