Liberty Lungisani Mguni
Liberty Lungisani Mguni has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Xinying Liu
University of South Africa (UNISA)
5 shared publications - Yali Yao
School of Chemical and Metallurgical Engineering, University of the Witwatersrand, Johannesburg, South Africa
4 shared publications Diane Hildebrandt
Institute for the Development of Energy for African Sustainability (IDEAS), Florida Campus, University of South Africa, Johannesburg, Gauteng 1710, South Africa
2 shared publications- Diane Hildebrandt
University of Adelaide, Adelaide, Australia
2 shared publications Mbala Mukenga
2 shared publications- Reinout Meijboom
University of Johannesburg
2 shared publications
Latest Publications
- 7 February 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (7) , 3018-3029
Effect of Support Particle Size in Fischer–Tropsch Synthesis: the Use of Natural Clinoptilolite as Support
- 7 February 2024
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 63 (7) , 3018-3029
Effect of Support Particle Size in Fischer–Tropsch Synthesis: the Use of Natural Clinoptilolite as Support
- 30 March 2022
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 36 (8) , 4427-4438
Insight into Adsorptive Desulfurization by Zeolites: A Machine Learning Exploration
- 30 March 2022
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 36 (8) , 4427-4438
Insight into Adsorptive Desulfurization by Zeolites: A Machine Learning Exploration
- 23 July 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 60 (30) , 10997-11008
Modulated Synthesis of a Novel Nickel-Based Metal–Organic Framework Composite Material for the Adsorptive Desulfurization of Liquid Fuels
- 23 July 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 60 (30) , 10997-11008
Modulated Synthesis of a Novel Nickel-Based Metal–Organic Framework Composite Material for the Adsorptive Desulfurization of Liquid Fuels
- 1 April 2019
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 7 (2)
Ultra-deep desulphurization of both model and commercial diesel fuels by adsorption method
- 1 April 2019
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 7 (2)
Ultra-deep desulphurization of both model and commercial diesel fuels by adsorption method
- 10 September 2018
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 206 (5) , 572-580
Desulphurization of diesel fuels using intermediate Lewis acids loaded on activated charcoal and alumina
According to Pearson’s hard/soft (Lewis) acids/bases concept, sulfur compounds in diesel will prefer to interact with intermediate or soft Lewis acid sites since they are soft to intermediate bases. In this work, intermediate Lewis metal oxides (MO) acids were loaded on activated carbon (AC) and alumina (Al2O3) to desulfurize diesel using adsorption. For carbon-loaded MO, NiO showed the highest desulfurization activity of 89% and 50% when using both model diesel and conventional diesel, respectively. The activity of Al2O3 and Al2O3 supported MO was approximately four times less than that of AC for model diesel desulphurization. It is suggested that the low activity of Al2O3 is due to lower surface area, pore distribution, and the strong acidity nature of Al2O3 since the adsorbates are soft to intermediate Lewis bases. Lower activity, 2–4 times, was observed when treating conventional diesel compared to model diesel. This lower activity is due to competitive adsorption with compounds such as naphthalene and indole. Despite this difference, the activity trends were generally maintained suggesting that the use of model diesel is not a bad technique for screening adsorbents. Selectivity on AC was observed to decrease in this order: 4-MDBT > 1,4,6-TMDBT > 4,6-DMDBTZ ∼ 4E,6-MDBT ∼ 2,4,6-TMDBT. This suggests that steric hindrances dominate selectivity for these high-molecular weight molecules. Finally, it was observed that the challenge with regeneration of adsorbent (AC) that treated conventional diesel using solvent extraction is competitive desorption of hydrocarbons and sulfur compounds.
- 10 September 2018
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 206 (5) , 572-580
Desulphurization of diesel fuels using intermediate Lewis acids loaded on activated charcoal and alumina
According to Pearson’s hard/soft (Lewis) acids/bases concept, sulfur compounds in diesel will prefer to interact with intermediate or soft Lewis acid sites since they are soft to intermediate bases. In this work, intermediate Lewis metal oxides (MO) acids were loaded on activated carbon (AC) and alumina (Al2O3) to desulfurize diesel using adsorption. For carbon-loaded MO, NiO showed the highest desulfurization activity of 89% and 50% when using both model diesel and conventional diesel, respectively. The activity of Al2O3 and Al2O3 supported MO was approximately four times less than that of AC for model diesel desulphurization. It is suggested that the low activity of Al2O3 is due to lower surface area, pore distribution, and the strong acidity nature of Al2O3 since the adsorbates are soft to intermediate Lewis bases. Lower activity, 2–4 times, was observed when treating conventional diesel compared to model diesel. This lower activity is due to competitive adsorption with compounds such as naphthalene and indole. Despite this difference, the activity trends were generally maintained suggesting that the use of model diesel is not a bad technique for screening adsorbents. Selectivity on AC was observed to decrease in this order: 4-MDBT > 1,4,6-TMDBT > 4,6-DMDBTZ ∼ 4E,6-MDBT ∼ 2,4,6-TMDBT. This suggests that steric hindrances dominate selectivity for these high-molecular weight molecules. Finally, it was observed that the challenge with regeneration of adsorbent (AC) that treated conventional diesel using solvent extraction is competitive desorption of hydrocarbons and sulfur compounds.
- 9 February 2018
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (5) , 501-509
Effect of moisture content on oil extraction from spent coffee grounds
Spent coffee grounds (SCG) were used in this study for oil extraction. It was observed that oil extraction increased with water content up to 20 wt% for non-polar solvents and up to 40 wt% for polar solvents. At 80 wt% moisture, no oil was observed instead a black gel was formed. Oil extraction was observed to increase with time but it was concluded that increasing extraction time beyond 60 min had no significant benefit for both solvents (ethanol and toluene). The highest amount of oil extracted was observed when using ethanol at 40 wt% moisture and it was around 20%. The saponification values for oil extracted from SCG were observed to be between 175 and 180 but were lower than those obtained for soybean (193). The SCG oil was observed to contain the following fatty acids in this quantity order: palmitic> linoleic acid > stearic acid.
- 9 February 2018
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (5) , 501-509
Effect of moisture content on oil extraction from spent coffee grounds
Spent coffee grounds (SCG) were used in this study for oil extraction. It was observed that oil extraction increased with water content up to 20 wt% for non-polar solvents and up to 40 wt% for polar solvents. At 80 wt% moisture, no oil was observed instead a black gel was formed. Oil extraction was observed to increase with time but it was concluded that increasing extraction time beyond 60 min had no significant benefit for both solvents (ethanol and toluene). The highest amount of oil extracted was observed when using ethanol at 40 wt% moisture and it was around 20%. The saponification values for oil extracted from SCG were observed to be between 175 and 180 but were lower than those obtained for soybean (193). The SCG oil was observed to contain the following fatty acids in this quantity order: palmitic> linoleic acid > stearic acid.
- 1 April 2013
- Published by Elsevier in Catalysis Communications
- Vol. 34, 52-57
Effect of calcination temperature and MgO crystallite size on MgO/TiO2 catalyst system for soybean oil transesterification
- 1 April 2013
- Published by Elsevier in Catalysis Communications
- Vol. 34, 52-57
Effect of calcination temperature and MgO crystallite size on MgO/TiO2 catalyst system for soybean oil transesterification
- 5 February 2013
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 66 (1) , 91-99
Expanding the synthesis of Stöber spheres: towards the synthesis of nano-magnesium oxide and nano-zinc oxide
- 5 February 2013
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 66 (1) , 91-99
Expanding the synthesis of Stöber spheres: towards the synthesis of nano-magnesium oxide and nano-zinc oxide