Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ali Basha has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Behavior of Rocket Piles Embedded in Sand under Static and Quasi-Static Cyclic Loading

    by Mohamed Elsiragy, Waseim Azzam, Ali Basha

    Pile foundations used in marine and onshore structures are often exposed to repeated axial loading, which can reduce their capacity and increase settlement over time. To address this issue, this study aims to evaluate the performance of rocket piles in sand and to understand how modifying pile geometry can enhance axial capacity under both static and quasi-static cyclic loading. A series of 1-g physical model tests were carried out to investigate the influence of sand relative density, pile slenderness ratio (L/D), fin-length ratio (Lf/L), fin-width ratio (b/D), fin location along the shaft, and surface roughness (Ra) on load–settlement behavior. The experimental results show that adding fins to the pile shaft significantly increases ultimate load capacity and reduces settlement compared to conventional smooth piles. The improvement is particularly noticeable under quasi-static cyclic loading, where fins help mobilize greater shaft resistance and limit the accumulation of settlement. Furthermore, larger fin-width and fin-length ratios provide greater performance enhancement. The main contribution of this study is the experimental evaluation of rocket piles under cyclic conditions and the development of practical design charts that allow engineers to estimate load improvement and settlement reduction based on fin geometry and surface characteristics, offering a more economical and efficient foundation solution in sandy soils.

  • Open Access

    Structural Behavior of Ground-Supported Concrete Slabs Subjected to Repeated Drop-Weight Impacts

    by Usama Heneash, Alireza Bahrami, Mohamed Ghalla, Galal Elsamak, Ayah A. Alkhawaldeh, Ali Basha

    Cast-in-place ground-supported concrete slabs (GSCSs) are used as floors in many facilities such as factories, workshops, garages, and airports (i.e., rigid pavements). These slabs may be subjected to repeated impact loads caused by vehicle loads, the dropping of heavy loads, and aircraft landing loads on runways. This research presents an experimental and numerical study to investigate the behavior of these slabs under impact loads. The experimental program consists of 18 concrete slabs with dimensions of 400 mm × 400 mm × 100 mm. Some variables were studied experimentally, such as the reinforcement ratio of these slabs and the amount of the impact force (represented by the drop height). Unreinforced slabs and slabs reinforced with steel reinforcement or a geogrid mesh made of knitted polyester ribs were tested. ABAQUS software was employed to study the failure mode and crack distribution of these slabs numerically. The accuracy of the proposed numerical model was verified by modeling the tested slabs and comparing the numerical results with the experimental results. From the study results, it is clear that the reinforcement significantly improves the impact performance of GSCSs, transforming their failure behavior from brittle to more ductile and tough. The combined use of impact strength and ductility factors provides an integrated measure of slab performance, offering valuable guidance for the design of protective structures, pavements, and industrial flooring under impact loading.

  • Open Access

    Applicability of 3D laser scanning and close-range photogrammetry for geotechnical laboratory tests

    by Ali M. Basha, Hany El Naggar, Mohamed M. Sherif, Mohamed H. Zakaria

    Non-contact surveying strategies such as terrestrial laser scanning (TLS) and digital close-range photogrammetry (DCRP), have recently become popular as surveying techniques due to their rapid deployment and high accuracy. The critical issue that researchers typically face is the limited number of LVDTs or dial gauges available in laboratories, and occasionally it might be physically challenging to install several gauges in the testing facilities. Consequently, the primary objective of this paper is to examine the present viability and benefits of employing TLS and DCRP techniques in monitoring geotechnical applications. Calibration of these methods was performed through two laboratory tests: (1) monitoring of secant pile walls (SPW) as well as the soil movements; and (2) axial compression tests on SPW. The findings reveal that the discrepancy between traditional measurement methods and the TLS approach is less than 3.0%, whereas the difference between traditional methods and DCRP is under 1.8%. Furthermore, both DCRP and TLS techniques are capable of precisely tracking initial deformations, geometric irregularities, deficiencies in the samples (including pre-buckling phenomena), and deformations of the soil tank at each stage of loading. In conclusion, TLS and DCRP methods were found to offer accurate and advantageous alternatives for geotechnical monitoring, notably their capacity for the automatic collection and analysis of an unlimited number of measurement points.


  • Open Access

    Mitigating Settlement and Enhancing Bearing Capacity of Adjacent Strip Footings Using Sheet Pile Walls: An Experimental Approach

    by Ali M. Basha, Ahmed Yousry Akal, Mohamed H. Zakaria

    In construction, closely spaced footings cause stress interactions that impact bearing capacity, settlement, and stability. This study experimentally evaluates the role of sheet pile walls (SPWs) in improving the performance of two adjacent strip footings—an existing footing and a newly placed footing—on sandy soil. The influence of SPW penetration depth (Ls) and center-to-center spacing between footings (X) on settlement and bearing resistance under vertical loads was investigated. Experiments were conducted in a large-scale soil tank (330 × 30 cm, depth 210 cm), with X ranging from 300 mm to 1000 mm and SPW lengths varying from 0 mm to 1500 mm. The results show that SPWs significantly enhance foundation performance by reducing settlement and increasing bearing capacity. When Ls/B = 6, the settlement of the new footing (F1) decreases by 48%, while the existing footing (F2) sees reductions of 47%, 67%, and 77% at Ls/B = 3, 4, and 5, respectively, under 500 kN/m2 stress. The bearing capacity of F1 increases by 53% when X = 300 mm, demonstrating strong interference effects. Conversely, the F2 settlement increases as X decreases, with a 96% rise at X = 300 mm, but it stabilizes at Ls/B = 5. SPWs also shift failure from general shear to punching shear, modifying soil–structure interaction. These findings highlight the effectiveness of SPWs in mitigating settlement, enhancing load-bearing capacity, and optimizing foundation design in closely spaced footing systems. The results suggest that an SPW length-to-footing width ratio (Ls/B) between 4 and 5 is optimal for minimizing settlement and improving stability, with only a slight difference in effectiveness between these two ratios.


  • Open Access

    Behavior of under-reamed piles under inclined uplift loads in sand

    by Mohamed Sakr, Ahmed Nasr, Mohamed Khaffaf, Ali Basha

    Under-reamed piles are deep bored cast-in-situ concrete piles with single or multiple bulbs formed by enlarging the pile shaft. Such piles are best suited to soils with significant ground movement as a result of seasonal variations, filled up ground, soft soil layers, and loose sand. These piles also improve bearing and uplift capacities, as well as anchorage at greater depths. This paper aims to investigate and analyze the behavior of under-reamed piles under inclined tension loads, as well as to compare the results with regular piles. Single and double under-reamed piles with bulb diameter ratios of 2 and 3 were used as model piles. These piles were embedded in sand with relative densities of 30, 50, and 80%. The tension load was applied at zero eccentricity above the soil surface with inclination angles of 15º, 30º, 45º, 60º, 75º, and 90º with respect to the horizontal direction. The results indicated that the ultimate inclined tension capacity of the under-reamed pile increased as sand relative density, number of bulbs, and bulb diameter ratios increased. Furthermore, when the inclination load angle decreased, the ultimate tension capacity increased due to the generated passive earth pressure in front of the pile. The horizontal load component of the inclined load has more effect on the axial capacity; and this effect decreases with the increase in sand relative density. Finally, a theoretical equation was proposed to estimate the under-reamed pile’s ultimate inclined uplift capacity. This equation correlated well with the experimental results as R2 = 0.91: 0.96.


  • Open Access

    Utilization of Sand Cushion for Stabilization of Peat Layer Considering Dynamic Response of Compaction

    by Ali Basha, Waseim Azzam, Mohamed Elsiragy

    Soft peat soils are located in many zones and at a given depth all over the world and are characterized by their low shear strength and high settlement. It can also cause progressive failure of roads, embankments, and foundations. Sand cushioning is the most beneficial technique used to relieve the stress transmitted to the peat layer to mitigate any deformation and shear failure. In this research, a field study of a road with a soft peat layer located at a depth 4m below the ground surface is carried out. The plate load test is conducted on three cases over the peat layer using sand cushions with and without reinforcement. The results were compared with plate footing on the surface of the road without stabilization. The field tests of the improved technique were verified and deeply analyzed using the numerical program Plaxis. The finite element analysis mainly sheds light on the simulation of the dynamic response that represents the compaction of the sand cushion over the peat layer. A series of numerical models has been done considering the effect of repeated load compaction on the adopted sand cushions with and without reinforcement. The numerical analysis is directed to show the effect of repeated loads of compaction equipment that were used on decreasing the stress over the peat layer. The results showed that the composite compacted cushion with both a higher number of cycles and stress has a great effect on relieving the stresses transmitted to the face of the peat. As a result, the footing capacity is increased with less deformation. Doi: 10.28991/CEJ-2024-010-04-011 Full Text: PDF


  • Predicting the Maximum Axial Capacity of Secant Pile Walls Embedded in Sandy Soil

    by Ali M. Basha, Mohamed H. Zakaria, Maher T. El-Nimr, Mohamed M. Abo-Raya


  • Open Access

    Application of GIS Models in Determining the Suitable Site for a Solid Waste to Energy Plant in an Urban Area

    by Ali Basha, Ahmed Salem, Wael Mostafa, Magda H. Farhan

    This paper deals with the establishment of a solid waste-to-energy plant that significantly reduces the volume of solid waste and produces electricity at the same time. Thirteen criteria have been identified to locate the station based on environmental, economic, and social factors to avoid its negative impacts. These criteria were addressed by combining a Multi Criterion Decision Making (MCDM) method based on the GIS software. This study aims to establish a MCDM system based on the classical AHP and validated by the fuzzy AHP method. The findings revealed that using the classical AHP and fuzzy AHP methods, there was no significant difference in decision-making between the two methods. The importance of the criteria under study has been identified based on the judgments of experts; a questionnaire was designed and conducted electronically, which was collected with the help of a weighted overlay GIS model. This technique combines multiple reclassified data in ArcGIS 10.8 software to overlay criteria layers with different weights to create a composite map of suitability categories across the study area. The outcomes revealed that 96.76% of the study area is unsuitable for establishing the station, 1.36% is moderately suitable, and 0.04% is only very suitable for station site selection. Doi: 10.28991/CEJ-2024-010-01-011 Full Text: PDF