Min Yan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Min Yan has a total of 148 co-authors. Here are the top co-authors by number of shared publications:
- Ping Shum
State Key Laboratory of Optical Fiber and Cable Manufacture Technology, Department of EEE, Southern University of Science and Technology, Shenzhen, China
19 shared publications - Min Qiu
Westlake University
16 shared publications - Jin Dai
Department of Materials and Nano Physics, School of Information and Communication Technology, KTH-Royal Institute of Technology, Electrum 229, 16440 Kista, Sweden
7 shared publications P. Shum
Network Technology Research Centre, Nanyang Technological University, Research TechnoPlaza, 50 Nanyang Drive, Singapore, 637553
5 shared publicationsYiting Chen
Optics and Photonics, School of Information and Communication Technology, KTH - Royal Institute of Technology, Electrum 229, 164 40 Kista, Sweden
5 shared publicationsL. Wosinski
School of Information and Communication Technology, Royal Institute of Technology, Stockholm, 16440, Sweden
4 shared publications
Latest Publications
- 28 February 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11781, 117810N-88
Influence of power ratio of the main amplifier to master oscillator on slope efficiency
In a typical multi-kW industrial fiber laser, the influence of the main amplifier to master oscillator power ratio on laser performance has been fully demonstrated. An optimized output power ratio is obtained to be ~5, which can provide the maximum main amplifier slope efficiency of ~78.2% at multi-kW laser output. In this case, the laser setup was kept at ∼2.6kW for 1h and the output power presented a relatively small power degradation of 0.36%. It was found the injected seed power has no remarkable effect on the optimal slope efficiency for industry fiber laser. The present results indicated that a suitable power ratio between the main amplifier and the oscillator is of great importance for the power scaling up and high stability of industry fiber laser.
- 28 February 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11781, 117810N-88
Influence of power ratio of the main amplifier to master oscillator on slope efficiency
In a typical multi-kW industrial fiber laser, the influence of the main amplifier to master oscillator power ratio on laser performance has been fully demonstrated. An optimized output power ratio is obtained to be ~5, which can provide the maximum main amplifier slope efficiency of ~78.2% at multi-kW laser output. In this case, the laser setup was kept at ∼2.6kW for 1h and the output power presented a relatively small power degradation of 0.36%. It was found the injected seed power has no remarkable effect on the optimal slope efficiency for industry fiber laser. The present results indicated that a suitable power ratio between the main amplifier and the oscillator is of great importance for the power scaling up and high stability of industry fiber laser.
- 2 June 2020
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 22 (25) , 13965-13974
Scalable spectrally selective mid-infrared meta-absorbers for advanced radiative thermal engineering
Selective broadband meta-absorbers in the mid-infrared range are achieved using residual fluctuation in diameters of resonators etched by monodisperse colloidal particles.
- 2 June 2020
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 22 (25) , 13965-13974
Scalable spectrally selective mid-infrared meta-absorbers for advanced radiative thermal engineering
Selective broadband meta-absorbers in the mid-infrared range are achieved using residual fluctuation in diameters of resonators etched by monodisperse colloidal particles.
- Open Access
Complex-k modes of plasmonic chain waveguides
Nanoparticle chain waveguide based on negative-epsilon material is investigated through a generic 3D finite-element Bloch-mode solver which derives complex propagation constant ($k$). Our study starts from waveguides made of non-dispersive material, which not only singles out "waveguide dispersion" but also motivates search of new materials to achieve guidance at unconventional wavelengths. Performances of gold or silver chain waveguides are then evaluated; a concise comparison of these two types of chain waveguides has been previously missing. Beyond these singly-plasmonic chain waveguides, we examine a hetero-plasmonic chain system with interlacing gold and silver particles, inspired by a recent proposal; the claimed enhanced energy transfer between gold particles appears to be a one-sided view of its hybridized waveguiding behavior --- energy transfer between silver particles worsens. Enabled by the versatile numerical method, we also discuss effects of inter-particle spacing, background medium, and presence of a substrate. Our extensive analyses show that the general route for reducing propagation loss of e.g. a gold chain waveguide is to lower chain-mode frequency with a proper geometry (e.g. smaller particle spacing) and background material setting (e.g. high-permittivity background or even foreign nanoparticles). In addition, the possibility of building mid-infrared chain waveguides using doped silicon is commented based on numerical simulation.
Open AccessComplex-k modes of plasmonic chain waveguides
Nanoparticle chain waveguide based on negative-epsilon material is investigated through a generic 3D finite-element Bloch-mode solver which derives complex propagation constant ($k$). Our study starts from waveguides made of non-dispersive material, which not only singles out "waveguide dispersion" but also motivates search of new materials to achieve guidance at unconventional wavelengths. Performances of gold or silver chain waveguides are then evaluated; a concise comparison of these two types of chain waveguides has been previously missing. Beyond these singly-plasmonic chain waveguides, we examine a hetero-plasmonic chain system with interlacing gold and silver particles, inspired by a recent proposal; the claimed enhanced energy transfer between gold particles appears to be a one-sided view of its hybridized waveguiding behavior --- energy transfer between silver particles worsens. Enabled by the versatile numerical method, we also discuss effects of inter-particle spacing, background medium, and presence of a substrate. Our extensive analyses show that the general route for reducing propagation loss of e.g. a gold chain waveguide is to lower chain-mode frequency with a proper geometry (e.g. smaller particle spacing) and background material setting (e.g. high-permittivity background or even foreign nanoparticles). In addition, the possibility of building mid-infrared chain waveguides using doped silicon is commented based on numerical simulation.
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics Communications
- Vol. 3 (11) , 115015
Complex-k modes of plasmonic chain waveguides
Nanoparticle chain waveguide based on negative-epsilon material is investigated through a generic 3D finite-element Bloch-mode solver which derives complex propagation constant (k). Our study starts from waveguides made of non-dispersive material, which not only singles out ‘waveguide dispersion’ but also motivates search of new materials to achieve guidance at unconventional wavelengths. Performances of gold or silver chain waveguides are then evaluated; a concise comparison of these two types of chain waveguides has been previously missing. Beyond these singly-plasmonic chain waveguides, we examine a hetero-plasmonic chain system with interlacing gold and silver particles, inspired by a recent proposal; the claimed enhanced energy transfer between gold particles appears to be a one-sided view of its hybridized waveguiding behavior—energy transfer between silver particles worsens. Enabled by the versatile numerical method, we also discuss effects of inter-particle spacing, background medium, and presence of a substrate. Our extensive analyses show that the general route for reducing propagation loss of e.g. a gold chain waveguide is to lower chain-mode frequency with a proper geometry (e.g. smaller particle spacing) and background material setting (e.g. high-permittivity background or even foreign nanoparticles). In addition, the possibility of building mid-infrared chain waveguides using doped silicon is commented based on numerical simulation.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics Communications
- Vol. 3 (11) , 115015
Open AccessComplex-k modes of plasmonic chain waveguides
Nanoparticle chain waveguide based on negative-epsilon material is investigated through a generic 3D finite-element Bloch-mode solver which derives complex propagation constant (k). Our study starts from waveguides made of non-dispersive material, which not only singles out ‘waveguide dispersion’ but also motivates search of new materials to achieve guidance at unconventional wavelengths. Performances of gold or silver chain waveguides are then evaluated; a concise comparison of these two types of chain waveguides has been previously missing. Beyond these singly-plasmonic chain waveguides, we examine a hetero-plasmonic chain system with interlacing gold and silver particles, inspired by a recent proposal; the claimed enhanced energy transfer between gold particles appears to be a one-sided view of its hybridized waveguiding behavior—energy transfer between silver particles worsens. Enabled by the versatile numerical method, we also discuss effects of inter-particle spacing, background medium, and presence of a substrate. Our extensive analyses show that the general route for reducing propagation loss of e.g. a gold chain waveguide is to lower chain-mode frequency with a proper geometry (e.g. smaller particle spacing) and background material setting (e.g. high-permittivity background or even foreign nanoparticles). In addition, the possibility of building mid-infrared chain waveguides using doped silicon is commented based on numerical simulation.
- 20 September 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (19) , 4729-4732
Subwavelength adiabatic multimode Y-junctions
Adiabatic multimode Y-junctions are extensively used for the design of multimode silicon photonics devices due to their straightforward principle in achieving mode splitting and manipulation. However, experimentally, the limited feature size achievable by lithography can greatly deteriorate the adiabatic branching property and result in large excess loss and crosstalk. Here, we propose a branch structure consisting of a circular-hole-based chirped subwavelength slot. By optimizing the holes’ radii and positions under our fabrication constraint, we designed and experimentally demonstrated both symmetric and asymmetric approximately adiabatic four-mode Y-junctions with excellent performance close to ideal Y-junctions over a broad wavelength span. Such junctions are compact, CMOS-compatible, exhibit a relatively large fabrication tolerance, and could be extended for more modes; hence they can be potentially deployed for mode-division multiplexing silicon-photonic systems.
- 20 September 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (19) , 4729-4732
Subwavelength adiabatic multimode Y-junctions
Adiabatic multimode Y-junctions are extensively used for the design of multimode silicon photonics devices due to their straightforward principle in achieving mode splitting and manipulation. However, experimentally, the limited feature size achievable by lithography can greatly deteriorate the adiabatic branching property and result in large excess loss and crosstalk. Here, we propose a branch structure consisting of a circular-hole-based chirped subwavelength slot. By optimizing the holes’ radii and positions under our fabrication constraint, we designed and experimentally demonstrated both symmetric and asymmetric approximately adiabatic four-mode Y-junctions with excellent performance close to ideal Y-junctions over a broad wavelength span. Such junctions are compact, CMOS-compatible, exhibit a relatively large fabrication tolerance, and could be extended for more modes; hence they can be potentially deployed for mode-division multiplexing silicon-photonic systems.
- Open Access
- 4 September 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (38) , 35451-35457
Thickness Dependence of Optical Transmittance of Transparent Wood: Chemical Modification Effects
Transparent wood (TW) is an emerging optical material combining high optical transmittance and haze for structural applications. Unlike non-scattering absorbing media, the thickness dependence of light transmittance for TW is complicated since optical losses are also related to increased photon path length from multiple scattering. In the present study, starting from photon diffusion equation, it is found that the angle-integrated total light transmittance of TW has an exponentially decaying dependence on sample thickness. The expression reveals an attenuation coefficient which depends not only on the absorption coefficient but also on the diffusion coefficient. The total transmittance and thickness were measured for a range of TW samples, from both acetylated and non-acetylated balsa wood templates, and were fitted according to the derived relationship. The fitting gives a lower attenuation coefficient for the acetylated TW compared to the non-acetylated one. The lower attenuation coefficient for the acetylated TW is attributed to its lower scattering coefficient or correspondingly lower haze. The attenuation constant resulted from our model hence can serve as a singular material parameter that facilitates cross-comparison of different sample types, at even different thicknesses, when total optical transmittance is concerned. The model was verified with two other TWs (ash and birch) and is in general applicable to other scattering media.
- 4 September 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (38) , 35451-35457
Open AccessThickness Dependence of Optical Transmittance of Transparent Wood: Chemical Modification Effects
Transparent wood (TW) is an emerging optical material combining high optical transmittance and haze for structural applications. Unlike non-scattering absorbing media, the thickness dependence of light transmittance for TW is complicated since optical losses are also related to increased photon path length from multiple scattering. In the present study, starting from photon diffusion equation, it is found that the angle-integrated total light transmittance of TW has an exponentially decaying dependence on sample thickness. The expression reveals an attenuation coefficient which depends not only on the absorption coefficient but also on the diffusion coefficient. The total transmittance and thickness were measured for a range of TW samples, from both acetylated and non-acetylated balsa wood templates, and were fitted according to the derived relationship. The fitting gives a lower attenuation coefficient for the acetylated TW compared to the non-acetylated one. The lower attenuation coefficient for the acetylated TW is attributed to its lower scattering coefficient or correspondingly lower haze. The attenuation constant resulted from our model hence can serve as a singular material parameter that facilitates cross-comparison of different sample types, at even different thicknesses, when total optical transmittance is concerned. The model was verified with two other TWs (ash and birch) and is in general applicable to other scattering media.
- Top Cited PapersOpen Access
- 7 May 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (22) , 20465-20472
Transparent Wood for Thermal Energy Storage and Reversible Optical Transmittance
Functional load-bearing materials based on phase-change materials (PCMs) are under rapid development for thermal energy storage (TES) applications. Mesoporous structures are ideal carriers for PCMs and guarantee shape stability during the thermal cycle. In this study, we introduce transparent wood as a thermal energy storage system. A shape-stabilized PCM based on polyethylene glycol is encapsulated into a delignified wood substrate, and the transparent wood obtained is fully characterized, also in terms of nano- and mesoscale structures. Transparent wood for thermal energy storage (TW-TES) combines large latent heat (~76 J g-1) with switchable optical transparency. During the heating process, optical transmittance increases by 6% and reaches 68% for 1.5 mm thick TW-TES. Characterization of the thermal energy regulation performance shows that the prepared TW-TES composite is superior to normal glass, due to the combination of good heat-storage and thermal insulation properties. This makes TW-TES composites interesting candidates for applications in energy-saving buildings.
- 7 May 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (22) , 20465-20472
Top Cited PapersOpen AccessTransparent Wood for Thermal Energy Storage and Reversible Optical Transmittance
Functional load-bearing materials based on phase-change materials (PCMs) are under rapid development for thermal energy storage (TES) applications. Mesoporous structures are ideal carriers for PCMs and guarantee shape stability during the thermal cycle. In this study, we introduce transparent wood as a thermal energy storage system. A shape-stabilized PCM based on polyethylene glycol is encapsulated into a delignified wood substrate, and the transparent wood obtained is fully characterized, also in terms of nano- and mesoscale structures. Transparent wood for thermal energy storage (TW-TES) combines large latent heat (~76 J g-1) with switchable optical transparency. During the heating process, optical transmittance increases by 6% and reaches 68% for 1.5 mm thick TW-TES. Characterization of the thermal energy regulation performance shows that the prepared TW-TES composite is superior to normal glass, due to the combination of good heat-storage and thermal insulation properties. This makes TW-TES composites interesting candidates for applications in energy-saving buildings.
- 12 April 2019
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 52 (8) , 3131-3140
Nanostructure and Properties of Nacre-Inspired Clay/Cellulose Nanocomposites—Synchrotron X-ray Scattering Analysis
- 12 April 2019
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 52 (8) , 3131-3140
Nanostructure and Properties of Nacre-Inspired Clay/Cellulose Nanocomposites—Synchrotron X-ray Scattering Analysis
- Open Access
- 13 December 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 6 (3) , 1094-1101
Towards centimeter thick transparent wood through interface manipulation
A centimeter-thick transparent wood structure was realized through interface manipulation.
- 13 December 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 6 (3) , 1094-1101
Open AccessTowards centimeter thick transparent wood through interface manipulation
A centimeter-thick transparent wood structure was realized through interface manipulation.
- 4 April 2016
- Published by American Physical Society (APS) in Physical Review B
- Vol. 93 (15) , 155403
Radiative heat transfer between two dielectric-filled metal gratings
Nanoscale surface corrugation is known to be able to drastically enhance radiative heat transfer between two metal plates. Here we numerically calculate the radiative heat transfer between two dielectric-filled metal gratings at dissimilar temperatures based on a scattering approach. It is demonstrated that, compared to unfilled metal gratings, the heat flux for a fixed geometry can be further enhanced, by up to 650% for the geometry separated by a vacuum gap of and temperature values concerned in our study. The enhancement in radiative heat transfer is found to depend on refractive index of the filling dielectric, the specific grating temperatures, and naturally the gap size between the two gratings. The enhancement can be understood through examining the transmission factor spectra, especially the spectral locations of the spoof surface plasmon polariton modes. Of more practical importance, it's shown that the radiative heat flux can exceed that between two planar SiC plates with same thickness, separation, and temperature settings over a wide temperature range. This reaffirms that one can harness rich electromagnetic modal properties in nanostructured materials for efficient thermal management at nanoscale.- 4 April 2016
- Published by American Physical Society (APS) in Physical Review B
- Vol. 93 (15) , 155403
Radiative heat transfer between two dielectric-filled metal gratings
Nanoscale surface corrugation is known to be able to drastically enhance radiative heat transfer between two metal plates. Here we numerically calculate the radiative heat transfer between two dielectric-filled metal gratings at dissimilar temperatures based on a scattering approach. It is demonstrated that, compared to unfilled metal gratings, the heat flux for a fixed geometry can be further enhanced, by up to 650% for the geometry separated by a vacuum gap of and temperature values concerned in our study. The enhancement in radiative heat transfer is found to depend on refractive index of the filling dielectric, the specific grating temperatures, and naturally the gap size between the two gratings. The enhancement can be understood through examining the transmission factor spectra, especially the spectral locations of the spoof surface plasmon polariton modes. Of more practical importance, it's shown that the radiative heat flux can exceed that between two planar SiC plates with same thickness, separation, and temperature settings over a wide temperature range. This reaffirms that one can harness rich electromagnetic modal properties in nanostructured materials for efficient thermal management at nanoscale.