Florence Delange
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Florence Delange has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Jean-François Silvain
University Bordeaux, CNRS, Bordeaux INP, ICMCB, UMR 5026, Pessac, France
3 shared publications - Yongfeng Lu
Department of Electrical and Computer Engineering, University of Nebraska-Lincoln, Lincoln, NE 68588, USA
3 shared publications Antoine Bident
Univ. Bordeaux, CNRS, Bordeaux INP, ICMCB, Pessac, France
2 shared publicationsChristine Labrugere
CNRS, Univ. Bordeaux, Pessac, France
2 shared publications- Nathalie Caillault
Schneider Electric Industries SAS 28 Henri Tarze St 38000 Grenoble France
2 shared publications - Alain Demourgues
University Bordeaux, CNRS, Bordeaux INP, ICMCB, UMR 5026
1 shared publication
Latest Publications
- Open Access
- 30 November 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (1) , 109-117
Fabrication and characterization of copper and copper alloys reinforced with graphene
The consistent rise in current density within electrical wires leads to progressively more substantial heat losses attributed to the Joule effect. Consequently, mitigating the electrical resistivity of copper wires becomes imperative. To attain this objective, the development of a composite material that incorporates a more conductive reinforcement, like graphene, holds great promise. The conception of a copper/graphene composite using a powder metallurgy-based approach is presented. An optimum graphene quantity of 0.06 vol.% was obtained by calculation in order to limit the phenomenon of overlapping layers. This synthesis technique enables the dispersion of graphene and the meticulous control of the interface through the growth of CuO(Cu) nanoparticles that are tightly bonded to the reinforcement. The increase in the hardness of the various materials with separation of the graphene sheets by ultrasonic treatment (55.3 to 67.6 HV) was obtained. It is an indicator of the correct distribution of the reinforcement. The influence on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, resulting in a modest reduction in electrical resistance of around 1.4%. Nevertheless, for flake copper (2.71 µΩ.cm) and brass (7.66 µΩ.cm), we achieved a more substantial reduction of 2.7% and 10%, respectively. With the improvement of graphene quality, there exists a greater potential for further enhancing the electrical properties.
- 30 November 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (1) , 109-117
Open AccessFabrication and characterization of copper and copper alloys reinforced with graphene
The consistent rise in current density within electrical wires leads to progressively more substantial heat losses attributed to the Joule effect. Consequently, mitigating the electrical resistivity of copper wires becomes imperative. To attain this objective, the development of a composite material that incorporates a more conductive reinforcement, like graphene, holds great promise. The conception of a copper/graphene composite using a powder metallurgy-based approach is presented. An optimum graphene quantity of 0.06 vol.% was obtained by calculation in order to limit the phenomenon of overlapping layers. This synthesis technique enables the dispersion of graphene and the meticulous control of the interface through the growth of CuO(Cu) nanoparticles that are tightly bonded to the reinforcement. The increase in the hardness of the various materials with separation of the graphene sheets by ultrasonic treatment (55.3 to 67.6 HV) was obtained. It is an indicator of the correct distribution of the reinforcement. The influence on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, resulting in a modest reduction in electrical resistance of around 1.4%. Nevertheless, for flake copper (2.71 µΩ.cm) and brass (7.66 µΩ.cm), we achieved a more substantial reduction of 2.7% and 10%, respectively. With the improvement of graphene quality, there exists a greater potential for further enhancing the electrical properties.
- Open Access
- 2 November 2023
- Published by Wiley in ChemistrySelect
- Vol. 8 (41)
Nitrogen Radiofrequency Plasma Treatment of Graphene
The incorporation of nitrogen (N) atoms into a graphitic network such as graphene (Gr) remains a major challenge. However, even if the insertion mechanisms are not yet fully understood, it is certain that the modification of the electrical properties of Gr is possible according to the configuration adopted. Several simulations work, notably using DFT, have shown that the incorporation of N in Gr can induce an increase in the electrical conductivity and N acts as an electron donor; this increase is linked to the amount of N, the sp 2 /sp 3 carbon configuration, and the nature of C−N bonding. Nitrogen radiofrequency (RF) plasma has been used to incorporate N into Gr materials. The RF plasma method shows the possibility to incorporate N‐graphitic nitrogen into Gr after a pre‐treatment with nitric acid. X‐ray photoelectron spectroscopy and Raman spectrometry were used to quantify the functionalized groups. The modifications of the graphene surface chemistry along the amount of N inside the Gr change the chemical environment of N. This method, enabling the incorporation of N inside Gr matrix, opens up a route to a broad range of applications.
- 2 November 2023
- Published by Wiley in ChemistrySelect
- Vol. 8 (41)
Open AccessNitrogen Radiofrequency Plasma Treatment of Graphene
The incorporation of nitrogen (N) atoms into a graphitic network such as graphene (Gr) remains a major challenge. However, even if the insertion mechanisms are not yet fully understood, it is certain that the modification of the electrical properties of Gr is possible according to the configuration adopted. Several simulations work, notably using DFT, have shown that the incorporation of N in Gr can induce an increase in the electrical conductivity and N acts as an electron donor; this increase is linked to the amount of N, the sp 2 /sp 3 carbon configuration, and the nature of C−N bonding. Nitrogen radiofrequency (RF) plasma has been used to incorporate N into Gr materials. The RF plasma method shows the possibility to incorporate N‐graphitic nitrogen into Gr after a pre‐treatment with nitric acid. X‐ray photoelectron spectroscopy and Raman spectrometry were used to quantify the functionalized groups. The modifications of the graphene surface chemistry along the amount of N inside the Gr change the chemical environment of N. This method, enabling the incorporation of N inside Gr matrix, opens up a route to a broad range of applications.
- 20 February 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (11) , 8180-8192
Effect of flake powder metallurgy on thermal conductivity of graphite flakes reinforced aluminum matrix composites
- 20 February 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (11) , 8180-8192
Effect of flake powder metallurgy on thermal conductivity of graphite flakes reinforced aluminum matrix composites