Ali Torabian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ali Torabian has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Gholamreza Nabi Bidhendi
Faculty of Environment, University of Tehran, Tehran, Iran
5 shared publications - Behnoush Aminzadeh
School of Environment, College of Engineering, University of Tehran, Tehran, Iran
3 shared publications - Majid Baghdadi
University of Tehran
2 shared publications - Nasser Mehrdadi
Faculty of Environment, University of Tehran, Tehran, Iran
2 shared publications A. Azizi
Islamic Azad University
1 shared publicationA. H. Hassani
Islamic Azad University
1 shared publication
Latest Publications
- Open Access
A Comparison of the Performance of the Pre-Ozonation Process and the Use of Coagulants with Ozone in the Removal of Algae from Surface Water
Purifying surface water in moderate-humid climates is challenging due to high levels of organic compounds and diatom algae, which can produce toxic substances. A new method involving chitosan and ferric chloride coagulants, along with pre-ozonation, shows promise for improving water quality. The study examined various conditions, including pH levels and concentrations of chitosan (20–500 mg/L) and ferric chloride (5–100 mg/L), as well as the pH of reaction mixtures (3–11) and ozone concentrations (2–8 mg/L). Optimal results were achieved at a pH of 10 for both coagulants, with 500 mg/L chitosan and 75 mg/L ferric chloride. A pH of 7 for the reaction mixture and an ozone concentration of 8 mg/L were most effective. The pre-ozonation process alone can eliminate 72% of algae, while combining ozone with chitosan and ferric chloride achieved diatom removal rates of 77% and 79%, respectively. These findings highlight the effectiveness of using lower ozone concentrations in conjunction with coagulants for water purification.
Open AccessA Comparison of the Performance of the Pre-Ozonation Process and the Use of Coagulants with Ozone in the Removal of Algae from Surface Water
Purifying surface water in moderate-humid climates is challenging due to high levels of organic compounds and diatom algae, which can produce toxic substances. A new method involving chitosan and ferric chloride coagulants, along with pre-ozonation, shows promise for improving water quality. The study examined various conditions, including pH levels and concentrations of chitosan (20–500 mg/L) and ferric chloride (5–100 mg/L), as well as the pH of reaction mixtures (3–11) and ozone concentrations (2–8 mg/L). Optimal results were achieved at a pH of 10 for both coagulants, with 500 mg/L chitosan and 75 mg/L ferric chloride. A pH of 7 for the reaction mixture and an ozone concentration of 8 mg/L were most effective. The pre-ozonation process alone can eliminate 72% of algae, while combining ozone with chitosan and ferric chloride achieved diatom removal rates of 77% and 79%, respectively. These findings highlight the effectiveness of using lower ozone concentrations in conjunction with coagulants for water purification.
- 23 June 2023
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 234 (7) , 1-17
Sequential Treatment of Textile Industry Wastewater Using Electrocoagulation and Photo electro-Fenton Processes
- 23 June 2023
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 234 (7) , 1-17
Sequential Treatment of Textile Industry Wastewater Using Electrocoagulation and Photo electro-Fenton Processes
- 29 August 2019
- Published by IWA Publishing in Journal of Water Supply: Research and Technology—AQUA
- Vol. 68 (7) , 573-584
Prediction of groundwater quality parameter in the Tabriz plain, Iran using soft computing methods
Aquifers are one of the largest available freshwater resources. In this paper, total dissolved solids (TDS) of the groundwater aquifer in Tabriz plain is estimated by groundwater physicochemical parameters including Na, HCO3, Ca, Mg, and SO4 in the eastern region of Urmia Lake. For this purpose, four soft computing approaches, namely, multilayer perceptron (MLP), adaptive neuro-fuzzy inference system (ANFIS), support vector machine (SVM), and gene expression programming (GEP) were used to predict TDS for a period of ten years (2002–2012). Data were collected from the East Azerbaijan Regional Water Organization, which totaled 1,742 samples. In the application, of the whole data set, 70% (1,220 samples) was used for training and 30% (522 samples) for testing. In the following, the correlation coefficient (R), root mean square error (RMSE), and mean absolute error (MAE) statistics were used for evaluating the accuracy of the models. According to the results, MLP, ANFIS, SVM, and GEP models could be employed successfully in estimating TDS alterations. A comparison was made between these soft computing approaches that corroborated the superiority of the GEP model over MLP, SVM, and ANFIS models with RMSE = 58.93, R = 0.998, and MAE = 5.21.
- 29 August 2019
- Published by IWA Publishing in Journal of Water Supply: Research and Technology—AQUA
- Vol. 68 (7) , 573-584
Prediction of groundwater quality parameter in the Tabriz plain, Iran using soft computing methods
Aquifers are one of the largest available freshwater resources. In this paper, total dissolved solids (TDS) of the groundwater aquifer in Tabriz plain is estimated by groundwater physicochemical parameters including Na, HCO3, Ca, Mg, and SO4 in the eastern region of Urmia Lake. For this purpose, four soft computing approaches, namely, multilayer perceptron (MLP), adaptive neuro-fuzzy inference system (ANFIS), support vector machine (SVM), and gene expression programming (GEP) were used to predict TDS for a period of ten years (2002–2012). Data were collected from the East Azerbaijan Regional Water Organization, which totaled 1,742 samples. In the application, of the whole data set, 70% (1,220 samples) was used for training and 30% (522 samples) for testing. In the following, the correlation coefficient (R), root mean square error (RMSE), and mean absolute error (MAE) statistics were used for evaluating the accuracy of the models. According to the results, MLP, ANFIS, SVM, and GEP models could be employed successfully in estimating TDS alterations. A comparison was made between these soft computing approaches that corroborated the superiority of the GEP model over MLP, SVM, and ANFIS models with RMSE = 58.93, R = 0.998, and MAE = 5.21.
- Open Access
- 1 August 2019
- Published by Elsevier in Desalination and Water Treatment
- Vol. 160, 366-377
Application of lightweight expanded clay aggregate as sorbent for crude oil cleanup
- 1 August 2019
- Published by Elsevier in Desalination and Water Treatment
- Vol. 160, 366-377
Open AccessApplication of lightweight expanded clay aggregate as sorbent for crude oil cleanup
- Open Access
- 28 August 2018
- Published by Springer Nature in Biotechnology for Biofuels
- Vol. 11 (1) , 233
Improvement of anaerobic digestion of sewage mixed sludge using free nitrous acid and Fenton pre-treatment
Recently, it has been indicated that free nitrous acid (FNA) and Fenton pre-treatment of waste activated sludge can enhance methane production in anaerobic digestion of waste activated sludge. In addition, it has been revealed that the substances used in these pre-treatments are both eco-friendly and economically attractive because not only are they produced in anaerobic digestion, but they are also low priced. Since primary sludge and waste activated sludge are mixed prior to anaerobic digestion in the majority of wastewater treatment plants, this study aims to assess the influence of combined FNA and Fenton on the anaerobic digestion of mixed sludge. According to this study’s results, methane generation from anaerobic digestion of mixed sludge was enhanced when using FNA and Fenton pre-treatment, affirming the effectiveness of the individual and combined pre-treatments in anaerobic digestion of mixed sludge. The enhanced methane production was significant in combined pre-treatments (up to 72%), compared with FNA and Fenton pre-treatment alone (25% and 27%, respectively). This corroborates the positive synergistic effect of the combined pre-treatments on methane production. The enhanced methane can be attributed to augmented soluble fractions of organic matter in addition to increased readily biodegradable organic matter, caused by the pre-treatments. Additionally, the amount of chemical oxygen demand (COD) was assessed during anaerobic digestion, and it was revealed that COD decreased considerably when the pre-treatment strategies were combined. This study reveals that the pre-treatments are potentially applicable to full-scale wastewater treatment plants because a mixture of primary sludge and waste activated sludge was used for the pre-treatments. Additionally, combined FNA and Fenton pre-treatments prove more effective in enhancing methane production and organic removal than these pre-treatments alone. The enhanced methane production is important for two reasons: a higher amount of renewable energy could be generated from the enhanced methane production and the COD of digested sludge reduces in such a way that facilitates application of the sludge to agricultural lands and reduces sludge transport costs.
- 28 August 2018
- Published by Springer Nature in Biotechnology for Biofuels
- Vol. 11 (1) , 233
Open AccessImprovement of anaerobic digestion of sewage mixed sludge using free nitrous acid and Fenton pre-treatment
Recently, it has been indicated that free nitrous acid (FNA) and Fenton pre-treatment of waste activated sludge can enhance methane production in anaerobic digestion of waste activated sludge. In addition, it has been revealed that the substances used in these pre-treatments are both eco-friendly and economically attractive because not only are they produced in anaerobic digestion, but they are also low priced. Since primary sludge and waste activated sludge are mixed prior to anaerobic digestion in the majority of wastewater treatment plants, this study aims to assess the influence of combined FNA and Fenton on the anaerobic digestion of mixed sludge. According to this study’s results, methane generation from anaerobic digestion of mixed sludge was enhanced when using FNA and Fenton pre-treatment, affirming the effectiveness of the individual and combined pre-treatments in anaerobic digestion of mixed sludge. The enhanced methane production was significant in combined pre-treatments (up to 72%), compared with FNA and Fenton pre-treatment alone (25% and 27%, respectively). This corroborates the positive synergistic effect of the combined pre-treatments on methane production. The enhanced methane can be attributed to augmented soluble fractions of organic matter in addition to increased readily biodegradable organic matter, caused by the pre-treatments. Additionally, the amount of chemical oxygen demand (COD) was assessed during anaerobic digestion, and it was revealed that COD decreased considerably when the pre-treatment strategies were combined. This study reveals that the pre-treatments are potentially applicable to full-scale wastewater treatment plants because a mixture of primary sludge and waste activated sludge was used for the pre-treatments. Additionally, combined FNA and Fenton pre-treatments prove more effective in enhancing methane production and organic removal than these pre-treatments alone. The enhanced methane production is important for two reasons: a higher amount of renewable energy could be generated from the enhanced methane production and the COD of digested sludge reduces in such a way that facilitates application of the sludge to agricultural lands and reduces sludge transport costs.
- Open Access
- 1 March 2018
- Published by Elsevier in Desalination and Water Treatment
- Vol. 109, 139-144
Removal of lindane as a health-toxic pesticide in drinking water by slow sand filtration
- 1 March 2018
- Published by Elsevier in Desalination and Water Treatment
- Vol. 109, 139-144
Open AccessRemoval of lindane as a health-toxic pesticide in drinking water by slow sand filtration
- 26 September 2017
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 15 (12) , 2669-2678
Investigating the removal of ethylbenzene from aqueous solutions using modified graphene oxide: application of response surface methodology
- 26 September 2017
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 15 (12) , 2669-2678
Investigating the removal of ethylbenzene from aqueous solutions using modified graphene oxide: application of response surface methodology
- Open Access
- 20 June 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (59) , 28806-28821
Adsorption performance of modified graphene oxide nanoparticles for the removal of toluene, ethylbenzene, and xylenes from aqueous solution
The purpose of this study was to investigate the effect of graphene oxide nanoparticles modified with 4-aminodiphenylamine (GO-A) on the removal of toluene, ethylbenzene, and p-,o-xylene (TEX). Nano-sorbent was characterized using Fourier transform infrared resonance spectroscopy, carbon, hydrogen and nitrogen elemental analysis, Brunauer-Emmett-Teller analysis, and transmission electron microscopy. The effect of different experimental parameters including contact time, pH, and initial concentration of adsorbate and adsorbent were examined. According to the results, an optimum TEX removal efficiency was observed at contact time = 5 min, pH 4, and adsorbent dose = 1 g/L at 20 mg/L initial TEX concentration. Besides, the point of zero charge (pHpzc) was evaluated to be 4. The adsorption isotherms (Langmuir, Freundlich, and Dubinin–RadushKevich) and kinetics (pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich) were used to indicate the isotherm and kinetic parameters. The adsorption process followed Langmuir isotherm and pseudo-second-order kinetic. Finally, GO-A was regenerated at seven cycles for the TEX removal confirming its good regeneration capacity.
- 20 June 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (59) , 28806-28821
Open AccessAdsorption performance of modified graphene oxide nanoparticles for the removal of toluene, ethylbenzene, and xylenes from aqueous solution
The purpose of this study was to investigate the effect of graphene oxide nanoparticles modified with 4-aminodiphenylamine (GO-A) on the removal of toluene, ethylbenzene, and p-,o-xylene (TEX). Nano-sorbent was characterized using Fourier transform infrared resonance spectroscopy, carbon, hydrogen and nitrogen elemental analysis, Brunauer-Emmett-Teller analysis, and transmission electron microscopy. The effect of different experimental parameters including contact time, pH, and initial concentration of adsorbate and adsorbent were examined. According to the results, an optimum TEX removal efficiency was observed at contact time = 5 min, pH 4, and adsorbent dose = 1 g/L at 20 mg/L initial TEX concentration. Besides, the point of zero charge (pHpzc) was evaluated to be 4. The adsorption isotherms (Langmuir, Freundlich, and Dubinin–RadushKevich) and kinetics (pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich) were used to indicate the isotherm and kinetic parameters. The adsorption process followed Langmuir isotherm and pseudo-second-order kinetic. Finally, GO-A was regenerated at seven cycles for the TEX removal confirming its good regeneration capacity.
- Open Access
- 17 February 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (52) , 24855-24866
Preparation of engineered carbon nanotube materials and its application in water treatment for removal of hydrophobic natural organic matter (NOM)
Organic matters in drinking water are composed of soluble and particulate fractions. Soluble organic matters generally originated from allochthonous, autochthonous, and synthetic organic. Silica sand filters, which are utilized in water treatment, have a low potential of removing the soluble organic matters. Traditional carbon-based media such as activated carbon and anthracite are among the choices for the removal of soluble organic. Carbon nanotubes (CNTs) have a higher potential in removing synthetic and natural organic materials than the other traditional carbon based media. Utilization of CNTs at the slurry state requires the removal of the nanotubes themselves at the end of the process which leads to yet another problem to take care of. The present study, therefore, aims at solving this problem. In so doing, oxidized CNTs (140°C, 5 h, Nitric acid) were bound to the surface of silica sand through 3-(triethoxysilyl)propylamine to act as a bonding agent. Humic acid was used as the index of natural organic matters. The removal potential of humic acid with the new adsorbent (CNTsand) was studied under various operational conditions (contact time, temperature, and initial concentration). According to the obtained data, CNTsand has a good potential in the removal of humic acid (qmax = 81.96 mg/g CNT). Additionally, the kinetic, isotherm, and thermodynamic of adsorption were investigated, for which the data followed the pseudo-second-order kinetic model and Langmuir isotherm. Evaluation of enthalpy change (ΔH = 11.02 kJ/mol) and free energy change (ΔG = –7.32 to –9.20 kJ/mol) indicated that the reaction is spontaneous, endothermic, and thermodynamically favorable. Regeneration study showed that the desorption step of humic acid was faster than its adsorption step. It was observed that after five cycles, the adsorption capacity amounted to roughly 50% of the initial adsorption capacity. The above data depict that the new engineered material is a good reusable adsorbent in water treatment.
- 17 February 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (52) , 24855-24866
Open AccessPreparation of engineered carbon nanotube materials and its application in water treatment for removal of hydrophobic natural organic matter (NOM)
Organic matters in drinking water are composed of soluble and particulate fractions. Soluble organic matters generally originated from allochthonous, autochthonous, and synthetic organic. Silica sand filters, which are utilized in water treatment, have a low potential of removing the soluble organic matters. Traditional carbon-based media such as activated carbon and anthracite are among the choices for the removal of soluble organic. Carbon nanotubes (CNTs) have a higher potential in removing synthetic and natural organic materials than the other traditional carbon based media. Utilization of CNTs at the slurry state requires the removal of the nanotubes themselves at the end of the process which leads to yet another problem to take care of. The present study, therefore, aims at solving this problem. In so doing, oxidized CNTs (140°C, 5 h, Nitric acid) were bound to the surface of silica sand through 3-(triethoxysilyl)propylamine to act as a bonding agent. Humic acid was used as the index of natural organic matters. The removal potential of humic acid with the new adsorbent (CNTsand) was studied under various operational conditions (contact time, temperature, and initial concentration). According to the obtained data, CNTsand has a good potential in the removal of humic acid (qmax = 81.96 mg/g CNT). Additionally, the kinetic, isotherm, and thermodynamic of adsorption were investigated, for which the data followed the pseudo-second-order kinetic model and Langmuir isotherm. Evaluation of enthalpy change (ΔH = 11.02 kJ/mol) and free energy change (ΔG = –7.32 to –9.20 kJ/mol) indicated that the reaction is spontaneous, endothermic, and thermodynamically favorable. Regeneration study showed that the desorption step of humic acid was faster than its adsorption step. It was observed that after five cycles, the adsorption capacity amounted to roughly 50% of the initial adsorption capacity. The above data depict that the new engineered material is a good reusable adsorbent in water treatment.
- Open Access
- 1 May 2014
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 18 (4) , 949-955
Removal of chromium (III) from wastewater by electrocoagulation method
- 1 May 2014
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 18 (4) , 949-955
Open AccessRemoval of chromium (III) from wastewater by electrocoagulation method