Zelin Han

The development of FeCrAl alloys has commenced for use as nuclear fuel cladding material, intended to serve as an enhanced accident-tolerant alternative to Zr-based alloys. In this study, the Fe-13Cr-4Al alloy, specifically designed for advanced accident-tolerant fuel (ATF) cladding, was carefully prepared through vacuum induction melting and hot-working processes. Mechanical properties and serrated flow behavior of this alloy were investigated through tensile tests at temperatures ranging from 200 to 800 °C. Intriguingly, serrations emerged within a specific temperature range, accompanied by unique mechanical behavior characteristics indicative of dynamic strain aging (DSA). Additionally, the alloy’s fracture modes showed a transition from a mix of ductile and cleavage fracture features to fully ductile fracture as the temperature increased. This study offers insights into the mechanical properties and serration behaviors of FeCrAl alloys, highlighting their potential for use in nuclear fuel cladding.

The 2.25Cr1Mo0.25V steel is a vanadium-modified 2.25Cr1Mo steel and is being widely used in the manufacture of heavy-wall hydrogenation reactors in petrochemical plants. However, the harsh service environment requires a thorough understanding of high-temperature tensile and creep behaviors of 2.25Cr1Mo0.25V steel and its weld for ensuring the safety and reliability of hydrogenation reactors. In this work, the high-temperature tensile and creep behaviors of base metal (BM) and weld metal (WM) in a 2.25Cr1Mo0.25V steel weldment used for a hydrogenation reactor were studied experimentally, paying special attention to its service temperature range of 350–500 °C. The uniaxial tensile tests under different temperatures show that the WM has higher strength and lower ductility than those of BM, due to the finer grain size in the WM. At the same time, the short-term creep tests at 550 °C reveal that the WM has a higher creep resistance than that of BM. Moreover, the creep damage mechanisms were clarified by observing the fracture surface and microstructures of crept specimens with the aid of scanning electron microscopy (SEM). The results showed that the creep damage mechanisms of both BM and WM are the initiation and growth of creep cavities at the second phase particles. Results from this work indicate that the mismatch in the high-temperature tensile strength, ductility, and creep deformation rate in 2.25Cr1Mo0.25V steel weldment needs to be considered for the design and integrity assessment of hydrogenation reactors.

The precise identification of micro-features on 2.25Cr1Mo0.25V steel is of great significance for understanding the mechanism of hydrogen embrittlement (HE) and evaluating the alloy’s properties of HE resistance. Presently, the convolution neural network (CNN) of deep learning is widely applied in the micro-features identification of alloy. However, with the development of the transformer in image recognition, the transformer-based neural network performs better on the learning of global and long-range semantic information than CNN and achieves higher prediction accuracy. In this work, a new transformer-based neural network model Swin–UNet++ was proposed. Specifically, the architecture of the decoder was redesigned to more precisely detect and identify the micro-feature with complex morphology (i.e., dimples) of 2.25Cr1Mo0.25V steel fracture surface. Swin–UNet++ and other segmentation models performed state-of-the-art (SOTA) were compared on the dimple dataset constructed in this work, which consists of 830 dimple scanning electron microscopy (SEM) images on 2.25Cr1Mo0.25V steel fracture surface. The segmentation results show Swin–UNet++ not only realizes the accurate identification of dimples but displays a much higher prediction accuracy and stronger robustness than Swin–Unet and UNet. Moreover, efforts from this work will also provide an important reference value to the identification of other micro-features with complex morphologies.

In this work, the fatigue crack growth (FCG) behavior and fatigue damage mechanism of the 2.25Cr1Mo0.25V steel welded joint used in hydrogenation reactors were investigated. The multi-pass welding was carried out to manufacture the welded joint using the combined shielded metal arc welding (SMAW) and submerged automatic arc welding (SAAW) processes. The FCG behavior of different zones in the welded joint, including the base metal (BM), the heat-affected zone (HAZ) and the weld metal (WM), were studied by compact tension tests. Moreover, the acoustic emission (AE) technique was used to monitor AE signals generated from FCG process for further understanding FCG behavior and fatigue mechanisms. Additionally, the microstructures and fracture surfaces of different specimens were observed by optical microscopy (OM) and scanning electron microscopy (SEM). The results revealed that the microstructure of BM is fine granular bainite, while the WM shows coarser bainite grains. The HAZ exhibits the most significant inhomogeneity with large dispersion of grain size. FCG results showed that the HAZ exhibits much higher fatigue crack growth rate (FCGR) at low ΔK values, while the BM shows the most superior fatigue resistance. The AE technique is successful in monitoring and identifying damage evolutions during the FCG process. Moreover, an enhanced AE activity is observed in FCG of the WM specimen, which is attributed to the combined influence of the formation of numerous secondary cracks and coarse-grained microstructures.

Fracture failure caused by hydrogen embrittlement (HE) is a major concern for the system reliability and safety of hydrogen storage vessels, which are generally made of 2.25Cr1Mo0.25V steel. Thus, study of the influence of pre-charged hydrogen on fracture toughness of as-received 2.25Cr1Mo0.25V steel and weld is of significant importance. In the current work, the influence of hydrogen on fracture toughness of as-received 2.25Cr1Mo0.25V steel and weld was systematically studied. Base metal (BM) and weld metal (WM) specimens under both hydrogen-free and hydrogen-charged conditions were tested using three-point bending tests. Hydrogen was pre-charged inside specimens by the immersion charging method. The J-integral values were calculated for quantitatively evaluating the fracture toughness. In order to investigate the HE mechanisms, optical microscopy (OM) and scanning electron microscopy (SEM) were used to characterize the microstructure of BM and WM specimens. The results revealed that the presence of pre-charged hydrogen caused a significant decrease of the fracture toughness for both BM and WM specimens. Moreover, the pre-charged hydrogen led to a remarkable transition of fracture mode from ductile to brittle pattern in 2.25Cr1Mo0.25V steel.

Hydrogen embrittlement (HE) is a critical issue that affects the reliability of hydrogenation reactors. The hydrogen diffusivity/trap characteristics of 2.25Cr-1Mo-0.25V steel are important parameters mainly used to study the HE mechanism of steel alloys. In this work, the hydrogen diffusivity/trap characteristics of heat-treated (annealed) and untreated 2.25Cr-1Mo-0.25V steel were studied using an electrochemical permeation method. The microstructures of both 2.25Cr-1Mo-0.25V steels were investigated by metallurgical microscopy. The effect of cementite on the hydrogen diffusivity/trap mechanisms was studied using thermodynamics-based and Lennard–Jones potential theories. The results revealed that the cementite located at the grain boundaries and at the interfaces of lath ferrite served as a kind of hydrogen trap (i.e., an irreversible hydrogen trap). In addition, hydrogen was transported from ferrite to cementite via up-hill diffusion, thereby supporting the hypothesis of cementite acting as a hydrogen trap.