Kun Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kun Zhang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Wenhui Tang
College of Liberal Arts and Sciences, National University of Defense Technology, Changsha 410073, China
2 shared publications - Xianwen Ran
College of Liberal Arts and Sciences, National University of Defense Technology, Changsha 410073, China
2 shared publications - Haifu Wang
State Key Laboratory of Explosion Science and Safety Protection, Beijing Institute of Technology , Beijing 100081
1 shared publication - Jingyuan Zhou
College of Liberal Arts and Sciences, National University of Defense Technology, Changsha 410073, China
1 shared publication - Kunkun Fu
School of Aerospace Engineering and Applied Mechanics Tongji University Shanghai People's Republic of China
1 shared publication - Liangliang Ding
Beijing Institute of Tracing Telecommunication Technology, Beijing 100028, China
1 shared publication
Latest Publications
- Open Access
Research on the Penetration Characteristics of PELE Projectile with Reactive Inner Core
With the improvement of protection technology, the damage power of conventional penetrators has become increasingly inferior. Reactive material is a new type of energetic material, which has strong energy release capabilities under high-velocity-impact conditions. In this paper, the reactive materials were put into the penetrator, and its penetration characteristics were studied. First, the penetrator with enhanced lateral effect (PELE) projectile structure with better penetration capability was obtained by numerical simulation. Then, based on the established polytetrafluoroethylene (PTFE)/Al reactive material reaction model, the numerical simulation and experimental research of the PELE projectile with a reactive inner core penetrating the target were carried out. The results show that the simulation results are in good agreement with the experimental results, which verifies the confidence of the numerical simulation. The PELE projectile had a significant increase in power with the use of a truncated conical head and reactive materials. The residual velocity of the truncated cone PELE projectile increases by 8.41–21% over conventional PELE projectiles. Its damage range is 43% higher than that of conventional penetrators. The simulation method and the conclusions obtained in this paper can provide support and reference for further research on reactive materials and on effectively improving the damage power of the penetrator.
Open AccessResearch on the Penetration Characteristics of PELE Projectile with Reactive Inner Core
With the improvement of protection technology, the damage power of conventional penetrators has become increasingly inferior. Reactive material is a new type of energetic material, which has strong energy release capabilities under high-velocity-impact conditions. In this paper, the reactive materials were put into the penetrator, and its penetration characteristics were studied. First, the penetrator with enhanced lateral effect (PELE) projectile structure with better penetration capability was obtained by numerical simulation. Then, based on the established polytetrafluoroethylene (PTFE)/Al reactive material reaction model, the numerical simulation and experimental research of the PELE projectile with a reactive inner core penetrating the target were carried out. The results show that the simulation results are in good agreement with the experimental results, which verifies the confidence of the numerical simulation. The PELE projectile had a significant increase in power with the use of a truncated conical head and reactive materials. The residual velocity of the truncated cone PELE projectile increases by 8.41–21% over conventional PELE projectiles. Its damage range is 43% higher than that of conventional penetrators. The simulation method and the conclusions obtained in this paper can provide support and reference for further research on reactive materials and on effectively improving the damage power of the penetrator.
- Open Access
A Method to Optimize the Electron Spectrum for Simulating Thermo-Mechanical Response to X-ray Radiation
The X-ray pulse originating from high altitude nuclear detonation (HAND) is mainly soft X-ray and its intensity is high enough to gasify the penetrated material and then lead to the severe thermo-mechanical deformation of unpenetrated material from the gasified blow-off effect. This effect cannot be directly reproduced in a lab for the lack of the X-ray source like HAND. At present, the low-energy relativistic electron beams resulting from an electron accelerator are usually used to approximately reproduce this effect, but the difference in the energy-deposited profile in materials between the electron and X-ray cannot be eliminated. In this paper, the symmetric linear least squares method was used to optimize the electron spectrum, and the general Monte Carlo N-Particle Transport Code calculations showed the optimized spectrum can produce the same energy-deposited profile in aluminum, copper, and tantalum with the soft X-rays like 1 keV or 3 keV spectrums. This indicates that it is possible to simulate the severe thermo-mechanical deformation resulting from HAND using the optimized electron spectrums.
Open AccessA Method to Optimize the Electron Spectrum for Simulating Thermo-Mechanical Response to X-ray Radiation
The X-ray pulse originating from high altitude nuclear detonation (HAND) is mainly soft X-ray and its intensity is high enough to gasify the penetrated material and then lead to the severe thermo-mechanical deformation of unpenetrated material from the gasified blow-off effect. This effect cannot be directly reproduced in a lab for the lack of the X-ray source like HAND. At present, the low-energy relativistic electron beams resulting from an electron accelerator are usually used to approximately reproduce this effect, but the difference in the energy-deposited profile in materials between the electron and X-ray cannot be eliminated. In this paper, the symmetric linear least squares method was used to optimize the electron spectrum, and the general Monte Carlo N-Particle Transport Code calculations showed the optimized spectrum can produce the same energy-deposited profile in aluminum, copper, and tantalum with the soft X-rays like 1 keV or 3 keV spectrums. This indicates that it is possible to simulate the severe thermo-mechanical deformation resulting from HAND using the optimized electron spectrums.
- Open Access
Modeling of Dynamic Behavior of Carbon Fiber-Reinforced Polymer (CFRP) Composite under X-ray Radiation
Carbon fiber-reinforced polymer (CFRP) composites have been increasingly used in spacecraft applications. Spacecraft may encounter highenergy-density X-ray radiation in outer space that can cause severe damage. To protect spacecraft from such unexpected damage, it is essential to predict the dynamic behavior of CFRP composites under X-ray radiation. In this study, we developed an in-house three-dimensional explicit finite element (FEM) code to investigate the dynamic responses of CFRP composite under X-ray radiation for the first time, by incorporating a modified PUFF equation-of-state. First, the blow-off impulse (BOI) momentum of an aluminum panel was predicted by our FEM code and compared with an existing radiation experiment. Then, the FEM code was utilized to determine the dynamic behavior of a CFRP composite under various radiation conditions. It was found that the numerical result was comparable with the experimental one. Furthermore, the CFRP composite was more effective than the aluminum panel in reducing radiation-induced pressure and BOI momentum. The numerical results also revealed that a 1 keV X-ray led to vaporization of surface materials and a high-magnitude compressive stress wave, whereas a low-magnitude stress wave was generated with no surface vaporization when a 3 keV X-ray was applied.
Open AccessModeling of Dynamic Behavior of Carbon Fiber-Reinforced Polymer (CFRP) Composite under X-ray Radiation
Carbon fiber-reinforced polymer (CFRP) composites have been increasingly used in spacecraft applications. Spacecraft may encounter highenergy-density X-ray radiation in outer space that can cause severe damage. To protect spacecraft from such unexpected damage, it is essential to predict the dynamic behavior of CFRP composites under X-ray radiation. In this study, we developed an in-house three-dimensional explicit finite element (FEM) code to investigate the dynamic responses of CFRP composite under X-ray radiation for the first time, by incorporating a modified PUFF equation-of-state. First, the blow-off impulse (BOI) momentum of an aluminum panel was predicted by our FEM code and compared with an existing radiation experiment. Then, the FEM code was utilized to determine the dynamic behavior of a CFRP composite under various radiation conditions. It was found that the numerical result was comparable with the experimental one. Furthermore, the CFRP composite was more effective than the aluminum panel in reducing radiation-induced pressure and BOI momentum. The numerical results also revealed that a 1 keV X-ray led to vaporization of surface materials and a high-magnitude compressive stress wave, whereas a low-magnitude stress wave was generated with no surface vaporization when a 3 keV X-ray was applied.