Manoj A. Waghmare
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Manoj A. Waghmare has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Mohan Vithalrao Aware
Department of Electrical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
9 shared publications - Bhimrao S. Umre
Department of Electrical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
7 shared publications - Anup Kumar
Electrical Engineering Department, Visvesvaraya National Institute of Technology, Nagpur, India
6 shared publications Bhimrao S. Umre
Department of Electrical Engineering Visvesvaraya National Institute of Technology Nagpur Maharashtra India
3 shared publications- Atif Iqbal
Department of Electrical Engineering, Qatar University, Doha, Qatar
2 shared publications - Prachi Salodkar
Shree Ramdeobaba College of Engineering and Management
2 shared publications
Latest Publications
- 18 December 2025
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (8) , 4223-4234
Realizing Trade‐OFFs in Virtual Voltage Vector Based Model Predictive Control of 3 ∅$ \varnothing $ to 6 ∅$ \varnothing $ MC to Suppress the Common Mode VoltageThe impact of common mode voltage (CMV) on induction motor life is significant under non‐sinusoidal terminal voltage. In the advent of matrix converters for multi‐phase drives pose a challenge not only to reduce CMV but also to maintain the load current total harmonic distortion (THD) within the acceptable limits. Hence, the matrix converter (MC) performance is attributed to CMV reduction, load current THD minimization and supply side UPF maintenance which together is difficult to attend without any trade‐off. This paper presents a three‐phase to six‐phase matrix converter ( MC) with virtual vector‐based predictive control. In the classical predictive control selective utilization of the available voltage vectors, could lead to CMV reduction at the cost of the increase in the load current THD. The proposed predictive control is derived with selective virtual voltage vector formation to reduce the CMV while maintaining the load current THD within the limits. The trade‐off between CMV and THD is achieved by using a decisive weighting factor in the cost function. The performance of the MC, such as efficiency improvement with supply side unity power factor (UPF) is also achieved. This control algorithm is executed using a low‐cost dsPIC processor and verified experimentally to validate the effectiveness of the proposed algorithm.
- 18 December 2025
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 54 (8) , 4223-4234
Realizing Trade‐OFFs in Virtual Voltage Vector Based Model Predictive Control of 3 ∅$ \varnothing $ to 6 ∅$ \varnothing $ MC to Suppress the Common Mode VoltageThe impact of common mode voltage (CMV) on induction motor life is significant under non‐sinusoidal terminal voltage. In the advent of matrix converters for multi‐phase drives pose a challenge not only to reduce CMV but also to maintain the load current total harmonic distortion (THD) within the acceptable limits. Hence, the matrix converter (MC) performance is attributed to CMV reduction, load current THD minimization and supply side UPF maintenance which together is difficult to attend without any trade‐off. This paper presents a three‐phase to six‐phase matrix converter ( MC) with virtual vector‐based predictive control. In the classical predictive control selective utilization of the available voltage vectors, could lead to CMV reduction at the cost of the increase in the load current THD. The proposed predictive control is derived with selective virtual voltage vector formation to reduce the CMV while maintaining the load current THD within the limits. The trade‐off between CMV and THD is achieved by using a decisive weighting factor in the cost function. The performance of the MC, such as efficiency improvement with supply side unity power factor (UPF) is also achieved. This control algorithm is executed using a low‐cost dsPIC processor and verified experimentally to validate the effectiveness of the proposed algorithm.
- 12 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 21 (3) , 2413-2421
Common-Mode Voltage Reduction Technique for $1\emptyset \ \text{to}\ 6\emptyset $ Matrix Converter Using Primary-Secondary Voltage Vector CombinationsThe emerging need of matrix converter (MC) is due to the existence of large dc-bus capacitors in multistage (ac–dc–ac) conversion from single-phase $( {1\emptyset } )$ to multiphase $( {m\emptyset } )$ system. The fundamental operation of MC with an appropriate voltage transfer ratio (VTR) is to maintain the supply side unity power factor. The limiting operational constraint is common-mode voltage (CMV) appearing across the load neutral and supply side return path due to discrete and impulsive converter switching. The proposed space vector modulation (SVM) approach is based on the two large voltage vectors selected as primary voltage vectors in a given sector to synthesize the reference voltage vector. From the vertically opposite plane of the selected primary voltage vectors, three voltage vectors are grouped as a secondary voltage vectors. To obtain the volt-second balance, null voltage vector activation time is distributed amongst the selected primary and secondary voltage vectors. The proposed control maintains a VTR of 0.519 in $1\emptyset {\bm{\ }}to{\bm{\ }}6\emptyset $ MC conversion while reducing the CMV up to one-third peak of the supply voltage. This proposed SVM is implemented using a low-cost digital signal processor with a laboratory prototype of $1\emptyset {\bm{\ }}to{\bm{\ }}6\emptyset {\bm{\ }}\text{MC}$ to validate the reduced CMV claim.
- 12 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 21 (3) , 2413-2421
Common-Mode Voltage Reduction Technique for $1\emptyset \ \text{to}\ 6\emptyset $ Matrix Converter Using Primary-Secondary Voltage Vector CombinationsThe emerging need of matrix converter (MC) is due to the existence of large dc-bus capacitors in multistage (ac–dc–ac) conversion from single-phase $( {1\emptyset } )$ to multiphase $( {m\emptyset } )$ system. The fundamental operation of MC with an appropriate voltage transfer ratio (VTR) is to maintain the supply side unity power factor. The limiting operational constraint is common-mode voltage (CMV) appearing across the load neutral and supply side return path due to discrete and impulsive converter switching. The proposed space vector modulation (SVM) approach is based on the two large voltage vectors selected as primary voltage vectors in a given sector to synthesize the reference voltage vector. From the vertically opposite plane of the selected primary voltage vectors, three voltage vectors are grouped as a secondary voltage vectors. To obtain the volt-second balance, null voltage vector activation time is distributed amongst the selected primary and secondary voltage vectors. The proposed control maintains a VTR of 0.519 in $1\emptyset {\bm{\ }}to{\bm{\ }}6\emptyset $ MC conversion while reducing the CMV up to one-third peak of the supply voltage. This proposed SVM is implemented using a low-cost digital signal processor with a laboratory prototype of $1\emptyset {\bm{\ }}to{\bm{\ }}6\emptyset {\bm{\ }}\text{MC}$ to validate the reduced CMV claim.
- 22 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9839-9852
Modified Single-Stage Single-Phase to Multiphase Matrix Converter for Extended Low Output Power Frequency Operation
Practical applicability of the single-phase (1∅) power supplied conventional single-stage matrix converter (SSMC) to synthesize multi-phase (m∅) power is limited to very low frequency (3 to 5 Hz) output. In this paper, a modified SSMC is proposed for 1∅ to m∅ conversion which can extensively operate to derive the output frequency up to half of the rated supply frequency and ensures balanced operation with better power quality across the supply as well as load side. The proposed SSMC is having three branches each constitute of an array of bidirectional switches supplied by a 1∅ source through a filter circuit of one inductor and two capacitors. This configuration of the proposed SSMC make it suitable to synthesize m ∅ output from the available 1∅ power supply from very low output frequency to maximum frequency equals to half of the rated supply frequency while maintaining supply side unity power factor (UPF) and standard voltage transfer ratio (VTR). Experimental results are presented to validate the performance of the proposed SSMC for 1∅ to m∅ conversion.
- 22 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9839-9852
Modified Single-Stage Single-Phase to Multiphase Matrix Converter for Extended Low Output Power Frequency Operation
Practical applicability of the single-phase (1∅) power supplied conventional single-stage matrix converter (SSMC) to synthesize multi-phase (m∅) power is limited to very low frequency (3 to 5 Hz) output. In this paper, a modified SSMC is proposed for 1∅ to m∅ conversion which can extensively operate to derive the output frequency up to half of the rated supply frequency and ensures balanced operation with better power quality across the supply as well as load side. The proposed SSMC is having three branches each constitute of an array of bidirectional switches supplied by a 1∅ source through a filter circuit of one inductor and two capacitors. This configuration of the proposed SSMC make it suitable to synthesize m ∅ output from the available 1∅ power supply from very low output frequency to maximum frequency equals to half of the rated supply frequency while maintaining supply side unity power factor (UPF) and standard voltage transfer ratio (VTR). Experimental results are presented to validate the performance of the proposed SSMC for 1∅ to m∅ conversion.
- Open Access
- 22 December 2022
- Published by Atlantis Press SARL
- p. 132-140
Single-Phase to Six-Phase (AC-DC-AC) Converter for Traction
- 22 December 2022
- Published by Atlantis Press SARL
- p. 132-140
Open AccessSingle-Phase to Six-Phase (AC-DC-AC) Converter for Traction
- 19 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (2) , 1372-1377
Dual Stage Single-Phase to Multiphase Matrix Converter for Variable Frequency Applications
A single-stage matrix converter (MC) is preferred for the conversion of a single-phase$({1\emptyset })$ supply of fundamental frequency (50 Hz) to the multiphase$({m\emptyset })$ power supply in a limited operating frequency range (5–15 Hz). These converters possess a limitation on account of voltage and current distortions when the converter is used up to fundamental or higher frequency operating loads. To resolve this problem, this letter proposes a dual-stage$1\emptyset \ \text{to}\ m\emptyset $ MC, which ensures improved power quality across the output voltage and current. This converter has a three-leg front-end side rectifier stage (RS) consisting of six numbers of common emitter configured bidirectional power semiconductor switches. A filter circuit is installed in between$1\emptyset $ supply and RS enabling to build positive average dc voltage across the virtual dc link while maintaining the source current profile. The second stage is an inversion stage having a conventional voltage source inverter structure. The proposed dual-stage MC topology is having a simple structure with the ability to convert the$1\emptyset $ supply to any number of desired output phases not only at the lower frequency but also at the fundamental and higher frequency. The practical applicability of the proposed dual-stage MC is validated through experimental results.- 19 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (2) , 1372-1377
Dual Stage Single-Phase to Multiphase Matrix Converter for Variable Frequency Applications
A single-stage matrix converter (MC) is preferred for the conversion of a single-phase$({1\emptyset })$ supply of fundamental frequency (50 Hz) to the multiphase$({m\emptyset })$ power supply in a limited operating frequency range (5–15 Hz). These converters possess a limitation on account of voltage and current distortions when the converter is used up to fundamental or higher frequency operating loads. To resolve this problem, this letter proposes a dual-stage$1\emptyset \ \text{to}\ m\emptyset $ MC, which ensures improved power quality across the output voltage and current. This converter has a three-leg front-end side rectifier stage (RS) consisting of six numbers of common emitter configured bidirectional power semiconductor switches. A filter circuit is installed in between$1\emptyset $ supply and RS enabling to build positive average dc voltage across the virtual dc link while maintaining the source current profile. The second stage is an inversion stage having a conventional voltage source inverter structure. The proposed dual-stage MC topology is having a simple structure with the ability to convert the$1\emptyset $ supply to any number of desired output phases not only at the lower frequency but also at the fundamental and higher frequency. The practical applicability of the proposed dual-stage MC is validated through experimental results.- 12 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 4848-4858
Common-Mode Voltage Minimization in Three-Phase to Six-Phase Indirect Matrix Converter Using Virtual Vector Synthesization
This article presents the reduction in common mode voltage (CMV) in a three-phase to six-phase indirect matrix converter feeding power to a six-phase load using space vector modulation technique based on virtual vector synthesization. From the total available 64 vectors, 6 virtual vectors are derived to develop a switching algorithm giving an effective reduction in CMV for symmetrical ( 60° ) six-phase system. The voltage transformation ratio is maintained maximum possible from the presented switching algorithm. This three-phase to six-phase conversion system maintains unity power factor across the three-phase supply side, hence no reactive power is drawn from the supply. This complex control is implemented using two conjunct processors controlled in a master and slave manner. Simulation, as well as hardware, results are presented to validate the proposed control technique.
- 12 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 4848-4858
Common-Mode Voltage Minimization in Three-Phase to Six-Phase Indirect Matrix Converter Using Virtual Vector Synthesization
This article presents the reduction in common mode voltage (CMV) in a three-phase to six-phase indirect matrix converter feeding power to a six-phase load using space vector modulation technique based on virtual vector synthesization. From the total available 64 vectors, 6 virtual vectors are derived to develop a switching algorithm giving an effective reduction in CMV for symmetrical ( 60° ) six-phase system. The voltage transformation ratio is maintained maximum possible from the presented switching algorithm. This three-phase to six-phase conversion system maintains unity power factor across the three-phase supply side, hence no reactive power is drawn from the supply. This complex control is implemented using two conjunct processors controlled in a master and slave manner. Simulation, as well as hardware, results are presented to validate the proposed control technique.
- 29 July 2020
- Published by Springer Nature
- p. 132-143
Space Vector Controlled Single-Phase to Three-Phase Direct Matrix Converter Drive
- 29 July 2020
- Published by Springer Nature
- p. 132-143
Space Vector Controlled Single-Phase to Three-Phase Direct Matrix Converter Drive
- 27 May 2020
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 68 (5) , 3447-3456
Implementation of Space Vector Modulated Single-phase to Three-phase Indirect Matrix Converter for Induction Motor Drive Control
This paper presents a space vector modulated single-phase to three-phase (1 × 3) Indirect Matrix Converter (IMC). The IMC is comprised of a front-end side rectifier followed by a voltage source inverter (VSI). DC voltage appears at the intermediate of the rectifier and VSI, this virtual DC-link does not have any energy storage element (battery or capacitor), which reduces total power to weight ratio of the IMC converter, as compared to conventional AC–DC-AC converters. LC-filter is connected at the source side to reduce the harmonics present in the supply side. But the source side LC-filter disturbs the unity power factor (UPF) operation of matrix converter. In this paper, a control technique is proposed to transform single-phase quantities into stationary reference frame in order to maintain UPF at the input stage of IMC. The feasibility of control strategy for the IMC is analyzed in MATLAB/Simulink environment and a laboratory prototype is also developed supplying power to a three-phase induction motor.
- 27 May 2020
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 68 (5) , 3447-3456
Implementation of Space Vector Modulated Single-phase to Three-phase Indirect Matrix Converter for Induction Motor Drive Control
This paper presents a space vector modulated single-phase to three-phase (1 × 3) Indirect Matrix Converter (IMC). The IMC is comprised of a front-end side rectifier followed by a voltage source inverter (VSI). DC voltage appears at the intermediate of the rectifier and VSI, this virtual DC-link does not have any energy storage element (battery or capacitor), which reduces total power to weight ratio of the IMC converter, as compared to conventional AC–DC-AC converters. LC-filter is connected at the source side to reduce the harmonics present in the supply side. But the source side LC-filter disturbs the unity power factor (UPF) operation of matrix converter. In this paper, a control technique is proposed to transform single-phase quantities into stationary reference frame in order to maintain UPF at the input stage of IMC. The feasibility of control strategy for the IMC is analyzed in MATLAB/Simulink environment and a laboratory prototype is also developed supplying power to a three-phase induction motor.
- Open Access
- 1 January 2020
- Published by BioAxis DNA Research Centre in HELIX
- Vol. 10 (1) , 271-277
Comparative Study of Space Vector Controlled Three Phase-Six Phase Direct and Indirect Matrix Converter for Six Phase Induction Motor Drive
- 1 January 2020
- Published by BioAxis DNA Research Centre in HELIX
- Vol. 10 (1) , 271-277
Open AccessComparative Study of Space Vector Controlled Three Phase-Six Phase Direct and Indirect Matrix Converter for Six Phase Induction Motor Drive
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1535-1540
Grid Connected Multilevel Single to Three Phase Power Converter with Improved Performance
In this paper, single to three-phase multilevel converter topology is proposed with improved performance. A control algorithm for T-type three-level converter is proposed to balance the individual capacitor voltages and also maintain the unity power factor at the utility grid side. The voltage vectors of each sector are selected in such a way that the difference between the two capacitor voltages (V c1 and V c2 ) is about 2–5% of the total dc-link voltage and the active front end converter control strategy works effectively at the grid side, such that the grid voltage and current are in the same phase and also reduces the dc-link voltage ripples. The balancing of the individual capacitor voltages possessed a good impact on the output of the inverter in terms of reduction in voltage and current THD along with reduction in common mode voltage (voltage difference between the neutral point of the load and the mid-point of the dc-link capacitor). The effectiveness of the control technique on the active front end converter side and three-level T-type inverter side is verified using simulation results.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1535-1540
Grid Connected Multilevel Single to Three Phase Power Converter with Improved Performance
In this paper, single to three-phase multilevel converter topology is proposed with improved performance. A control algorithm for T-type three-level converter is proposed to balance the individual capacitor voltages and also maintain the unity power factor at the utility grid side. The voltage vectors of each sector are selected in such a way that the difference between the two capacitor voltages (V c1 and V c2 ) is about 2–5% of the total dc-link voltage and the active front end converter control strategy works effectively at the grid side, such that the grid voltage and current are in the same phase and also reduces the dc-link voltage ripples. The balancing of the individual capacitor voltages possessed a good impact on the output of the inverter in terms of reduction in voltage and current THD along with reduction in common mode voltage (voltage difference between the neutral point of the load and the mid-point of the dc-link capacitor). The effectiveness of the control technique on the active front end converter side and three-level T-type inverter side is verified using simulation results.