Bin Tang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bin Tang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Hui Wan
The Institute of Technological Sciences, Wuhan University, Wuhan 430072, China
4 shared publications - Shengjun Zhou
Center for Photonics and Semiconductors, School of Power and Mechanical Engineering, Wuhan University, Wuhan, China
4 shared publications - Chengqun Gui
The Institute of Technological Sciences, Wuhan University, Wuhan 430072, China
3 shared publications - Ning Li
Center for Photonics and Semiconductors, Hubei Key Laboratory of Waterjet Theory and New Technology, School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072, China
2 shared publications - Yingce Liu
Xiamen Changelight Co., Ltd., Xiamen 361000, China
2 shared publications - Jia Miao
Key Laboratory of Hydraulic Machinery Transients (Wuhan University), Ministry of Education, Wuhan 430072, China
1 shared publication
Latest Publications
- Open Access
Optical Characterization of GaN-Based Vertical Blue Light-Emitting Diodes on P-Type Silicon Substrate
Fabricating GaN-based light-emitting diodes (LEDs) on a silicon (Si) substrate, which is compatible with the widely employed complementary metal–oxide–semiconductor (CMOS) circuits, is extremely important for next-generation high-performance electroluminescence devices. We conducted a systematic investigation of the optical properties of vertical LEDs, to reveal the impacts of the manufacturing process on their optical characteristics. Here, we fabricated and characterized high-efficiency GaN-based LEDs with integrated surface textures including micro-scale periodic hemispherical dimples and nano-scale random hexagonal pyramids on a 4 inch p-type Si substrate. The highly reflective Ag/TiW metallization scheme was performed to decrease downward-absorbing light. We demonstrated the influence of transferring LED epilayers from a sapphire substrate onto the Si substrate on the emission characteristics of the vertical LEDs. The removal of the sapphire substrate reduced the adverse impacts of the quantum-confined Stark effect (QCSE). The influence of integrated surface textures on the light extraction efficiency (LEE) of the vertical LEDs was studied. With the injection current of 350 mA, vertical LEDs with integrated surface textures demonstrated an excellent light output power of 468.9 mW with an emission peak wavelength of 456 nm. This work contributes to the integration of GaN-based vertical LEDs into Si-based integrated circuits.
Open AccessOptical Characterization of GaN-Based Vertical Blue Light-Emitting Diodes on P-Type Silicon Substrate
Fabricating GaN-based light-emitting diodes (LEDs) on a silicon (Si) substrate, which is compatible with the widely employed complementary metal–oxide–semiconductor (CMOS) circuits, is extremely important for next-generation high-performance electroluminescence devices. We conducted a systematic investigation of the optical properties of vertical LEDs, to reveal the impacts of the manufacturing process on their optical characteristics. Here, we fabricated and characterized high-efficiency GaN-based LEDs with integrated surface textures including micro-scale periodic hemispherical dimples and nano-scale random hexagonal pyramids on a 4 inch p-type Si substrate. The highly reflective Ag/TiW metallization scheme was performed to decrease downward-absorbing light. We demonstrated the influence of transferring LED epilayers from a sapphire substrate onto the Si substrate on the emission characteristics of the vertical LEDs. The removal of the sapphire substrate reduced the adverse impacts of the quantum-confined Stark effect (QCSE). The influence of integrated surface textures on the light extraction efficiency (LEE) of the vertical LEDs was studied. With the injection current of 350 mA, vertical LEDs with integrated surface textures demonstrated an excellent light output power of 468.9 mW with an emission peak wavelength of 456 nm. This work contributes to the integration of GaN-based vertical LEDs into Si-based integrated circuits.
- Open Access
- 17 August 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (8) , 1178
High-Power GaN-Based Vertical Light-Emitting Diodes on 4-Inch Silicon Substrate
We demonstrate high-power GaN-based vertical light-emitting diodes (LEDs) (VLEDs) on a 4-inch silicon substrate and flip-chip LEDs on a sapphire substrate. The GaN-based VLEDs were transferred onto the silicon substrate by using the Au–In eutectic bonding technique in combination with the laser lift-off (LLO) process. The silicon substrate with high thermal conductivity can provide a satisfactory path for heat dissipation of VLEDs. The nitrogen polar n-GaN surface was textured by KOH solution, which not only improved light extract efficiency (LEE) but also broke down Fabry–Pérot interference in VLEDs. As a result, a near Lambertian emission pattern was obtained in a VLED. To improve current spreading, the ring-shaped n-electrode was uniformly distributed over the entire VLED. Our combined numerical and experimental results revealed that the VLED exhibited superior heat dissipation and current spreading performance over a flip-chip LED (FCLED). As a result, under 350 mA injection current, the forward voltage of the VLED was 0.36 V lower than that of the FCLED, while the light output power (LOP) of the VLED was 3.7% higher than that of the FCLED. The LOP of the FCLED saturated at 1280 mA, but the light output saturation did not appear in the VLED.
- 17 August 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (8) , 1178
Open AccessHigh-Power GaN-Based Vertical Light-Emitting Diodes on 4-Inch Silicon Substrate
We demonstrate high-power GaN-based vertical light-emitting diodes (LEDs) (VLEDs) on a 4-inch silicon substrate and flip-chip LEDs on a sapphire substrate. The GaN-based VLEDs were transferred onto the silicon substrate by using the Au–In eutectic bonding technique in combination with the laser lift-off (LLO) process. The silicon substrate with high thermal conductivity can provide a satisfactory path for heat dissipation of VLEDs. The nitrogen polar n-GaN surface was textured by KOH solution, which not only improved light extract efficiency (LEE) but also broke down Fabry–Pérot interference in VLEDs. As a result, a near Lambertian emission pattern was obtained in a VLED. To improve current spreading, the ring-shaped n-electrode was uniformly distributed over the entire VLED. Our combined numerical and experimental results revealed that the VLED exhibited superior heat dissipation and current spreading performance over a flip-chip LED (FCLED). As a result, under 350 mA injection current, the forward voltage of the VLED was 0.36 V lower than that of the FCLED, while the light output power (LOP) of the VLED was 3.7% higher than that of the FCLED. The LOP of the FCLED saturated at 1280 mA, but the light output saturation did not appear in the VLED.
- Open Access
- 5 March 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (3) , 365
Revealing the Role of Sidewall Orientation in Wet Chemical Etching of GaN-Based Ultraviolet Light-Emitting Diodes
We demonstrated that the tetramethylammonium hydroxide (TMAH) solution possesses different etching abilities to the chip sidewalls with different orientations because the orientation of chip sidewall determines the exposed crystallographic plane of gallium nitride (GaN) and these crystallographic planes are with different chemical stability to the TMAH solution. After TMAH etching treatment, trigonal prisms were observed on sidewalls where m-plane GaN was exposed. For the investigated two types of light-emitting diodes (LEDs) with orthogonal arrangements, the LEDs with their larger sidewalls orientated along the [11–20] direction exhibited an additional 10% improvement in light output power after TMAH etching treatment compared to the LEDs with larger sidewalls orientated along the [1–100] direction.
- 5 March 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (3) , 365
Open AccessRevealing the Role of Sidewall Orientation in Wet Chemical Etching of GaN-Based Ultraviolet Light-Emitting Diodes
We demonstrated that the tetramethylammonium hydroxide (TMAH) solution possesses different etching abilities to the chip sidewalls with different orientations because the orientation of chip sidewall determines the exposed crystallographic plane of gallium nitride (GaN) and these crystallographic planes are with different chemical stability to the TMAH solution. After TMAH etching treatment, trigonal prisms were observed on sidewalls where m-plane GaN was exposed. For the investigated two types of light-emitting diodes (LEDs) with orthogonal arrangements, the LEDs with their larger sidewalls orientated along the [11–20] direction exhibited an additional 10% improvement in light output power after TMAH etching treatment compared to the LEDs with larger sidewalls orientated along the [1–100] direction.
- Open Access
- 28 February 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (3) , 319
Enhanced Light Extraction of Flip-Chip Mini-LEDs with Prism-Structured Sidewall
Current solutions for improving the light extraction efficiency of flip-chip light-emitting diodes (LEDs) mainly focus on relieving the total internal reflection at sapphire/air interface, but such methods hardly affect the epilayer mode photons. We demonstrated that the prism-structured sidewall based on tetramethylammonium hydroxide (TMAH) etching is a cost-effective solution for promoting light extraction efficiency of flip-chip mini-LEDs. The anisotropic TMAH etching created hierarchical prism structure on sidewall of mini-LEDs for coupling out photons into air without deteriorating the electrical property. Prism-structured sidewall effectively improved light output power of mini-LEDs by 10.3%, owing to the scattering out of waveguided light trapped in the gallium nitride (GaN) epilayer.
- 28 February 2019
- Published by MDPI AG in Nanomaterials
- Vol. 9 (3) , 319
Open AccessEnhanced Light Extraction of Flip-Chip Mini-LEDs with Prism-Structured Sidewall
Current solutions for improving the light extraction efficiency of flip-chip light-emitting diodes (LEDs) mainly focus on relieving the total internal reflection at sapphire/air interface, but such methods hardly affect the epilayer mode photons. We demonstrated that the prism-structured sidewall based on tetramethylammonium hydroxide (TMAH) etching is a cost-effective solution for promoting light extraction efficiency of flip-chip mini-LEDs. The anisotropic TMAH etching created hierarchical prism structure on sidewall of mini-LEDs for coupling out photons into air without deteriorating the electrical property. Prism-structured sidewall effectively improved light output power of mini-LEDs by 10.3%, owing to the scattering out of waveguided light trapped in the gallium nitride (GaN) epilayer.