Bruno Gonçalves da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bruno Gonçalves da Silva has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Nunes da Silva
Instituto Federal de Educação Ciência e Tecnologia do Rio Grande do Norte, Brasil
2 shared publications - José Yvan Pereira Leite
Instituto Federal do Rio Grande do Norte
2 shared publications - José Carlos Silva Oliveira
Universidade Federal de Pernambuco, Brasil
1 shared publication - José Rodolpho Marinho Texeira
Laboratório de Tecnologia Mineral - IFRN
1 shared publication - Leandro Araujo Freire
Universidade Federal de Pernambuco, Brasil
1 shared publication
Latest Publications
- Open Access
- 1 March 2019
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 72 (1) , 147-152
Behavior of the chromite tailings in a centrifugal concentrator (FALCON)
The application of the centrifugal concentration gains importance in the world scenario, considering the low environmental impact and the concentration of fine particles. Literature does not present articles using centrifugal concentration (Falcon) for chromite. The material used in the tests is the tailings from a Northeastern Brazil concentration plant, which was homogenized in the laboratory. In the process assays, the number of G (25-300 G) and the fluidization water pressure (20-100 kPa) were optimized. The initial tests used a wide range of particle size of 1 kg mass, with the "best results" being for 50 and 100 G at a pressure of 60 and 80 kPa, respectively, where a metallurgical recovery of 25% and grade close to 20% of Cr2O3 were obtained. The amount of mass showed to be a significant variable in the process, being 250 g the ideal for the material used, which obtained considerable recoveries, even though the grade is still low. These results led to a cut at 250 µm, considering that the liberation of the chromite is of the order of 77 %. The best result was with 150 G and fluidization water pressure of 60 kPa for a metallurgical recovery of 72% and a grade of 28% Cr2O3.
- 1 March 2019
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 72 (1) , 147-152
Open AccessBehavior of the chromite tailings in a centrifugal concentrator (FALCON)
The application of the centrifugal concentration gains importance in the world scenario, considering the low environmental impact and the concentration of fine particles. Literature does not present articles using centrifugal concentration (Falcon) for chromite. The material used in the tests is the tailings from a Northeastern Brazil concentration plant, which was homogenized in the laboratory. In the process assays, the number of G (25-300 G) and the fluidization water pressure (20-100 kPa) were optimized. The initial tests used a wide range of particle size of 1 kg mass, with the "best results" being for 50 and 100 G at a pressure of 60 and 80 kPa, respectively, where a metallurgical recovery of 25% and grade close to 20% of Cr2O3 were obtained. The amount of mass showed to be a significant variable in the process, being 250 g the ideal for the material used, which obtained considerable recoveries, even though the grade is still low. These results led to a cut at 250 µm, considering that the liberation of the chromite is of the order of 77 %. The best result was with 150 G and fluidization water pressure of 60 kPa for a metallurgical recovery of 72% and a grade of 28% Cr2O3.
- Open Access
- 5 December 2017
- Published by Instituto Federal de Educacao, Ciencia e Tecnologia do Rio Grande do Norte (IFRN) in HOLOS
- Vol. 6, 241-248
CONTROLE DE PROCESSO EM LABORATÓRIO DE PROCESSAMENTO MINERAL
O controle de processo tem grande importância nas plantas de tratamento de minérios. A instrumentação utilizada é incipiente na maior parte das usinas. Isto se deve provavelmente à ausência deste conteúdo no currículo dos cursos técnicos e de graduação na área mineral. Este trabalho tem como objetivo apresentar a inclusão do controle de processo utilizando inversores de frequência e a plataforma Arduino, tendo em vista a automação de processo em equipamentos de laboratório de processamento mineral. O uso do inversor de frequência permitiu efetuar controle de processos, tais como: taxa de alimentação, vazão, pressão, força G, frequências, entre outros.
- 5 December 2017
- Published by Instituto Federal de Educacao, Ciencia e Tecnologia do Rio Grande do Norte (IFRN) in HOLOS
- Vol. 6, 241-248
Open AccessCONTROLE DE PROCESSO EM LABORATÓRIO DE PROCESSAMENTO MINERAL
O controle de processo tem grande importância nas plantas de tratamento de minérios. A instrumentação utilizada é incipiente na maior parte das usinas. Isto se deve provavelmente à ausência deste conteúdo no currículo dos cursos técnicos e de graduação na área mineral. Este trabalho tem como objetivo apresentar a inclusão do controle de processo utilizando inversores de frequência e a plataforma Arduino, tendo em vista a automação de processo em equipamentos de laboratório de processamento mineral. O uso do inversor de frequência permitiu efetuar controle de processos, tais como: taxa de alimentação, vazão, pressão, força G, frequências, entre outros.