Dishit Paresh Parekh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dishit Paresh Parekh has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Michael D. Dickey
Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695, USA
7 shared publications Collin Ladd
4 shared publications- Christopher B. Cooper
Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
2 shared publications - Ishan D. Joshipura
Department of Chemical and Biomolecular Engineering, North Carolina State University, Raleigh, 27695 North Carolina, United States
2 shared publications Khalil Moussa
2 shared publicationsLazar Panich
Department of Chemical and Biomolecular Engineering, USA
2 shared publications
Latest Publications
- 19 November 2020
- Published by Taylor & Francis
- p. 185-230
Flexible and Stretchable Liquid Metal Electronics
The focus of this chapter is to review the literature on flexible and stretchable electronics fabricated using gallium-based liquid metal alloys. Over the past few decades, gallium-based liquid metal alloys have gathered growing interest due to their application in various soft electronic applications as conductive yet fluidic metals that can be patterned at room temperature. Gallium-based liquid metal alloys have a melting point at or near room temperature and offer a low toxicity as opposed to the conventional liquid metal – mercury, in addition to having negligible vapor pressure and low viscosity. The surface of these metals reacts rapidly with oxygen in air to form a thin surface oxide ‘skin’ that allows these liquids to be deposited in several useful stable shapes despite the destabilizing effects of a large surface tension and gravity. There are several methods to pattern these liquid metals – traditionally using lithography-based subtractive approaches, and unconventionally using 3D printing and other additive techniques. Gallium-based liquid metal alloys have been used for fabricating various electronic structures such as ultrastretchable and self-healing wires, interconnects, and stretchable antennas. Integrating these components, many electronic components have been built such as optical and soft memory devices, reconfigurable circuits, soft diodes, microfluidic pumps, soft strain sensors, capacitors, and circuit boards.
- 19 November 2020
- Published by Taylor & Francis
- p. 185-230
Flexible and Stretchable Liquid Metal Electronics
The focus of this chapter is to review the literature on flexible and stretchable electronics fabricated using gallium-based liquid metal alloys. Over the past few decades, gallium-based liquid metal alloys have gathered growing interest due to their application in various soft electronic applications as conductive yet fluidic metals that can be patterned at room temperature. Gallium-based liquid metal alloys have a melting point at or near room temperature and offer a low toxicity as opposed to the conventional liquid metal – mercury, in addition to having negligible vapor pressure and low viscosity. The surface of these metals reacts rapidly with oxygen in air to form a thin surface oxide ‘skin’ that allows these liquids to be deposited in several useful stable shapes despite the destabilizing effects of a large surface tension and gravity. There are several methods to pattern these liquid metals – traditionally using lithography-based subtractive approaches, and unconventionally using 3D printing and other additive techniques. Gallium-based liquid metal alloys have been used for fabricating various electronic structures such as ultrastretchable and self-healing wires, interconnects, and stretchable antennas. Integrating these components, many electronic components have been built such as optical and soft memory devices, reconfigurable circuits, soft diodes, microfluidic pumps, soft strain sensors, capacitors, and circuit boards.
- Open Access
- 1 February 2019
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 5 (2) , eaat4600
Toughening stretchable fibers via serial fracturing of a metallic core
Stretchable fibers dissipate energy via the sequential fracturing of a metallic core held together by an elastomeric shell.
- 1 February 2019
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 5 (2) , eaat4600
Open AccessToughening stretchable fibers via serial fracturing of a metallic core
Stretchable fibers dissipate energy via the sequential fracturing of a metallic core held together by an elastomeric shell.
- 1 December 2017
- Published by Elsevier in Additive Manufacturing
- Vol. 18, 221-227
Vacuum-filling of liquid metals for 3D printed RF antennas
- 1 December 2017
- Published by Elsevier in Additive Manufacturing
- Vol. 18, 221-227
Vacuum-filling of liquid metals for 3D printed RF antennas
- Top Cited Papers
- 1 September 2017
- Published by Elsevier in Applied Energy
- Vol. 202, 736-745
Flexible thermoelectric generator using bulk legs and liquid metal interconnects for wearable electronics
- 1 September 2017
- Published by Elsevier in Applied Energy
- Vol. 202, 736-745
Top Cited PapersFlexible thermoelectric generator using bulk legs and liquid metal interconnects for wearable electronics
- 7 June 2017
- Published by Wiley in Advanced Materials
- Vol. 29 (30)
3D Printing by Multiphase Silicone/Water Capillary Inks
3D printing of polymers is accomplished easily with thermoplastics as the extruded hot melt solidifies rapidly during the printing process. Printing with liquid polymer precursors is more challenging due to their longer curing times. One curable liquid polymer of specific interest is polydimethylsiloxane (PDMS). This study demonstrates a new efficient technique for 3D printing with PDMS by using a capillary suspension ink containing PDMS in the form of both precured microbeads and uncured liquid precursor, dispersed in water as continuous medium. The PDMS microbeads are held together in thixotropic granular paste by capillary attraction induced by the liquid precursor. These capillary suspensions possess high storage moduli and yield stresses that are needed for direct ink writing. They could be 3D printed and cured both in air and under water. The resulting PDMS structures are remarkably elastic, flexible, and extensible. As the ink is made of porous, biocompatible silicone that can be printed directly inside aqueous medium, it can be used in 3D printed biomedical products, or in applications such as direct printing of bioscaffolds on live tissue. This study demonstrates a number of examples using the high softness, elasticity, and resilience of these 3D printed structures.
- 7 June 2017
- Published by Wiley in Advanced Materials
- Vol. 29 (30)
3D Printing by Multiphase Silicone/Water Capillary Inks
3D printing of polymers is accomplished easily with thermoplastics as the extruded hot melt solidifies rapidly during the printing process. Printing with liquid polymer precursors is more challenging due to their longer curing times. One curable liquid polymer of specific interest is polydimethylsiloxane (PDMS). This study demonstrates a new efficient technique for 3D printing with PDMS by using a capillary suspension ink containing PDMS in the form of both precured microbeads and uncured liquid precursor, dispersed in water as continuous medium. The PDMS microbeads are held together in thixotropic granular paste by capillary attraction induced by the liquid precursor. These capillary suspensions possess high storage moduli and yield stresses that are needed for direct ink writing. They could be 3D printed and cured both in air and under water. The resulting PDMS structures are remarkably elastic, flexible, and extensible. As the ink is made of porous, biocompatible silicone that can be printed directly inside aqueous medium, it can be used in 3D printed biomedical products, or in applications such as direct printing of bioscaffolds on live tissue. This study demonstrates a number of examples using the high softness, elasticity, and resilience of these 3D printed structures.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 41-44
Rapid prototyping of low loss 3D printed waveguides for millimeter-wave applications
Traditional hollow metallic waveguide manufacturing techniques are readily capable of producing components with high-precision geometric tolerances, yet generally lack the ability to customize individual parts on demand or to deliver finished components with low lead times. This paper proposes a Rapid-Prototyping (RP) method for relatively low-loss millimeter-wave hollow waveguides produced using consumer-grade stere-olithographic (SLA) Additive Manufacturing (AM) technology, in conjunction with an electroless metallization process optimized for acrylate-based photopolymer substrates. To demonstrate the capabilities of this particular AM process, waveguide prototypes are fabricated for the W- and D-bands. The measured insertion loss at W-band is between 0.12 dB/in to 0.25 dB/in, corresponding to a mean value of 0.16 dB/in. To our knowledge, this is the lowest insertion loss figure presented to date, when compared to other W-Band AM waveguide designs reported in the literature. Printed D-band waveguide prototypes exhibit a transducer loss of 0.26 dB/in to 1.01 dB/in, with a corresponding mean value of 0.65 dB/in, which is similar performance to a commercial metal waveguide.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 41-44
Rapid prototyping of low loss 3D printed waveguides for millimeter-wave applications
Traditional hollow metallic waveguide manufacturing techniques are readily capable of producing components with high-precision geometric tolerances, yet generally lack the ability to customize individual parts on demand or to deliver finished components with low lead times. This paper proposes a Rapid-Prototyping (RP) method for relatively low-loss millimeter-wave hollow waveguides produced using consumer-grade stere-olithographic (SLA) Additive Manufacturing (AM) technology, in conjunction with an electroless metallization process optimized for acrylate-based photopolymer substrates. To demonstrate the capabilities of this particular AM process, waveguide prototypes are fabricated for the W- and D-bands. The measured insertion loss at W-band is between 0.12 dB/in to 0.25 dB/in, corresponding to a mean value of 0.16 dB/in. To our knowledge, this is the lowest insertion loss figure presented to date, when compared to other W-Band AM waveguide designs reported in the literature. Printed D-band waveguide prototypes exhibit a transducer loss of 0.26 dB/in to 1.01 dB/in, with a corresponding mean value of 0.65 dB/in, which is similar performance to a commercial metal waveguide.
- 21 March 2016
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 16 (10) , 1812-1820
3D printing of liquid metals as fugitive inks for fabrication of 3D microfluidic channels
This paper demonstrates a simple method to fabricate 3D microchannels and microvasculature at room temperature by direct-writing liquid metal as a sacrificial template. The formation of a surface oxide skin on the low-viscosity liquid metal stabilizes the shape of the printed metal for planar and out-of-plane structures. The printed structures can be embedded in a variety of soft (e.g. elastomeric) and rigid (e.g. thermoset) polymers. Both acid and electrochemical reduction are capable of removing the oxide skin that forms on the metal, which destabilizes the ink so that it withdraws from the encapsulating material due to capillary forces, resulting in nearly full recovery of the fugitive ink at room temperature. Whereas conventional fabrication procedures typically confine microchannels to 2D planes, the geometry of the printed microchannels can be varied from a simple 2D network to complex 3D architectures without using lithography. The method produces robust monolithic structures without the need for any bonding or assembling techniques that often limit the materials of construction of conventional microchannels. Removing select portions of the metal leaves behind 3D metal features that can be used as antennas, interconnects, or electrodes for interfacing with lab-on-a-chip devices. This paper describes the capabilities and limitations of this simple process.
- 21 March 2016
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 16 (10) , 1812-1820
3D printing of liquid metals as fugitive inks for fabrication of 3D microfluidic channels
This paper demonstrates a simple method to fabricate 3D microchannels and microvasculature at room temperature by direct-writing liquid metal as a sacrificial template. The formation of a surface oxide skin on the low-viscosity liquid metal stabilizes the shape of the printed metal for planar and out-of-plane structures. The printed structures can be embedded in a variety of soft (e.g. elastomeric) and rigid (e.g. thermoset) polymers. Both acid and electrochemical reduction are capable of removing the oxide skin that forms on the metal, which destabilizes the ink so that it withdraws from the encapsulating material due to capillary forces, resulting in nearly full recovery of the fugitive ink at room temperature. Whereas conventional fabrication procedures typically confine microchannels to 2D planes, the geometry of the printed microchannels can be varied from a simple 2D network to complex 3D architectures without using lithography. The method produces robust monolithic structures without the need for any bonding or assembling techniques that often limit the materials of construction of conventional microchannels. Removing select portions of the metal leaves behind 3D metal features that can be used as antennas, interconnects, or electrodes for interfacing with lab-on-a-chip devices. This paper describes the capabilities and limitations of this simple process.
- 4 June 2014
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9083, 90831D-90831D-10
3-D printing of liquid metals for stretchable and flexible conductors
- 4 June 2014
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9083, 90831D-90831D-10
3-D printing of liquid metals for stretchable and flexible conductors