Qian Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Qian Li has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Hongfei Ye
State Key Laboratory of Structural Analysis, Optimization and CAE Software for Industrial Equipment, Department of Engineering Mechanics, School of Mechanics and Aerospace Engineering, Dalian University of Technology, Dalian 116024, P. R. China
3 shared publications Jiayong Zhang
3 shared publications- Yonggang Zheng
State Key Laboratory of Structural Analysis, Optimization and CAE Software for Industrial Equipment, Department of Engineering Mechanics, School of Mechanics and Aerospace Engineering Dalian University of Technology Dalian People's Republic of China
3 shared publications Huayuan Tang
2 shared publications- Jia Sun
International Research Center for Computational Mechanics, State Key Laboratory of Structural Analysis for Industrial Equipment, Department of Engineering Mechanics, Faculty of Vehicle Engineering and Mechanics, Dalian University of Technology, Dalian 116024, PR China
2 shared publications Hong Wu Zhang
Dalian University of Technology, Dalian, Liaoning, China
1 shared publication
Latest Publications
- 9 November 2020
- Published by IOP Publishing in Physica Scripta
- Vol. 96 (1) , 015701
Nanostructural characteristics-mediated plastic behavior of Cu/Ag polycrystalline multilayered materials
For polycrystalline multilayers materials, the typical nanoscale structural characteristics contain grain, twin and hetero interface, which could make collective and remarkable influence on the mechanical property. In this work, taking Cu/Ag polycrystalline multilayers as an example, the coupling effects of grain boundary, twin boundary and hetero interface on the plastic deformation mechanisms are studied using molecular dynamics simulations. The simulation results show that the dominant plastic deformation mechanisms change from dislocation activities for common multilayer material to hetero interfaces sliding when the ratio of material layer thickness to grain size is small enough, leading to a marked decrease of strength. As for the twin boundary, its strengthening effect follows the conventional Hall-Petch relationship when the grain size is larger than the twin thickness. This twin-related strengthening effect becomes weak with the grain size decreases, indicating a competitive relationship between these two characteristic sizes. These findings will shed light on a more comprehensive understanding of size effects on the underlying mechanisms of plastic deformation of polycrystalline multilayers, which provide crucial guidance for the design of novel materials based on polycrystalline multilayers.
- 9 November 2020
- Published by IOP Publishing in Physica Scripta
- Vol. 96 (1) , 015701
Nanostructural characteristics-mediated plastic behavior of Cu/Ag polycrystalline multilayered materials
For polycrystalline multilayers materials, the typical nanoscale structural characteristics contain grain, twin and hetero interface, which could make collective and remarkable influence on the mechanical property. In this work, taking Cu/Ag polycrystalline multilayers as an example, the coupling effects of grain boundary, twin boundary and hetero interface on the plastic deformation mechanisms are studied using molecular dynamics simulations. The simulation results show that the dominant plastic deformation mechanisms change from dislocation activities for common multilayer material to hetero interfaces sliding when the ratio of material layer thickness to grain size is small enough, leading to a marked decrease of strength. As for the twin boundary, its strengthening effect follows the conventional Hall-Petch relationship when the grain size is larger than the twin thickness. This twin-related strengthening effect becomes weak with the grain size decreases, indicating a competitive relationship between these two characteristic sizes. These findings will shed light on a more comprehensive understanding of size effects on the underlying mechanisms of plastic deformation of polycrystalline multilayers, which provide crucial guidance for the design of novel materials based on polycrystalline multilayers.
- 11 July 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (36) , 365304
Gradient structure regulated plastic deformation mechanisms in polycrystalline nanotwinned copper
Molecular dynamics simulations are performed to investigate the effects of grain size gradient and twin thickness gradient on uniaxial tensile deformation behaviors of gradient-structured polycrystalline copper. Simulation results reveal that there exist an inverse Hall–Petch effect and gradient structure regulated plastic deformation mechanisms. That is, the average flow stress of the gradient nanograined (GNG) model or the gradient nanotwinned (GNT) model decreases with decreasing the grain size or twin boundary (TB) spacing, exhibiting the breakdown in the Hall-Petch relationship when the grain size or TB spacing is smaller than a critical size. The dominant plastic deformation mechanism is found to transform from the grain boundary (GB)-mediated one to the dislocation-based counterpart with the increase of the applied strain in the GNG model. The TB migration and annihilation dominate the plastic deformation in the grains with small TB spacing; while in the grains with large TB spacing, the dislocation multiplication and cutting across TB are mainly responsible for accommodating the deformation in the GNT model. Furthermore, the gradient distribution of strain and incompatibility of deformation induced by GB or TB gradient distribution are observed by monitoring the microstructural evolution.
- 11 July 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (36) , 365304
Gradient structure regulated plastic deformation mechanisms in polycrystalline nanotwinned copper
Molecular dynamics simulations are performed to investigate the effects of grain size gradient and twin thickness gradient on uniaxial tensile deformation behaviors of gradient-structured polycrystalline copper. Simulation results reveal that there exist an inverse Hall–Petch effect and gradient structure regulated plastic deformation mechanisms. That is, the average flow stress of the gradient nanograined (GNG) model or the gradient nanotwinned (GNT) model decreases with decreasing the grain size or twin boundary (TB) spacing, exhibiting the breakdown in the Hall-Petch relationship when the grain size or TB spacing is smaller than a critical size. The dominant plastic deformation mechanism is found to transform from the grain boundary (GB)-mediated one to the dislocation-based counterpart with the increase of the applied strain in the GNG model. The TB migration and annihilation dominate the plastic deformation in the grains with small TB spacing; while in the grains with large TB spacing, the dislocation multiplication and cutting across TB are mainly responsible for accommodating the deformation in the GNT model. Furthermore, the gradient distribution of strain and incompatibility of deformation induced by GB or TB gradient distribution are observed by monitoring the microstructural evolution.
- 17 April 2019
- Published by IOP Publishing in Nanotechnology
- Vol. 30 (27) , 275702
Regulating the mechanical properties of nanocrystalline nickel via molybdenum segregation: an atomistic study
The effects of segregation of impurity molybdenum (Mo) atoms on the tensile mechanical properties of nanocrystalline nickel (Ni) are investigated with molecular dynamics simulation. The results show that the segregation of Mo atoms induces an obvious increase in the elastic modulus and strength of nanocrystalline Ni, and the strengthening effect is more significant with smaller grain size. When the grain size decreases below a critical value, at which the softening occurs in non-segregated Ni-Mo alloy, no evident softening phenomenon is observed in Mo-segregated systems. Furthermore, based on a bicrystal configuration, it is found that Mo atoms segregating to the grain boundary reduce the energy and mobility of the grain boundary, increasing the grain boundary stability and thus accommodating the strengthening. The present findings will shed light on the fabrication of high strength nanocrystalline materials by controlling the segregation of atoms.
- 17 April 2019
- Published by IOP Publishing in Nanotechnology
- Vol. 30 (27) , 275702
Regulating the mechanical properties of nanocrystalline nickel via molybdenum segregation: an atomistic study
The effects of segregation of impurity molybdenum (Mo) atoms on the tensile mechanical properties of nanocrystalline nickel (Ni) are investigated with molecular dynamics simulation. The results show that the segregation of Mo atoms induces an obvious increase in the elastic modulus and strength of nanocrystalline Ni, and the strengthening effect is more significant with smaller grain size. When the grain size decreases below a critical value, at which the softening occurs in non-segregated Ni-Mo alloy, no evident softening phenomenon is observed in Mo-segregated systems. Furthermore, based on a bicrystal configuration, it is found that Mo atoms segregating to the grain boundary reduce the energy and mobility of the grain boundary, increasing the grain boundary stability and thus accommodating the strengthening. The present findings will shed light on the fabrication of high strength nanocrystalline materials by controlling the segregation of atoms.