Alireza Vahidi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Alireza Vahidi has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Albano Cavaleiro
2 shared publications- Albano Cavaleiro
University of Coimbra, CEMMPRE, ARISE, Department of Mechanical Engineering, Rua Luís Reis Santos, 3030-788 Coimbra, Portugal
2 shared publications Fabio Ferreira
Department of Mechanical Engineering, CEMMPRE, ARISE, University of Coimbra, Rua Luis Reis Santos, 3030-788, Coimbra, Portugal
2 shared publicationsJoao Oliveira
Department of Mechanical Engineering, CEMMPRE, ARISE, University of Coimbra, Rua Luis Reis Santos, 3030-788, Coimbra, Portugal
2 shared publications- João Carlos Oliveira
Department of Mechanical Engineering, CEMMPRE, University of Coimbra, Rua Luis Reis Santos, 3030-788 Coimbra, Portugal
2 shared publications Ricardo Serra
Department of Mechanical Engineering, CEMMPRE, ARISE, University of Coimbra, Rua Luis Reis Santos, 3030-788, Coimbra, Portugal
2 shared publications
Latest Publications
- Open Access
- 19 June 2024
- Published by Elsevier in Applied Surface Science
- Vol. 669
Quantification of the sp3 content in Diamond-Like carbon Films: Effects of Ne plasma addition in Deep Oscillation Magnetron sputtering
- 19 June 2024
- Published by Elsevier in Applied Surface Science
- Vol. 669
Open AccessQuantification of the sp3 content in Diamond-Like carbon Films: Effects of Ne plasma addition in Deep Oscillation Magnetron sputtering
- Open Access
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Thermomechanical Stability of Annealed Hard Dlc Coatings Deposited by Hipims-Doms in Ar-Ne Plasma
Increasing the operating temperature of internal combustion engines (ICE) to enhance their thermodynamic efficiency is a cause for concern about the thermomechanical stability of diamond-like carbon (DLC) coatings for application in ICE. Deep oscillation magnetron sputtering (DOMS), a variant of high-power impulse magnetron sputtering (HiPIMS) is a promising deposition technique that has been used to deposit DLC films with considerably better mechanical and tribological properties than conventional sputtering methods at room temperature. In the present work, the thermomechanical stability of non-hydrogenated DLC films deposited by HiPIMS-DOMS with different ratios of Ar and Ne in the discharge gas was evaluated by applying mechanical and tribological tests as-deposited and after annealing up to 700 ºC. Moreover, the structure of the films in as-deposited and post-annealed states was assessed by the process gas content in the films and was characterized by electron microscopy and ion beam analysis (IBA) techniques. It was observed the film that deposited in pure Ar plasma had a complete Ar effusion and low-density microstructure after annealing up to 700 ºC which caused low hardness and poor tribological performance of the film. On the other hand, the film that was deposited with 50% Ne in the discharge gas maintained its density after annealing up to 700 ºC and retained its hardness at about 20 GPa with a favorable tribological performance.
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermomechanical Stability of Annealed Hard Dlc Coatings Deposited by Hipims-Doms in Ar-Ne Plasma
Increasing the operating temperature of internal combustion engines (ICE) to enhance their thermodynamic efficiency is a cause for concern about the thermomechanical stability of diamond-like carbon (DLC) coatings for application in ICE. Deep oscillation magnetron sputtering (DOMS), a variant of high-power impulse magnetron sputtering (HiPIMS) is a promising deposition technique that has been used to deposit DLC films with considerably better mechanical and tribological properties than conventional sputtering methods at room temperature. In the present work, the thermomechanical stability of non-hydrogenated DLC films deposited by HiPIMS-DOMS with different ratios of Ar and Ne in the discharge gas was evaluated by applying mechanical and tribological tests as-deposited and after annealing up to 700 ºC. Moreover, the structure of the films in as-deposited and post-annealed states was assessed by the process gas content in the films and was characterized by electron microscopy and ion beam analysis (IBA) techniques. It was observed the film that deposited in pure Ar plasma had a complete Ar effusion and low-density microstructure after annealing up to 700 ºC which caused low hardness and poor tribological performance of the film. On the other hand, the film that was deposited with 50% Ne in the discharge gas maintained its density after annealing up to 700 ºC and retained its hardness at about 20 GPa with a favorable tribological performance.
- Open Access
- 8 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (21) , 10498
Advanced Tribological Characterization of DLC Coatings Produced by Ne-HiPIMS for the Application on the Piston Rings of Internal Combustion Engines
Piston rings (PR) are known for almost a quarter of the friction losses in internal combustion engines. This research work aims to improve the tribological performance of PR by a recently developed variant of Diamond-like Carbon (DLC) coatings deposited in a mixture of Ar and Ne plasma atmosphere (Ne-DLC) by high-power impulse magnetron sputtering (HiPIMS). For the benchmark, the widely used Chromium Nitride (CrN) and DLCs deposited in pure Ar plasma atmosphere (Ar-DLC) were used. The tribological tests were performed on a block-on-ring configuration under different lubrication regimes by varying temperatures and sliding speeds. The analysis of the results was performed by Stribeck curves corresponding to each sample. An improvement of the tribological performance was observed for Ne-DLC films by up to 22.8% reduction in COF compared to CrN in the boundary lubrication regime, whereas, for the Ar-DLC film, this reduction was only 9.5%. Moreover, the Ne-DLC films achieved ultralow friction of less than 0.001 during the transition to a hydrodynamic lubrication regime due to better wettability (lower contact angle) and higher surface free energy. Increasing the Ne up to 50% in the discharge gas also leads to an increase of hardness of DLC films from 19 to 24 GPa.
- 8 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (21) , 10498
Open AccessAdvanced Tribological Characterization of DLC Coatings Produced by Ne-HiPIMS for the Application on the Piston Rings of Internal Combustion Engines
Piston rings (PR) are known for almost a quarter of the friction losses in internal combustion engines. This research work aims to improve the tribological performance of PR by a recently developed variant of Diamond-like Carbon (DLC) coatings deposited in a mixture of Ar and Ne plasma atmosphere (Ne-DLC) by high-power impulse magnetron sputtering (HiPIMS). For the benchmark, the widely used Chromium Nitride (CrN) and DLCs deposited in pure Ar plasma atmosphere (Ar-DLC) were used. The tribological tests were performed on a block-on-ring configuration under different lubrication regimes by varying temperatures and sliding speeds. The analysis of the results was performed by Stribeck curves corresponding to each sample. An improvement of the tribological performance was observed for Ne-DLC films by up to 22.8% reduction in COF compared to CrN in the boundary lubrication regime, whereas, for the Ar-DLC film, this reduction was only 9.5%. Moreover, the Ne-DLC films achieved ultralow friction of less than 0.001 during the transition to a hydrodynamic lubrication regime due to better wettability (lower contact angle) and higher surface free energy. Increasing the Ne up to 50% in the discharge gas also leads to an increase of hardness of DLC films from 19 to 24 GPa.
- Open Access
Lignin from Hardwood and Softwood Biomass as a Lubricating Additive to Ethylene Glycol
Ethylene glycol (EG)-based lubricant was prepared with dissolved organosolv lignin from birch wood (BL) and softwood (SL) biomass. The effects of different lignin types on the rheological, thermal, and tribological properties of the lignin/EG lubricants were comprehensively investigated by various characterization techniques. Dissolving organosolv lignin in EG results in outstanding lubricating properties. Specifically, the wear volume of the disc by EG-44BL is only 8.9% of that lubricated by pure EG. The enhanced anti-wear property of the EG/lignin system could be attributed to the formation of a robust lubrication film and the strong adhesion of the lubricant on the contacting metal surface due to the presence of a dense hydrogen bonding (H-bonding) network. The lubricating performance of EG-BL outperforms EG-SL, which could be attributed to the denser H-bonding sites in BL and its broader molecular weight distribution. The disc wear loss of EG-44BL is only 45.7% of that lubricated by EG-44SL. Overall, H-bonding is the major contributor to the different tribological properties of BL and SL in EG-based lubricants.
Open AccessLignin from Hardwood and Softwood Biomass as a Lubricating Additive to Ethylene Glycol
Ethylene glycol (EG)-based lubricant was prepared with dissolved organosolv lignin from birch wood (BL) and softwood (SL) biomass. The effects of different lignin types on the rheological, thermal, and tribological properties of the lignin/EG lubricants were comprehensively investigated by various characterization techniques. Dissolving organosolv lignin in EG results in outstanding lubricating properties. Specifically, the wear volume of the disc by EG-44BL is only 8.9% of that lubricated by pure EG. The enhanced anti-wear property of the EG/lignin system could be attributed to the formation of a robust lubrication film and the strong adhesion of the lubricant on the contacting metal surface due to the presence of a dense hydrogen bonding (H-bonding) network. The lubricating performance of EG-BL outperforms EG-SL, which could be attributed to the denser H-bonding sites in BL and its broader molecular weight distribution. The disc wear loss of EG-44BL is only 45.7% of that lubricated by EG-44SL. Overall, H-bonding is the major contributor to the different tribological properties of BL and SL in EG-based lubricants.