VSViktor Svitlytskyi

Viktor Svitlytskyi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Viktor Svitlytskyi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Consideration of ways to improve the efficiency of deep well drilling

    by Viktor Svitlytskyi, Olga Ivankiv, Nataliia Bilenko

    The object of the research is the composition of the bottom of the drill string when installing screw amplifiers. One of the biggest problems is the place of installation of the screw amplifier in the arrangement of the bottom of the drill string and its influence on the dynamic properties of the rock-crushing tool. The results of the study of the influence of the use of a screw amplifier on the efficiency of drilling deep wells were obtained. According to the results of research, it was determined in particular that the imposition of vibrations often causes a change in the nature of the interaction of the bit with the hole rock, therefore, the installation of the amplifier at different points of the layout will have different effects on the drilling performance. It is shown that the kinetic energy accumulated by the weighted drill pipes, when the amplifier is installed above the bit, is transmitted through the screw mechanism to the rock-destroying tool (bit) and is an operation that leads to an increase in drilling performance. Thanks to the conducted research, it has been proven that the property of the drill string elements and the disturbances of the oscillatory processes of various nature acting on them are related to the dynamic loading of its elements due to the installation of the amplifier in different places of the layout of the bottom of the string. This is due to the fact that the proposed screw amplifier is used with a friction fuse, which causes the rotary movement of the screw under the action of the torque and the translational movement of the nut together with the overbit mass attached to the bit. In most practical cases, especially during deep drilling, bits fail due to the destruction of the rolling bearings of the roller bit, which leads to jamming of the roller bit and leaving them in the holes. For practical use, the proposed design uses a friction fuse, which connects the bit to the drill pipe column through an elastic element. Analytical studies and performed calculations show that this screw amplifier will effectively ensure the destruction of any rocks, especially during overloads without slippage of reaches and be used for the construction of wells in native mining and geological conditions.

  • Open Access

    Determination of the characteristics of drill string vibrations during the drilling process

    by Oleksandr Titlov, Viktor Svitlytskyi, Sergii Iagodovskyi

    The object of research is vibration processes of a certain origin in the drill string with typical design deviations depending on the mode parameters of drilling. A drill string is an oscillating system with an infinite number of degrees of freedom of a multifactor system. An exhaustive study of oscillatory processes in the drill string is impossible neither analytically nor experimentally, due to the specifics of the hole deepening in various rocks, the design of the well, its shape, etc. Therefore, in practice, they try to solve the problems of the dynamics of the drill string for an idealized system and, while preserving the main oscillatory properties, solve some problems of the rod system. The work carried out was aimed at experimental studies of vibrations of the drill string during the drilling process. It is shown that the effectiveness of the use of hydrodynamic cavitation requires the development of methods and devices for intensifying the well drilling process. It is proven that the design of the cavitation generator organically fits into the existing well drilling equipment and allows for the intensification of technological processes with lower specific energy consumption. It is found that all oscillatory processes that occur in the drill string are random in nature and must be considered using the mathematical apparatus of the theory of random oscillations. The study of vibrations during well drilling shows that vibrations can be considered as random stationary processes, since transient modes have a sufficiently short duration for homogeneous rocks with fixed drilling modes. The analysis of the vibrations of the drill string elements based on random oscillations in a number of cases allows to increase the reliability of determining the vibration reliability of the drill string elements. It has been proven that the response of drill string elements to broadband random vibration can be defined as the combined effect of several narrowband random vibrations.

  • Open Access

    Consideration of the issue of regulating low-frequency vibrations of the drill string when drilling with a downhole motor

    by Viktor Svitlytskyi, Sergii Iagodovskyi, Tetiana Sahala

    The object of research is the dynamic processes that occur in the drill string during the deepening of the hole in deep wells. The work is aimed at solving the problem for an idealized system in the form of rod systems while preserving its main oscillatory properties. The nature of oscillatory processes that occur in the drill string during drilling with downhole motors is considered, in some cases it turns out to be very complicated. In the general case, the dynamic process changes according to an aperiodic law, which is superimposed by processes of an oscillating nature with an increasing (damping) nature of the amplitudes of different frequencies. The influence of the torque characteristics of the downhole motor and bit on the development of oscillatory processes in the drill string during well drilling has been theoretically determined. The results of theoretical and experimental studies of oscillatory processes and their interaction with the use of proposed models of hole deepening in the future make it possible to create a simulation model. This model would include taking into account the mode parameters of drilling, the mechanical properties of the rocks to be drilled and the layout of the drill string bottom (DSB). The obtained research results can be applied in practice in the process of designing the structure of the drill string bottom (DSB) with the use of downhole motors, in particular, screw motors, the use of which leads to energy stress, the complication of work processes and structural schemes. As a result, the nature of vibrations changes and the vibration loads on parts of the downhole motor, bits and elements of the drill string are reduced. In the future, it is necessary to take into account the hydrodynamics and the type, as well as the design and parameters of the applied downhole elements for the development of their dynamic models.

  • Open Access

    Investigation of drill string dynamics using probabilistic methods

    by Viktor Svitlytskyi, Sergii Iagodovskyi, Iryna Boshkova

    The object of research is a drill string. The work is directed to the study of the drill string dynamics and its influence on the rock, which is drilled using probabilistic methods. It is shown that the nature of the vibrations of the top of the drill string and the downhole signals are different and have a stationary random character. It is proved that the process at the output of the drill string, taking into account random disturbances, is narrow-band (quasi-harmonic) or close to it. It is found that the energy composition of the spectrum sections and the appearance of resonance peaks and their displacement is directly determined by the physical and mechanical properties of the rocks being drilled, as one of the factors that determines the vibration state of the drill string. Graphs of the spectral density of the power of pitting vibrations are given, showing their amplification at frequencies of 30–40 Hz as the hardness of the rocks being drilled increases. The maximum of the power density bending curve shifts towards low frequencies. There is a «mutual convergence» of the maxima of the power spectral density of the oscillations of the top and bottom of the drill string. It is shown that an important feature of drill string vibrations in the process of drilling with ball bits is that the intensity of vibrations of the top of the drill string passes with frequencies close to low frequencies, and the vibrations of the bottom of the string – to high frequencies. It is determined that the process at the output of the drill string, taking into account random disturbances, is narrow-band (quasi-harmonic) or close to it. As a result, the assumption of a narrow band at the output of the system, which is the basis of theoretical research, is justified. It is proven that the drill string, as a system with liquid filling under pressure, is more stable compared to a hollow structure. The washing liquid, in this case, plays the role of a dynamic absorber.

  • Open Access

    Effect of vibration dampers on the dynamic state of a drill string

    by Viktor Svitlytskyi, Sergii Iagodovskyi, Nataliia Bilenko

    The object of research is the drill string bottom structure using the correcting devices of drilling modes to control the dynamics of the drill string. The work is aimed at the study of longitudinal, torsional and transverse oscillations when adjusting the axial load on the bit by using a drilling shock absorber with a two-link characteristic. A dynamic model of the drill string during the drilling process is presented, which is a concentrated-continuous nonlinear system that interacts with the ball bit and the downhole engine as a source of energy. It is shown that elastic oscillations of all types affect the interaction of the bit with the outcrop rock. In order to evaluate drilling performance, it is necessary to take into account not only longitudinal, torsional and transverse oscillations, but also parametric oscillations, which are associated with the deformation of the weighted drill pipe under axial loads and during its rotation in the process of deepening the hole. It was found that transverse vibrations of weighted drill pipes, as a flexible element, during the drilling process are, as a rule, parametric in nature. They lead to the appearance of additional stresses in the elements of the column and, as a result, to the acceleration of their destruction and accelerated wear of the bit arms and rolling bearings. It is proved that in the future, for the development of dynamic models, it is necessary to take into account their hydrodynamics and the type, design and parameters of the applied punching elements. The obtained research results can be applied in practice in the process of designing the structure of the drill string bottom structure (DSBS) using correcting devices of drilling modes to control the dynamics of the drill string, by using a drilling shock absorber with a two-link characteristic in order to correct the axial load on the bit.


  • Open Access

    Adjustment of the axial load on the bit when hole deepening by using the screw mechanism

    by Viktor Svitlytskyi, Tetiana Sahala

    The object of the research is a screw mechanism for adjusting the axial load on the bit during a hole deepening. Mathematical modeling of dynamic processes that occur in the drill string during the hole deepening in deep wells is considered. It is shown that in the process of hole deepening, the longitudinal oscillations are proportional in their intensity to the torsional ones. Obtained boundary conditions for mathematical models of the column with the use of a shock absorber or a screw amplifier. In the course of research, it was found that the screw working mechanism of the axial load creates a relationship between the axial load on the bit and the torque on the screw. This makes it possible to install safety devices that limit the torque of the drive shaft (reciprocating engine, rotor). It is shown that various types of energy supplied to the punch, which are transformed by the punching motor and amplified due to the axial (screw) amplifier installed above the bit, ensure the rotary-progressive movement of the ball bit and increase the drilling performance. It was determined that the obtained dependencies take into account the change in time of the axial load and torque depending on the parameters of the axial amplifier and the geological and technical conditions of drilling and the arrangement of the bottom of the drill string. The research results will be useful to scientists and specialists of the oil and gas industry during the physical modeling of the processes of adjusting the axial load on the bit during a hole deepening by using a screw mechanism.

  • Open Access

    Increasing the filtration characteristics of rocks in areas of high temperatures

    by Yuliia Kovalchuk, Viktor Svitlytskyi, Olga Ivankiv, Valentin Shinkarenko, Irуna Boshkova

    One of the important problems of the oil and gas industry is the decrease in the production characteristics of wells in fields that are at the final stage of development. In addition, the drop in well production below their potential and the decrease in hydrocarbon recovery factors are often due to the deterioration of the reservoir properties of rocks in the process of drilling in productive formations, well workover, as well as the imperfection of production processes and means of their implementation. The object of research is the technology of treatment of the bottomhole formation zone with non-acidic systems based on ammonium salts for the intensification of hydrocarbon production. The paper considers a number of methods that allow solving the above problems, taking into account their complexity, efficiency and duration of the positive effect of processing. The main acid methods of influencing the bottomhole formation zone and their modifications are analyzed. The authors, using the results of the research and experience gained, proposed a non-acidic system of chemical treatment of oil and gas wells based on ammonium salts. Their influence on the rocks occurs more long-term and does not lead to the destruction of reservoirs. During the research, physical, chemical, physicochemical methods and techniques developed by the authors for processing and analyzing field data, statistical methods for processing experimental studies were used. Modeling of deep processes was carried out on the installation developed and created by the authors. The mechanism of interaction of ammonium salt solutions with terrigenous and carbonate rocks is revealed. Experimental studies have confirmed and theoretically substantiated the effectiveness of the use of ammonium salts to improve the filtration characteristics of reservoirs. The effect of ammonium salt solutions on the change in the permeability of sandy and carbonate reservoirs in the Dnipro-Donetsk depression (DDD, Ukraine) has been studied. And also a mathematical model of the process of increasing the permeability of rocks during their dissolution by the studied chemical reagents was created. The mathematical model is available for its wide application in the practice of technological calculations and designing measures for the stimulation of oil and gas production.

  • Open Access

    Research of the pulsating flow of drilling fluid in the drill string

    by Viktor Svitlytskyi, Irina Boshkova

    The object of research is the pulsating flow of drilling fluid in the drill string. One of the most problematic places is pressure loss due to friction forces distributed along the length of the flow and concentrated in its nodes (threaded joints and pipe bends). In the course of the study, transformation methods were used that allow the drill string to be represented in the form of straight pipes – elements with distributed parameters connected by different inhomogeneities. This makes it possible to reduce the characteristics of the pulsating flow of the drilling fluid to the determination of the lumped parameters of the inclusions, the limiting conditions at the beginning and end of the drill pipes, as homogeneous sections of the drill string. In turn, pressure losses in the drill string during rotary drilling were divided into two types of losses. These are losses along the entire length of the column (flow) and local pressure losses, which are obtained only in certain places of the liquid flow (for example, tool joints, etc.), due to the fact that the flow suffers local deformation. It has been found that from a technological point of view, the most favorable well diameter is the one at which the flow resistance in the pipes is equal to the resistance in the annulus. This is due to the fact that during the flow of the drilling fluid, the speed of the turbulent flow decreases only at the walls of the pipe. Therefore, under the action of centrifugal forces on pipe bends, as in heterogeneities, when local pressure losses occur due to separation of the transit flow, the pipe diameter narrows due to the accumulation of solid particles in whirlpool zones and flow velocities. With a smooth turn of the pipe, the specified separation may be absent. In this case, local pressure losses are largely due to the occurrence of a «steam vortex» at the turn (a helical movement caused by the action of inertial forces). Therefore, a necessary condition for rotary drilling is the continuous circulation of the flushing solution, the complete or partial cessation of which makes further drilling impossible. In this case, the drilling process slows down or leads to an accident. This is due to the accumulation of the hard phase in the places where whirlpools appear. The research results will be useful to scientists and specialists in the oil and gas industry in the physical modeling of well flushing processes in the process of drilling and designing technological flushing processes.

  • Open Access

    Use of the energy of parametric oscillations to improve drilling indices

    by Odessa National Academy Of Food Technologies, V Svitlytskyi, P Ohorodnikov, International Scientific-Technical University named after Academician Yuri Bugay, Yu Kovalchuk, Kyiv National University of Construction and Architecture