BWBasma I. Waisi

Basma I. Waisi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Basma I. Waisi has a total of 51 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Sustainable air gap membrane distillation using recycled acrylic (RA) membranes: Application to Shatt Al-Arab water desalination

    by Safa. N. Mohammed, Basma I. Waisi

    One of the research motivations in the MD field is to develop high-performance membranes by preparing hydrophobic membranes due to their high throughput and rejection. The current work focuses on the fabrication and performance evaluation of electrospun nanofiber membranes using recycled acrylic (Polymethyl Methacrylate) (RA) via air gap membrane distillation (AGMD). Recycling this material not only reduces plastic waste and pollution, but it also offers a low-cost alternative to virgin polymers, which aids in membrane fabrication. Scanning Electron Microscopy (SEM) confirmed a uniform, highly porous nanofibrous structure with interconnected pores in the prepared nanofiber membranes. Atomic Force Microscopy (AFM) revealed a rough surface morphology, while water contact angle measurements exceeding 121° indicated excellent hydrophobicity, critical for effective liquid-vapor separation. Fourier-transform infrared spectroscopy (FTIR) verified the preservation of key ester functional groups, confirming the chemical integrity of the RA. The assessments revealed that the electrospun nanofibers demonstrated considerable flexibility while preserving their structural and surface characteristics as evaluated through mechanical strength testing. The resulting membranes were utilized in a water desalination process employing an AGMD setup, tested under varying feed temperatures (45, 55, and 65°C) and flow rates (0.2, 0.3, and 0.4 L/min) to evaluate their impact on desalination efficiency. It was observed that increasing the feed temperature significantly boosted water flux; moreover, the feed flow rate notably improved permeate flux within AGMD systems, thereby enhancing mass and heat transfer capabilities. The highest permeate flux recorded was approximately 19 kg/m²·hr, achieved at a temperature of 65°C with a flow rate of 0.3 L/min and a salt rejection rate of 99.999%. Consequently, this study's results indicate that RA-based nanofiber membranes hold potential for sustainable and effective water desalination. Furthermore, AGMD proved to be highly efficient in salt removal from the Shatt al-Arab river and may serve as a viable solution for providing clean drinking water in southern Iraq.


  • Open Access

    Structure-Performance Engineering of Recycled Acrylic Membranes for Air Gap Membrane Distillation

    by Safa Mohammed, Basma Waisi

    Air Gap Membrane Distillation (AGMD) is an emerging and promising technology in separation processes, but its industrial adoption is limited by relatively low permeate flux. Conventional AGMD systems typically utilise thin film-cast polymeric membranes. However, electrospun nanofibrous membranes have become more popular since they possess a highly interconnected porous structure, which is able to increase mass transfer performance and availability. In this study, recycled acrylic (RA) waste powder was used to prepare a precursor solution to fabricate two types of membranes: thin film-cast membranes and electrospun nonwoven nanofibrous membranes to be evaluated in the AGMD process for water desalination application. The fabricated RA-based membranes underwent characterisation by scanning electronic microscopy (SEM), mechanical properties, water contact angle (WCA), and Fourier transform infrared spectroscopy (FTIR). Based on the results obtained, the nanofiber membrane exhibited a higher contact angle, porosity, and elasticity than the thin film cast membrane. RA-based membranes were tested in the AGMD system at different feed temperatures (45 °C, 55 °C, and 65 °C). The electrospun nanofibrous membrane performed better than the thin-film cast membrane in both permeate flux and salt rejection. The temperature of the feed increased correspondingly with the flux of permeate as well as the salt rejection. The cast membrane of thin film attained a flux of permeate of 1.48 kg/(m 2 ‧h) with 99.98 % salt rejection. Conversely, the electrospun nanofibrous membrane had better performance with a significantly higher permeate flux rate of 7.69 kg/(m 2 ‧h) and an almost ideal salt rejection of 99.99 %.

  • Open Access

    Sustainable superhydrophobic composite nanofiber membranes for desalination via air gap membrane distillation

    by Safa N. Mohammed, Basma I. Waisi

    Super-hydrophobic nanofiber membranes have recently demonstrated significant potential as desirable approaches for membrane distillation and are favored because of their high vapor flux and remarkable salt rejection capabilities. This paper presents the design and testing of electrospun nanofiber...

  • Open Access

    Design of porous activated carbon beads: Controlling size and structure for optimal dye adsorption

    by Basma I. Waisi, Wafaa Kh. Al-Musawy, Shaalan B. Ahmed, Mustafa H. Al-Furaiji


  • Open Access

    Crystal Violet Dye Removal from Aqueous Solution Using Corn Silks as an Environmentally Friendly Adsorbent

    by Israa Sabeeh Al-Bayati, Basma I. Waisi, Manal A. Mohammed, Asrar A. Alobaidy, Mohammed A. Kadhom

    As today’s world faces a crucial water crisis due to increased population and associated development, finding alternative and renewable resources has become necessary. Adsorption is a simple and effective process; when biowaste is applied for this purpose, a reasonable solution is proposed in terms of economical and influential sectors. In the present work, corn silks, usually considered useless, were used to remove the crystal violet dye from a simulated aqueous solution. Different experimental parameters were investigated: solution pH and temperature, adsorbent dose, mixing speed, adsorbate concentration, and contact time. The corn silks were characterized via the SEM microscope, while the chemical functional groups were analyzed using the Fourier transform infrared (FTIR) spectra analysis. The theoretical calculations of adsorption isotherm, kinetics, and thermodynamics were considered to comprehend adsorption nature. The results revealed that as the solution pH reached normality, the highest adsorption removal rate was achieved. After 70 min contact time, the adsorption capacity at a pH of 6.5 was 6.44 mg/g, and the removal rate was 95.5%. Furthermore, the temperature effect test and thermodynamic study showed that the adsorption process was endothermic. However, the adsorption removal rate increased by increasing the adsorbent dose and agitation speed to a certain contact time, and then all became analogous. The dye concentration showed identical behavior, indicating the high adsorption tendency of corn silks. Lastly, the best-fit isotherm and kinetic models were the Freundlich and Pseudo second-order models, respectively.

  • Open Access

    Mathematical and experimental study of the direct contact membrane distillation method for desalination using a hydrophobic electrospun nanofibers membrane

    by Nawras N. Safi, Basma I. Waisi

    This paper examines the performance of a Direct Contact Membrane Distillation (DCMD) system experimentally and theoretically. The system uses a super hydrophobic electrospun nanofiber membrane to desalinate water. Investigations were carried out into how the feed concentration, feed flow rate, and feed temperature affected permeate flux. as system operating parameters to aid in comprehending the factors impacting the DCMD process. The application of DOE and Taguchi methods achieved statistical optimization of the DCMD process's performance. In addition, the study of mass and heat transport in DCMD was described by a theoretical model. While the feed concentration (0- 210 g/L) significantly affected flux, the feed's temperature (35-55 °C) and flow rate (0.2-0.6 L/min) mostly dominated the impact on system performance. The created model numerically solved the DCMD process using MATLAB software, describing it as a system of nonlinear equations. Various operating conditions were used to investigate the efficiency of the superhydrophobic electrospun nanofiber membrane in treating 210 g/L NaCl salt water. Changing the feed temperature and concentration affected the hypothetically suggested path across the membrane, according to the simulation results presented in this paper. Excellent agreement was observed between the experiment results and the constructed model's predicted results. Every instance maintained a high salt rejection rate (over 99.9%). The DCMD produced a gain output ratio (GOR) of 0.87 and a temperature polarization coefficient of 0.78 to 0.91. The system achieved a maximum thermal efficiency of 73.5%. The optimal parameters, which are 70 g/L, 0.6 L/min, and 55°C.

  • Open Access

    Adsorption Isotherms and Kinetics Studies of Lead on Polyacrylonitrile-Based Activated Carbon Nonwoven Nanofibres

    by Basma I. Waisi, Israa S. Al-Bayati, Asrar A. Alobaidy, Mohammed A. Manal

    Activated carbon nonwoven nanofibers (ACNN) mat derived from polyacrylonitrile was manufactured through the electrospinning method followed by thermal treatment steps. The ACNN ability to adsorb Pb(II) from a liquid solution was evaluated. The fabricated ACNN was characterized using Scanning...

  • Open Access

    Performance Enhancement of Polyethersulfone-Based Ultrafiltration Membrane Decorated by Titanium Dioxide Nanoparticles for Dye Filtration

    by Ihal A. Abed, Basma I. Waisi

    This study describes the modification of a Polyethersulfone (PES)-based membrane by embedding TiO2 nanoparticles. The prepared composite membranes are then characterized and applied for Melechate Green Dye (MG) filtration from water to asses its filtering capabilities. The effect of TiO2 contents...


  • Open Access

    Enhanced Hydrophobic Double-Layer Nanofibers Membranes for Direct Contact Membrane Distillation

    by Nawras N. Safi, Basma I. Waisi

    There are several uses for electrospun nanofiber membranes because of their unique properties. Electrospinning, under suitable conditions, has allowed for the successful fabrication of nanofibrous membranes. This research, a dual-layer membrane was prepared and applied in a direct contact...


  • Open Access

    Water Treatment Performance of PAN/HPMC/Gr Nano Composites

    by Masar A. Akaood, Iftikhar M. Ali, Basma I. Waisi

    This study investigates polyacrylonitrile:hydroxypropyl methylcellulose )PAN:HPMC( and PAN:HPMC: graphene (Gr) composite nanofibers prepared using the electrospinning technique. Electrospinning is a simple and versatile technique that relies on the electrostatic repulsion between surface charges to continuously draw nanofibers from a viscoelastic fluid. Membrane technology is vital in removing contaminants due to its easy handling and high efficiency. The results demonstrated that the Gr was successfully incorporated into the PAN:HPMC nanofiber membranes, as confirmed by scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) measurements. The Gr content has a significant impact on the diameter, porosity, and pore size. The PAN:HPMC:0.02Gr electrospun nanofiber membranes achieved excellent oil rejection (72.47%) and good permeability flux (750 LMH); this might be a result of how well the functional groups of the equally distributed Gr within the PAN:HPMC nanofibers interacted with oil. It was noticed that oil rejection dropped a lot as the Gr content went up. This is likely because the pores got wider and some of the Gr stacked or agglomerated across the nanofibers.