Pin-Hui Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pin-Hui Chen has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Nicholas Alaniva
Department of Chemistry and Applied Biosciences, Eidgenössische Technische Hochschule Zürich, Zürich 8049, Switzerland
4 shared publications - Alexander Däpp
Department of Chemistry and Applied Biosciences, Eidgenössische Technische Hochschule Zürich, Zürich 8049, Switzerland
3 shared publications - Chukun Gao
Department of Chemistry and Applied Biosciences, Eidgenössische Technische Hochschule Zürich, Zürich 8049, Switzerland
3 shared publications Michael Urban
Department of Chemistry and Applied Biosciences, Eidgenössische Technische Hochschule Zürich, Zürich 8049, Switzerland
3 shared publications- Alexander B. Barnes
Department of Chemistry and Applied Biosciences, ETH Zurich, Zurich, Switzerland
2 shared publications - Edward P. Saliba
Department of Chemistry and Francis Bitter Magnet Laboratory, Massachusetts Institute of Technology, Cambridge, MA 02139, United States
2 shared publications
Latest Publications
- Open Access
- 13 March 2026
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 12 (11) , eadz5826
40 Tesla miniature magnets
Ultrahigh magnetic fields enable substantial advancements across a wide range of scientific disciplines. Traditionally, steady fields above 40 tesla have been achievable only with large resistive magnets that consume megawatts of power. Here, we demonstrate peak fields of 38 and 42 tesla using two compact all-HTS magnets, composed of two and four pancake coils, respectively. These magnets achieve current densities of up to 2257 amps per square millimeter and feature an exceptionally small bore diameter of 3.1 millimeters. Furthermore, the magnet coils are small enough to fit in the palm of a hand and consume less than 1 watt of power. Such compact magnets are realized through specialized winding methods that enable seamless winding over the small diameter while preserving the current-carrying capacity of the HTS tape. Nuclear magnetic resonance (NMR) experiments were performed inside the 3-millimeter magnet bore to provide calibration points for Hall sensors. These results show the potential of compact all-HTS magnets to enable widely accessible high-field NMR and other applications.
- 13 March 2026
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 12 (11) , eadz5826
Open Access40 Tesla miniature magnets
Ultrahigh magnetic fields enable substantial advancements across a wide range of scientific disciplines. Traditionally, steady fields above 40 tesla have been achievable only with large resistive magnets that consume megawatts of power. Here, we demonstrate peak fields of 38 and 42 tesla using two compact all-HTS magnets, composed of two and four pancake coils, respectively. These magnets achieve current densities of up to 2257 amps per square millimeter and feature an exceptionally small bore diameter of 3.1 millimeters. Furthermore, the magnet coils are small enough to fit in the palm of a hand and consume less than 1 watt of power. Such compact magnets are realized through specialized winding methods that enable seamless winding over the small diameter while preserving the current-carrying capacity of the HTS tape. Nuclear magnetic resonance (NMR) experiments were performed inside the 3-millimeter magnet bore to provide calibration points for Hall sensors. These results show the potential of compact all-HTS magnets to enable widely accessible high-field NMR and other applications.
- Open Access
- 21 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (4) , 1-5
Design and Implementation of a Mechanical Semipersistent Switch for HTS Magnets
Persistent-mode operation of superconducting magnets requires a persistent switch, usually a heater, to close their superconducting circuits. Here we describe a mechanical copper switch that utilizes pressure to vary resistance. This switch is designed to provide a low resistance short between two high temperature superconductors (HTS) charging electrodes in an all-HTS pancake-coil magnet. The switch is able to achieve a contact resistance as low as 460 nΩ by pressing gold-coated copper surfaces together at 3.0 kN. At 77 K, with an HTS pancake-coil charged to 0.45 T the magnetic field decayed slowly with the switch closed. The decay fits to a 3.6 μΩ resistance, most of which arises from unrelated insufficient connections within the HTS magnet, itself. The design shows the potential of building a persistent mode superconducting magnet with a mechanical switch, where, as an example a 30 T magnet with an inductance of 5.9 Henry has a field drift of -6 ppm/h.
- 21 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (4) , 1-5
Open AccessDesign and Implementation of a Mechanical Semipersistent Switch for HTS Magnets
Persistent-mode operation of superconducting magnets requires a persistent switch, usually a heater, to close their superconducting circuits. Here we describe a mechanical copper switch that utilizes pressure to vary resistance. This switch is designed to provide a low resistance short between two high temperature superconductors (HTS) charging electrodes in an all-HTS pancake-coil magnet. The switch is able to achieve a contact resistance as low as 460 nΩ by pressing gold-coated copper surfaces together at 3.0 kN. At 77 K, with an HTS pancake-coil charged to 0.45 T the magnetic field decayed slowly with the switch closed. The decay fits to a 3.6 μΩ resistance, most of which arises from unrelated insufficient connections within the HTS magnet, itself. The design shows the potential of building a persistent mode superconducting magnet with a mechanical switch, where, as an example a 30 T magnet with an inductance of 5.9 Henry has a field drift of -6 ppm/h.
- 21 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-9
Fabrication Procedures and Mechanical Supports of No-Insulation All-GdBCO Double Pancake Magnets in Liquid Helium
The no-insulation (NI) high-temperature superconductor (HTS) winding technique enables the fabrication of highly compact magnets with self-quench protection. NI pancake coils are implemented to develop a 28-T HTS magnet for the operation of a 792-GHz gyrotron, which is a microwave source for dynamic nuclear polarization nuclear magnetic resonance. To this end, three NI all-GdBCO double pancake (DP) magnets were fabricated using different winding diameters and procedures. The objective was to explore different mechanical coil protection mechanisms at high magnetic fields, including clamping, overband, and solder impregnation. Experiments in liquid helium using magnets with winding diameters of 18, 25, and 66 mm yielded a center field of 14.4, 11.2, and 8.1 T, respectively. The maximum currents applied to the DP magnets ranged from 780 to 1000 A. Both the 18 and 66 mm DP coils contained 400 m (2 × 200 m) HTS tape, while the 25 mm seamless DP coil consisted of only one continuous 200 m HTS tape. The 25 mm magnet with solder impregnation showed the best repeatability, although the current density was reduced owing to the solder thickness between the coil windings. Critical to the implementation of such coils in liquid helium is to effectively transfer high currents to the magnet, while not compromising the helium boil-off. Furthermore, the design of hybrid copper-HTS current leads capable of carrying current larger than 1000 A from room temperature to the HTS magnet at 4.2 K is presented. The implementation of liquid nitrogen-cooled hybrid copper-HTS current leads reduced the helium boil-off and permitted independent temperature control of the current leads.
- 21 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (4) , 1-9
Fabrication Procedures and Mechanical Supports of No-Insulation All-GdBCO Double Pancake Magnets in Liquid Helium
The no-insulation (NI) high-temperature superconductor (HTS) winding technique enables the fabrication of highly compact magnets with self-quench protection. NI pancake coils are implemented to develop a 28-T HTS magnet for the operation of a 792-GHz gyrotron, which is a microwave source for dynamic nuclear polarization nuclear magnetic resonance. To this end, three NI all-GdBCO double pancake (DP) magnets were fabricated using different winding diameters and procedures. The objective was to explore different mechanical coil protection mechanisms at high magnetic fields, including clamping, overband, and solder impregnation. Experiments in liquid helium using magnets with winding diameters of 18, 25, and 66 mm yielded a center field of 14.4, 11.2, and 8.1 T, respectively. The maximum currents applied to the DP magnets ranged from 780 to 1000 A. Both the 18 and 66 mm DP coils contained 400 m (2 × 200 m) HTS tape, while the 25 mm seamless DP coil consisted of only one continuous 200 m HTS tape. The 25 mm magnet with solder impregnation showed the best repeatability, although the current density was reduced owing to the solder thickness between the coil windings. Critical to the implementation of such coils in liquid helium is to effectively transfer high currents to the magnet, while not compromising the helium boil-off. Furthermore, the design of hybrid copper-HTS current leads capable of carrying current larger than 1000 A from room temperature to the HTS magnet at 4.2 K is presented. The implementation of liquid nitrogen-cooled hybrid copper-HTS current leads reduced the helium boil-off and permitted independent temperature control of the current leads.
- Open Access
- 7 September 2018
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 4 (9) , eaau1540
Magic angle spinning spheres
Magic angle spinning (MAS) is commonly used in nuclear magnetic resonance of solids to improve spectral resolution. Rather than using cylindrical rotors for MAS, we demonstrate that spherical rotors can be spun stably at the magic angle. Spherical rotors conserve valuable space in the probe head and simplify sample exchange and microwave coupling for dynamic nuclear polarization. In this current implementation of spherical rotors, a single gas stream provides bearing gas to reduce friction, drive propulsion to generate and maintain angular momentum, and variable temperature control for thermostating. Grooves are machined directly into zirconia spheres, thereby converting the rotor body into a robust turbine with high torque. We demonstrate that 9.5–mm–outside diameter spherical rotors can be spun at frequencies up to 4.6 kHz with N2(g) and 10.6 kHz with He(g). Angular stability of the spinning axis is demonstrated by observation of 79Br rotational echoes out to 10 ms from KBr packed within spherical rotors. Spinning frequency stability of ±1 Hz is achieved with resistive heating feedback control. A sample size of 36 μl can be accommodated in 9.5-mm-diameter spheres with a cylindrical hole machined along the spinning axis. We further show that spheres can be more extensively hollowed out to accommodate 161 μl of the sample, which provides superior signal-to-noise ratio compared to traditional 3.2-mm-diameter cylindrical rotors.
- 7 September 2018
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 4 (9) , eaau1540
Open AccessMagic angle spinning spheres
Magic angle spinning (MAS) is commonly used in nuclear magnetic resonance of solids to improve spectral resolution. Rather than using cylindrical rotors for MAS, we demonstrate that spherical rotors can be spun stably at the magic angle. Spherical rotors conserve valuable space in the probe head and simplify sample exchange and microwave coupling for dynamic nuclear polarization. In this current implementation of spherical rotors, a single gas stream provides bearing gas to reduce friction, drive propulsion to generate and maintain angular momentum, and variable temperature control for thermostating. Grooves are machined directly into zirconia spheres, thereby converting the rotor body into a robust turbine with high torque. We demonstrate that 9.5–mm–outside diameter spherical rotors can be spun at frequencies up to 4.6 kHz with N2(g) and 10.6 kHz with He(g). Angular stability of the spinning axis is demonstrated by observation of 79Br rotational echoes out to 10 ms from KBr packed within spherical rotors. Spinning frequency stability of ±1 Hz is achieved with resistive heating feedback control. A sample size of 36 μl can be accommodated in 9.5-mm-diameter spheres with a cylindrical hole machined along the spinning axis. We further show that spheres can be more extensively hollowed out to accommodate 161 μl of the sample, which provides superior signal-to-noise ratio compared to traditional 3.2-mm-diameter cylindrical rotors.