Ying Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ying Wang has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Ning Zhong
Merchant Marine College, Shanghai Maritime University, Shanghai 201306, China
5 shared publications - Xiaoben Qi
School of Materials Science, Shanghai DianJi University, Shanghai 201306, China
4 shared publications - Hailong Shang
School of Materials Science, Shanghai DianJi University, Shanghai 201306, China
3 shared publications - Huanqing Xu
School of Materials Science, Shanghai DianJi University, Shanghai 201306, China
2 shared publications - Peter K. Liaw
University of Tennessee
2 shared publications - Xu Wang
School of Materials Science, Shanghai DianJi University, Shanghai 201306, China
2 shared publications
Latest Publications
- 24 December 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (1) , 015109
First-principle investigation of the electronic structures of group IV and V element-doped MgIn 2 S 4 as potential intermediate band semiconductors for photovoltaic applications
Due to its direct bandgap and outstanding photoelectric performance, the MgIn 2 S 4 semiconductor has attracted widespread attention in the field of intermediate band (IB) solar cell. Therefore, we have investigated the electronic structures of group IV and V element (Si, Ge, Sn, Pb, P, As, Sb, and Bi)-doped MgIn 2 S 4 using hybrid density functional theory, aiming to identify suitable candidates for the realization of an IB. For all impurity systems, the IBs with delocalized characteristics are introduced into the forbidden gap of the host. In particular, the IBs in Ge- and Pb-doped compounds are partially occupied and completely isolated, which also results in enhanced optical absorption at lower energies. These IBs are primarily derived from the antibonding interaction between the dopants and sulfur atoms via an s–p hybridization mechanism. Additionally, charge transfer is confirmed by Bader charge analysis, which could reduce the non-radiative recombination of carriers. Finally, the results of phase stability and ab initio molecular dynamics demonstrate that these compounds possess excellent thermodynamic stability, further supporting the feasibility of their experimental synthesis.
- 24 December 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (1) , 015109
First-principle investigation of the electronic structures of group IV and V element-doped MgIn 2 S 4 as potential intermediate band semiconductors for photovoltaic applications
Due to its direct bandgap and outstanding photoelectric performance, the MgIn 2 S 4 semiconductor has attracted widespread attention in the field of intermediate band (IB) solar cell. Therefore, we have investigated the electronic structures of group IV and V element (Si, Ge, Sn, Pb, P, As, Sb, and Bi)-doped MgIn 2 S 4 using hybrid density functional theory, aiming to identify suitable candidates for the realization of an IB. For all impurity systems, the IBs with delocalized characteristics are introduced into the forbidden gap of the host. In particular, the IBs in Ge- and Pb-doped compounds are partially occupied and completely isolated, which also results in enhanced optical absorption at lower energies. These IBs are primarily derived from the antibonding interaction between the dopants and sulfur atoms via an s–p hybridization mechanism. Additionally, charge transfer is confirmed by Bader charge analysis, which could reduce the non-radiative recombination of carriers. Finally, the results of phase stability and ab initio molecular dynamics demonstrate that these compounds possess excellent thermodynamic stability, further supporting the feasibility of their experimental synthesis.
- 11 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (3) , 3711-3718
Interfacial adhesion of CVD-SiC coatings on graphite substrates: Role of temperature in microstructure and mechanical properties
- 11 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (3) , 3711-3718
Interfacial adhesion of CVD-SiC coatings on graphite substrates: Role of temperature in microstructure and mechanical properties
- Open Access
Unveiling the Regulatory Mechanism of Zr Content on the Microstructure, Mechanical Properties and Stability of Cu-Zr Nanocrystalline Alloy Films
A series of Cu-Zr nanocrystalline alloy films with varying Zr contents were fabricated via magnetron co-sputtering technology. The effect of Zr content on the microstructure and mechanical properties of the alloy films was investigated, and the strengthening mechanism was revealed. Furthermore, the stability of nanocrystalline alloy films was studied through annealing experiments at different temperatures. The results show that part of the added Zr atoms are dissolved in the Cu lattice to form a solid solution structure of Zr in Cu, while the other part segregates at the grain boundaries. No second-phase compounds or simple substances are formed in the alloy films. The addition of Zr significantly refines the grain size of the alloy films. The hardness of the films exhibits a gradual increase with the elevation of Zr content. The results indicate that there are three main strengthening factors for the alloy films: grain refinement strengthening effect (, accounting for exceeding 70%), solid solution strengthening effect (, accounting for approximately 20%) and nanocrystalline solute atom pinning strengthening effect (, accounting for less than 10%). Among them, the strengthening effect of grain refinement assumes a predominant role. Regarding stability, Zr atoms segregate at the grain boundaries of the alloy films. The segregation becomes more significant as the annealing temperature rises. This segregation of Zr atoms at the grain boundaries can exert a pinning effect on the grain boundaries and impede their migration, thus significantly improving the structural stability of the alloy films.Open AccessUnveiling the Regulatory Mechanism of Zr Content on the Microstructure, Mechanical Properties and Stability of Cu-Zr Nanocrystalline Alloy Films
A series of Cu-Zr nanocrystalline alloy films with varying Zr contents were fabricated via magnetron co-sputtering technology. The effect of Zr content on the microstructure and mechanical properties of the alloy films was investigated, and the strengthening mechanism was revealed. Furthermore, the stability of nanocrystalline alloy films was studied through annealing experiments at different temperatures. The results show that part of the added Zr atoms are dissolved in the Cu lattice to form a solid solution structure of Zr in Cu, while the other part segregates at the grain boundaries. No second-phase compounds or simple substances are formed in the alloy films. The addition of Zr significantly refines the grain size of the alloy films. The hardness of the films exhibits a gradual increase with the elevation of Zr content. The results indicate that there are three main strengthening factors for the alloy films: grain refinement strengthening effect (, accounting for exceeding 70%), solid solution strengthening effect (, accounting for approximately 20%) and nanocrystalline solute atom pinning strengthening effect (, accounting for less than 10%). Among them, the strengthening effect of grain refinement assumes a predominant role. Regarding stability, Zr atoms segregate at the grain boundaries of the alloy films. The segregation becomes more significant as the annealing temperature rises. This segregation of Zr atoms at the grain boundaries can exert a pinning effect on the grain boundaries and impede their migration, thus significantly improving the structural stability of the alloy films. - Open Access
- 7 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1687
Role of Ni Layer Thickness in Regulating Mechanical Properties and Deformation-Fracture Behavior of TiB2-Ni Multilayer Films
A series of TiB2-Ni multilayer films with different Ni layer thicknesses was prepared by magnetron sputtering technology. The effect of Ni layer thickness on the microstructure and mechanical properties of the multilayer films was investigated, and the deformation and fracture mechanisms underlying the observed behavior were analyzed in detail. The results show that all multilayer films exhibit a well-defined layered architecture with sharp interfacial boundaries. Specifically, the Ni layers grow as columnar grains with an average diameter of approximately 10 nm, while the TiB2 layers form a very fine acicular nanocolumnar structure. With the increase in Ni layer thickness, the hardness of the multilayer films shows a decreasing trend, gradually decreasing from 27.3 GPa at a 4 nm Ni thickness to 19.3 GPa at 50 nm. In contrast, the fracture toughness increases gradually from 1.54 MPa·m1/2 to 2.73 MPa·m1/2. This enhancement in toughness is primarily attributed to a transition in the deformation and fracture mechanism. With the increase in Ni layer thickness, the crack propagation mode in the multilayer films gradually changes from the integral propagation penetrating the film layers to the crack deflection propagation within the layers. This transformation is the result of the combined effect of the stress state of each layer and the crack energy dissipation.
- 7 November 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (22) , 1687
Open AccessRole of Ni Layer Thickness in Regulating Mechanical Properties and Deformation-Fracture Behavior of TiB2-Ni Multilayer Films
A series of TiB2-Ni multilayer films with different Ni layer thicknesses was prepared by magnetron sputtering technology. The effect of Ni layer thickness on the microstructure and mechanical properties of the multilayer films was investigated, and the deformation and fracture mechanisms underlying the observed behavior were analyzed in detail. The results show that all multilayer films exhibit a well-defined layered architecture with sharp interfacial boundaries. Specifically, the Ni layers grow as columnar grains with an average diameter of approximately 10 nm, while the TiB2 layers form a very fine acicular nanocolumnar structure. With the increase in Ni layer thickness, the hardness of the multilayer films shows a decreasing trend, gradually decreasing from 27.3 GPa at a 4 nm Ni thickness to 19.3 GPa at 50 nm. In contrast, the fracture toughness increases gradually from 1.54 MPa·m1/2 to 2.73 MPa·m1/2. This enhancement in toughness is primarily attributed to a transition in the deformation and fracture mechanism. With the increase in Ni layer thickness, the crack propagation mode in the multilayer films gradually changes from the integral propagation penetrating the film layers to the crack deflection propagation within the layers. This transformation is the result of the combined effect of the stress state of each layer and the crack energy dissipation.
- Open Access
- 11 August 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (35) , 40492-40500
Thermal Field Simulation and Optimization for 8 in. SiC Crystal Growth via Novel Resistance Furnace Design
Silicon carbide (SiC), a wide-band gap semiconductor, is essential for applications in electric vehicles, 5G communications, and aerospace due to its outstanding physical properties. However, their high production costs limit their widespread industrial applications. The growth of larger diameter and thicker crystals, particularly 8 in. crystals, offers the potential to reduce these costs. Therefore, large-diameter PVT crystal growth equipment with resistance heating has become a focal point of research in this field. In this paper, a novel double-flap resistance furnace design is proposed for the first time, and the thermal field is systematically studied by three-dimensional COMSOL Multiphysics modeling to optimize the growth of 8 in. 4H-SiC single crystals. It is found that the resistance heating system significantly outperforms the induction heating system by providing a lower radial temperature gradient necessary for large-diameter SiC crystals. Additionally, the influence of key parameters such as the crucible, the distance between the heater and the crucible, and the growth power on the thermal field distribution in the crucible was also systematically studied. The influence of the distance from the surface of the source material to the crystal surface and the distance from the center of the crystal to the edge on both the axial and radial temperature differences is also analyzed. Based on the simulation results, the crystal growth scheme was further optimized and an 8 in. SiC crystal with a thickness above 20 mm and resistivity uniformity was successfully obtained using the novel resistance furnace. This is of great significance for the growth of large-diameter SiC crystals.
- 11 August 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (35) , 40492-40500
Open AccessThermal Field Simulation and Optimization for 8 in. SiC Crystal Growth via Novel Resistance Furnace Design
Silicon carbide (SiC), a wide-band gap semiconductor, is essential for applications in electric vehicles, 5G communications, and aerospace due to its outstanding physical properties. However, their high production costs limit their widespread industrial applications. The growth of larger diameter and thicker crystals, particularly 8 in. crystals, offers the potential to reduce these costs. Therefore, large-diameter PVT crystal growth equipment with resistance heating has become a focal point of research in this field. In this paper, a novel double-flap resistance furnace design is proposed for the first time, and the thermal field is systematically studied by three-dimensional COMSOL Multiphysics modeling to optimize the growth of 8 in. 4H-SiC single crystals. It is found that the resistance heating system significantly outperforms the induction heating system by providing a lower radial temperature gradient necessary for large-diameter SiC crystals. Additionally, the influence of key parameters such as the crucible, the distance between the heater and the crucible, and the growth power on the thermal field distribution in the crucible was also systematically studied. The influence of the distance from the surface of the source material to the crystal surface and the distance from the center of the crystal to the edge on both the axial and radial temperature differences is also analyzed. Based on the simulation results, the crystal growth scheme was further optimized and an 8 in. SiC crystal with a thickness above 20 mm and resistivity uniformity was successfully obtained using the novel resistance furnace. This is of great significance for the growth of large-diameter SiC crystals.
- Open Access
- 31 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (3) , 229
Impact of Ni Doping on the Microstructure and Mechanical Properties of TiB2 Films
The TiB2 film exhibits exceptional hardness and chemical stability due to its unique crystal structure and robust covalent bonds, but it also demonstrates high brittleness and poor toughness, which restricts its practical applications in engineering. By appropriately incorporating metal dopants, the toughness of the ceramic matrix can be enhanced without compromising its inherent hardness. In this study, TiB2 films with different nickel contents (0–32.22 at.%) were fabricated through radio frequency magnetron sputtering. The microstructure, chemical composition, phase structure, and mechanical properties were analyzed using scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and nanoindentation tester. The pure TiB2 film exhibited (0001) and (0002) peaks; however, the addition of nickel resulted in broadening of the (0001) peak and disappearance of the (0002) peak, and no crystalline nickel or other nickel-containing phases could be identified. It was found that the incorporation of nickel refines the grain structure of titanium diboride, with nickel present in an amorphous form at the boundaries of titanium diboride, thereby forming a wrapped structure. The enrichment of nickel at the grain boundary becomes more pronounced as the nickel content is further increased, which hinders the growth of TiB2 grains, resulting in the thinning of columnar crystals and formation of nanocrystalline in the film, and the coating hardness remains above 20 GPa, when the nickel content is less than 10.83 at.%. With the increase in nickel content, titanium diboride exhibited a tendency to form an amorphous structure, while nickel became increasingly enriched at the boundaries, and the coating hardness and elastic modulus decreased. The wrapped microstructure could absorb the energy generated by compressive shear stress through plastic deformation, which should be beneficial to improve the toughness of the coatings. The addition of nickel enhanced the adhesion between the film and substrate while reducing the friction coefficient of the film. Specifically, when the nickel content reached 4.26 at.%, a notable enhancement in both nanohardness and toughness was observed for nanocomposite films.
- 31 January 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (3) , 229
Open AccessImpact of Ni Doping on the Microstructure and Mechanical Properties of TiB2 Films
The TiB2 film exhibits exceptional hardness and chemical stability due to its unique crystal structure and robust covalent bonds, but it also demonstrates high brittleness and poor toughness, which restricts its practical applications in engineering. By appropriately incorporating metal dopants, the toughness of the ceramic matrix can be enhanced without compromising its inherent hardness. In this study, TiB2 films with different nickel contents (0–32.22 at.%) were fabricated through radio frequency magnetron sputtering. The microstructure, chemical composition, phase structure, and mechanical properties were analyzed using scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and nanoindentation tester. The pure TiB2 film exhibited (0001) and (0002) peaks; however, the addition of nickel resulted in broadening of the (0001) peak and disappearance of the (0002) peak, and no crystalline nickel or other nickel-containing phases could be identified. It was found that the incorporation of nickel refines the grain structure of titanium diboride, with nickel present in an amorphous form at the boundaries of titanium diboride, thereby forming a wrapped structure. The enrichment of nickel at the grain boundary becomes more pronounced as the nickel content is further increased, which hinders the growth of TiB2 grains, resulting in the thinning of columnar crystals and formation of nanocrystalline in the film, and the coating hardness remains above 20 GPa, when the nickel content is less than 10.83 at.%. With the increase in nickel content, titanium diboride exhibited a tendency to form an amorphous structure, while nickel became increasingly enriched at the boundaries, and the coating hardness and elastic modulus decreased. The wrapped microstructure could absorb the energy generated by compressive shear stress through plastic deformation, which should be beneficial to improve the toughness of the coatings. The addition of nickel enhanced the adhesion between the film and substrate while reducing the friction coefficient of the film. Specifically, when the nickel content reached 4.26 at.%, a notable enhancement in both nanohardness and toughness was observed for nanocomposite films.
- Open Access
- 12 December 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (24) , 1990
Research on the Microstructure, Mechanical Properties and Strengthening Mechanism of Nanocrystalline Al-Mo Alloy Films
In this work, the Al-Mo nanocrystalline alloy films with Mo contents ranging from 0–10.5 at.% were prepared via magnetron co-sputtering technology. The composition and microstructure of alloy thin films were studied using XRD, TEM, and EDS. The mechanical behaviors were tested through nanoindentation. The weights of each strengthening factor were calculated and the strengthening mechanism of alloy thin films was revealed. The results indicate that a portion of Mo atoms exist in the Al lattice, forming a solid solution of Mo in Al. The other part of Mo atoms tends to segregate at the grain boundaries, and this segregation becomes more pronounced with an increase in Mo content. There are no compounds or second phases present in any alloy films. As the Mo element content increases, the grain size of the alloy films gradually decreases. The hardness of pure aluminum film is 2.2 GPa. The hardness increases with an increase in Mo content. When the Mo content is 10.5 at.%, The hardness of the film increases to a maximum value of 4.9 GPa. The fine grain (), solid solution (), and nanocrystalline solute pinning () are the three main reasons for the increase in the hardness of alloy thin films. The contribution of is the largest, accounting for over 60% of the total, while the contribution of accounts for about 30%, ranking second. The rest of the increase is due to .- 12 December 2024
- Published by MDPI AG in Nanomaterials
- Vol. 14 (24) , 1990
Open AccessResearch on the Microstructure, Mechanical Properties and Strengthening Mechanism of Nanocrystalline Al-Mo Alloy Films
In this work, the Al-Mo nanocrystalline alloy films with Mo contents ranging from 0–10.5 at.% were prepared via magnetron co-sputtering technology. The composition and microstructure of alloy thin films were studied using XRD, TEM, and EDS. The mechanical behaviors were tested through nanoindentation. The weights of each strengthening factor were calculated and the strengthening mechanism of alloy thin films was revealed. The results indicate that a portion of Mo atoms exist in the Al lattice, forming a solid solution of Mo in Al. The other part of Mo atoms tends to segregate at the grain boundaries, and this segregation becomes more pronounced with an increase in Mo content. There are no compounds or second phases present in any alloy films. As the Mo element content increases, the grain size of the alloy films gradually decreases. The hardness of pure aluminum film is 2.2 GPa. The hardness increases with an increase in Mo content. When the Mo content is 10.5 at.%, The hardness of the film increases to a maximum value of 4.9 GPa. The fine grain (), solid solution (), and nanocrystalline solute pinning () are the three main reasons for the increase in the hardness of alloy thin films. The contribution of is the largest, accounting for over 60% of the total, while the contribution of accounts for about 30%, ranking second. The rest of the increase is due to . - Open Access
- 2 October 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 2731-2743
Microstructures, physical and corrosion behavior of NiCoFeCu high-entropy alloy nanocomposite coatings electro-co-deposited with nano-Si3N4 particles
- 2 October 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 2731-2743
Open AccessMicrostructures, physical and corrosion behavior of NiCoFeCu high-entropy alloy nanocomposite coatings electro-co-deposited with nano-Si3N4 particles
- Open Access
Effect of Additive and Current Density on Microstructures and Corrosion Behavior of a Multi-Component NiFeCoCu Alloy Prepared by Electrodeposition
High-entropy alloys (HEAs) have been attracting growing interest for decades due to their unique properties. Electrodeposition provides a low-cost and convenient route for producing classified types of HEAs, compared to other synthesis techniques, making it an attention-grabbing method. However, fabricating high-quality HEAs through electrodeposition in aqueous electrolytes remains a great challenge. In this study, the effects of additives and current densities on the compositions, surface morphologies, microstructures, and corrosion behavior of the electrodeposited NiFeCoCu alloy are studied. The results indicate that saccharin plays a key role in achieving a flat and bright surface for NiFeCoCu coatings, while also relieving the internal stress and improving anti-corrosion properties. Electrodeposition under a current density of 20–40 mA/cm2 results in a uniform and dense deposit with favorable properties. The present work provides a low-cost and feasible industrial solution for the preparation of HEA coatings, which holds great potential for innovation in the field of HEA coatings through electrodeposition.
Open AccessEffect of Additive and Current Density on Microstructures and Corrosion Behavior of a Multi-Component NiFeCoCu Alloy Prepared by Electrodeposition
High-entropy alloys (HEAs) have been attracting growing interest for decades due to their unique properties. Electrodeposition provides a low-cost and convenient route for producing classified types of HEAs, compared to other synthesis techniques, making it an attention-grabbing method. However, fabricating high-quality HEAs through electrodeposition in aqueous electrolytes remains a great challenge. In this study, the effects of additives and current densities on the compositions, surface morphologies, microstructures, and corrosion behavior of the electrodeposited NiFeCoCu alloy are studied. The results indicate that saccharin plays a key role in achieving a flat and bright surface for NiFeCoCu coatings, while also relieving the internal stress and improving anti-corrosion properties. Electrodeposition under a current density of 20–40 mA/cm2 results in a uniform and dense deposit with favorable properties. The present work provides a low-cost and feasible industrial solution for the preparation of HEA coatings, which holds great potential for innovation in the field of HEA coatings through electrodeposition.
- Open Access
- 5 March 2019
- Published by Taylor & Francis in Heat Treatment and Surface Engineering
- Vol. 1 (1-2) , 2-10
The twice softening of martensitic matrix in Q–P–T steels and its effect on ductility
When a Si-containing steel is subjected to quenching-partitioning-tempering (Q–P–T) process, it will become a martensitic steel with considerable volume of retained austenite, which is attributed to the partitioning of carbon from martensite to retained austenite leading to carbon-depletion in martensitic matrix and carbon-enrichment in the retained austenite. The softening of the martensitic matrix caused by carbon-depletion markedly enhances its deformation ability and raises the ductility of Q–P–T steels. During deformation dislocation absorption by retained austenite (DARA) effect will occur, that is, the dislocations in martensitic matrix will move into nearby retained austenite through the martensite-austenite interface and be absorbed by the retained austenite. This second softening of the martensitic matrix also enhances its deformation ability and effectively raises the ductility. The effect of DARA on ductility during deformation is more effective than the transformation-induced plasticity (TRIP) effect caused by martensitic transformation of retained austenite, because during the TRIP effect the twin-type martensite produced by strain-induced martensitic transformation of retained austenite is very detrimental to ductility.
- 5 March 2019
- Published by Taylor & Francis in Heat Treatment and Surface Engineering
- Vol. 1 (1-2) , 2-10
Open AccessThe twice softening of martensitic matrix in Q–P–T steels and its effect on ductility
When a Si-containing steel is subjected to quenching-partitioning-tempering (Q–P–T) process, it will become a martensitic steel with considerable volume of retained austenite, which is attributed to the partitioning of carbon from martensite to retained austenite leading to carbon-depletion in martensitic matrix and carbon-enrichment in the retained austenite. The softening of the martensitic matrix caused by carbon-depletion markedly enhances its deformation ability and raises the ductility of Q–P–T steels. During deformation dislocation absorption by retained austenite (DARA) effect will occur, that is, the dislocations in martensitic matrix will move into nearby retained austenite through the martensite-austenite interface and be absorbed by the retained austenite. This second softening of the martensitic matrix also enhances its deformation ability and effectively raises the ductility. The effect of DARA on ductility during deformation is more effective than the transformation-induced plasticity (TRIP) effect caused by martensitic transformation of retained austenite, because during the TRIP effect the twin-type martensite produced by strain-induced martensitic transformation of retained austenite is very detrimental to ductility.