MGManuel Guzmán

Manuel Guzmán

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Manuel Guzmán has a total of 2 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative study of stress relaxation phenomenological constitutive modeling of carbon black-reinforced natural rubber-based compounds

    by Manuel Alberto Guzmán Sánchez

    The viscoelastic properties of rubber materials are caused by the combination of the dual response as an elastic solid and a viscous fluid. This behavior yields in time-dependent mechanical properties; thus, phenomena such as stress relaxation, creep, energy dissipation, hysteresis, and strain rate are observed. In this study, three different carbon black-reinforced natural rubber compounds were experimentally evaluated under stress relaxation and several linear phenomenological constitutive models were fitted to evaluate their viscoelastic parameters. It was observed that both the elastic and viscous parameters increase in a non-linear relation as the strain and carbon black content increase, and the viscous parameters were dependent on the configuration of the model. The Maxwell and Zener models exhibited fitting values of 76.08 and 95.10%, respectively, while the Wiechert model showed the best fitting values and can be adequately used to estimate the relaxation process of carbon black-reinforced natural rubber applications.


  • Open Access

    Structural, thermal, rheological, morphological and mechanical properties of thermoplastic starch obtained by using hyperbranched polyester polyol as plasticizing agent

    by Manuel Guzmán, Edwin A. Murillo

    En este trabajo, se evaluó el efecto de la proporción de un poliéster poliol altamente ramificado (HBP) de cuarta generación en las propiedades estructurales, térmicas, reológicas, morfológicas y mecánicas de mezclas de almidón de yuca/HBP (TPS). Para este propósito las relaciones de almidón:HBP empleadas para preparar los TPS fueron: 30:70 (TPS30), 40:60 (TPS40) and 50:50 (TPS50). Por análisis infrarrojo (IR) se observó que la presencia de HBP produjo un desplazamiento en las absorciones de los enlaces C-OH, C-O and C-O-C del TPS. El análisis de difracción de rayos X mostró que la cristalinidad del almidón es tipo A y B, las cuales incrementaron con la cantidad de HBP. La temperatura de transición vítrea (Tg) de los TPS, incrementó con el contenido de HBP, pero la estabilidad térmica y la viscosidad (a una frecuencia angular de 1 Hz) presentaron un comportamiento opuesto. El análisis de microscopia de barrido electrónica (SEM), reveló que la estructura granular del almidón no fue completamente desestructurada.


  • Open Access

    Hyperbranched polyester polyol plasticized tapioca starch/low density polyethylene blends

    by Manuel Guzmán, Diego Giraldo, Edwin Murillo

    In this work, low density polyethylene (LDPE)/plasticized starch (TPS) blends were prepared. The TPS employed in this study was obtained by plasticization of tapioca starch with a hyperbranched polyester polyol. Differential scanning calorimetry analysis showed that the melting temperature increased with the TPS content. The opposite effect was exhibited in the crystallization temperature and additional changes were not observed during the heating. X-ray diffraction analysis showed a reduction in intensity of the peak at Bragg’s angle 17.5°, proving a diminution on A type crystallinity with the increasing amount of LDPE. Micrographs obtained by scanning electron microscopy exhibited starch granules without destructure. TPS acted as a filler to LDPE, since the mechanical properties (Young’s modulus and tensile strength) improved ostensibly. The Young’ modulus and tensile strength decreased with the amount of LDPE, however, the elongation at break exhibited an opposite behavior.


  • The properties of blends of maleic‐anhydride‐grafted polyethylene and thermoplastic starch using hyperbranched polyester polyol as a plasticizer

    by Manuel Guzmán, Edwin A. Murillo

    The first aim of this study was to prepare thermoplastic starch (TPS), namely blends of tapioca starch and hyperbranched polyester polyol and to evaluate the hyperbranched polyester polyol (HBP) as a plasticizing agent for tapioca starch. The second aim was to prepare blends of maleic‐anhydride‐grafted low‐density polyethylene (LDPE‐g‐MA) and TPS, and to evaluate the effect of the mass ratio LDPE‐g‐MA/TPS on the structural, thermal, rheological, morphological, and mechanical properties of the blends. The melting and crystallization temperatures of the LDPE‐g‐MA/TPS blends did not correlate well with the ratio of LDPE‐g‐MA/TPS. The blends exhibited a reduction in the A‐type crystallinity and a pseudoplastic rheological behavior. V‐type crystallinity was not observed for neither TPS nor LDPE‐g‐MA/TPS blends. Scanning electronic microscophy provided an evidence for the presence of starch granules in all the blends and for low interaction degree between LDPE‐g‐MA and TPS. Young's modulus and tensile strength of the LDPE‐g‐MA/TPS blends decreased with the decreasing LDPE‐g‐MA/TPS ratio. POLYM. ENG. SCI., 55:2526–2533, 2015. © 2015 Society of Plastics Engineers


  • Open Access

    Funcionalización de polietileno de baja densidad con anhídrido maleico en estado fundido

    by Manuel Guzmán, Edwin A. Murillo

    En este estudio, polietileno de baja densidad (PEBD) fue modificado con anhídrido maleico (AM) en estado fundido usando concentraciones diferentes de peróxido de dicumilo (DCP) (0.25, 0.50, 0.75 y 1.0 %). Los materiales obtenidos fueron caracterizados por contenido de gel, titulaciones ácido-base, análisis infrarrojo (IR), calorimetría de barrido diferencial (DSC), análisis termogravimétrico (TGA), análisis reológico, propiedades mecánicas, dureza y permeabilidad al oxígeno. El análisis reométrico indicó que el tiempo óptimo para obtener las mezclas es alrededor de 7.5 minutos. El análisis IR mostró que el AM fue injertado en el esqueleto del PEBD, el grado de injerto incrementó con el contenido de DCP y el más alto grado de injerto (1.12 ± 0.015 %), fue exhibido por la muestra obtenida empleando la mayor cantidad de DCP (1 %). La estabilidad térmica de las muestras funcionalizadas fue ligeramente mayor que la del PEBD. La cristalinidad de las muestras funcionalizadas fue diferente a la exhibida por el PEBD. El comportamiento reológico presentado por las muestras fue seudoplástico. Las propiedades mecánicas, dureza y la permeabilidad al oxigeno fueron dependientes de la cantidad de DCP y AM injertado en el PEBD