Sanha Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sanha Kim has a total of 202 co-authors. Here are the top co-authors by number of shared publications:
- Sukkyung Kang
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
10 shared publications - Anastasios John Hart
Massachusetts Institute of Technology
9 shared publications Hyun Jun Ryu
8 shared publications- Seong Jae Kim
Mechanical Engineering Research Institute Korea Advanced Institute of Science and Technology (KAIST) Daejeon Republic of Korea
7 shared publications Dong Geun Kim
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 34141, Republic of Korea
6 shared publicationsHyeongmin Je
6 shared publications
Latest Publications
- 22 September 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (18) , 9028-9041
Data-free physics-informed inverse programming of bistable kirigami energy landscapes
Data-free physics-informed inverse programming enables direct control of energy landscapes and deformation in bistable kirigami metamaterials.
- 22 September 2026
- Published by Royal Society of Chemistry (RSC) in Materials Horizons
- Vol. 13 (18) , 9028-9041
Data-free physics-informed inverse programming of bistable kirigami energy landscapes
Data-free physics-informed inverse programming enables direct control of energy landscapes and deformation in bistable kirigami metamaterials.
- Open Access
- 4 August 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (55) , e74470
Scalable Synthesis of 3D Hierarchical MoS 2 as a Durable, High‐Charge‐Retention Friction Layer for the Facile Fabrication of High‐Power Triboelectric Nanogenerators
Given the increasing demand for sustainable energy and self‐powered devices, energy‐harvesting technologies, such as triboelectric nanogenerators (TENGs), are drawing attention. To address the short charge retention in conventional polymer materials, 2D materials with high surface areas and intrinsic charge‐trapping capabilities, such as MoS 2 , are being utilized as friction layers in TENGs. However, their power generation is too low for practical applications owing to their atomically thin nature, limiting their use as fillers in polymer‐based systems. We report a 2D‐material‐based high‐power TENG using 3D hierarchical MoS 2 (3DH‐MoS 2 ) as a primary friction material. The 3DH‐MoS 2 is synthesized via low‐temperature metal–organic chemical vapor deposition, enabling the direct growth of a uniform, large‐area, 3D‐nanostructured friction layer on a polymer substrate without additional processes. This 3D nanostructure increases the amount of charge‐trapping sites and significantly enhances the durability of the device. The 4 × 4 cm 2 3DH‐MoS 2 ‐based TENG produces a maximum output voltage of 320.1 V and a power density of 0.841 mW cm −2 , proving it can effectively power light‐emitting diodes and a calculator, maintaining its performance over 10 000 cycles. In addition, the device can generate electricity from gas and water flow and human motion, highlighting the potential and versatility of 2D‐material‐based energy‐harvesting systems.
- 4 August 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (55) , e74470
Open AccessScalable Synthesis of 3D Hierarchical MoS 2 as a Durable, High‐Charge‐Retention Friction Layer for the Facile Fabrication of High‐Power Triboelectric Nanogenerators
Given the increasing demand for sustainable energy and self‐powered devices, energy‐harvesting technologies, such as triboelectric nanogenerators (TENGs), are drawing attention. To address the short charge retention in conventional polymer materials, 2D materials with high surface areas and intrinsic charge‐trapping capabilities, such as MoS 2 , are being utilized as friction layers in TENGs. However, their power generation is too low for practical applications owing to their atomically thin nature, limiting their use as fillers in polymer‐based systems. We report a 2D‐material‐based high‐power TENG using 3D hierarchical MoS 2 (3DH‐MoS 2 ) as a primary friction material. The 3DH‐MoS 2 is synthesized via low‐temperature metal–organic chemical vapor deposition, enabling the direct growth of a uniform, large‐area, 3D‐nanostructured friction layer on a polymer substrate without additional processes. This 3D nanostructure increases the amount of charge‐trapping sites and significantly enhances the durability of the device. The 4 × 4 cm 2 3DH‐MoS 2 ‐based TENG produces a maximum output voltage of 320.1 V and a power density of 0.841 mW cm −2 , proving it can effectively power light‐emitting diodes and a calculator, maintaining its performance over 10 000 cycles. In addition, the device can generate electricity from gas and water flow and human motion, highlighting the potential and versatility of 2D‐material‐based energy‐harvesting systems.
- 21 July 2026
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 327
Engineering and mechanics of low-adhesion surfaces with vertically-aligned carbon nanotubes
- 21 July 2026
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 327
Engineering and mechanics of low-adhesion surfaces with vertically-aligned carbon nanotubes
- 1 July 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (7)
Asymmetric-beam steady-state thermoreflectance for three-dimensional anisotropic thermal conductivity measurements.
The accurate measurement of anisotropic thermal conductivity is essential for understanding heat transport and enabling practical applications, such as thermal management, yet reliable characterization remains challenging, particularly for in-plane anisotropic materials with low thermal conductivity. Here, we present an asymmetric-beam steady-state thermoreflectance (AB-SSTR) technique that integrates an elliptical laser beam into a conventional steady-state thermoreflectance framework. By controlling the beam aspect ratio and spot size, the elliptical geometry modifies the thermoreflectance sensitivity to thermal conductivity along the three principal axes. Thermal conductivities are extracted by combining two measurements with orthogonally exchanged major and minor beam axes and analyzing the resulting response using a steady-state three-dimensional heat conduction model. We validate the approach using various samples, and the measured values are in good agreement with the literature. These results establish AB-SSTR as a robust, non-contact method for probing anisotropic heat transport in diverse materials.
- 1 July 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (7)
Asymmetric-beam steady-state thermoreflectance for three-dimensional anisotropic thermal conductivity measurements.
The accurate measurement of anisotropic thermal conductivity is essential for understanding heat transport and enabling practical applications, such as thermal management, yet reliable characterization remains challenging, particularly for in-plane anisotropic materials with low thermal conductivity. Here, we present an asymmetric-beam steady-state thermoreflectance (AB-SSTR) technique that integrates an elliptical laser beam into a conventional steady-state thermoreflectance framework. By controlling the beam aspect ratio and spot size, the elliptical geometry modifies the thermoreflectance sensitivity to thermal conductivity along the three principal axes. Thermal conductivities are extracted by combining two measurements with orthogonally exchanged major and minor beam axes and analyzing the resulting response using a steady-state three-dimensional heat conduction model. We validate the approach using various samples, and the measured values are in good agreement with the literature. These results establish AB-SSTR as a robust, non-contact method for probing anisotropic heat transport in diverse materials.
- 23 June 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 127
Material extrusion additive manufacturing of high iron particle loaded polymer filaments for axial flux motor stator
- 23 June 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 127
Material extrusion additive manufacturing of high iron particle loaded polymer filaments for axial flux motor stator
- 7 May 2026
- Published by Elsevier in CIRP Annals
- Vol. 75 (1) , 715-719
Load-independent low friction of fouling release coating in shipyard
- 7 May 2026
- Published by Elsevier in CIRP Annals
- Vol. 75 (1) , 715-719
Load-independent low friction of fouling release coating in shipyard
- 6 May 2026
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 11 (5) , 3889-3899
Thin-Film Eddy Current Sensors for Proximity Detection in Smart Capillary Pick-and-Place
The eddy current sensor is a representative nondestructive sensing technique that enables sensitive interrogation of the conductive object surface in close proximity. Here, we propose an eddy current-based proximity detection strategy using a micropatterned inductor fabricated on a thin-film substrate (25 μm thickness) for integration as a smart, in situ inspection modality in advanced capillary pick-and-place systems. Notably, the eddy current sensing mechanism exhibited small sensitivity to liquids, allowing successful proximity detection during capillary pick-and-place operations. Our new suggested sensor consists of a copper inductor micro-fabricated on one side of a thin polyimide film surface, while the other side is roughened in nanoscale by argon plasma treatment. This new design offers several advantages: (1) enhanced eddy current induction efficiency enabled by thickness reduction, achieving an inductance change of up to 54.7% upon copper contact; and (2) facile release of lightweight objects due to reduced surface adhesion during the pick-and-place process. We verified the electrical and eddy current sensing characteristics of the micropatterned inductors via experiments and finite element simulations. We then further explored the in situ sensing capability during capillary pick-and-place operation by measuring the impedance change over time. The decreased adhesion of the plasma-treated polyimide surface was verified by atomic force microscopy and supported by an analytical model. We envision that this approach provides a promising strategy for advanced manufacturing applications requiring high reliability and nondestructive in situ monitoring during pick-and-place operations.
- 6 May 2026
- Published by American Chemical Society (ACS) in ACS Sensors
- Vol. 11 (5) , 3889-3899
Thin-Film Eddy Current Sensors for Proximity Detection in Smart Capillary Pick-and-Place
The eddy current sensor is a representative nondestructive sensing technique that enables sensitive interrogation of the conductive object surface in close proximity. Here, we propose an eddy current-based proximity detection strategy using a micropatterned inductor fabricated on a thin-film substrate (25 μm thickness) for integration as a smart, in situ inspection modality in advanced capillary pick-and-place systems. Notably, the eddy current sensing mechanism exhibited small sensitivity to liquids, allowing successful proximity detection during capillary pick-and-place operations. Our new suggested sensor consists of a copper inductor micro-fabricated on one side of a thin polyimide film surface, while the other side is roughened in nanoscale by argon plasma treatment. This new design offers several advantages: (1) enhanced eddy current induction efficiency enabled by thickness reduction, achieving an inductance change of up to 54.7% upon copper contact; and (2) facile release of lightweight objects due to reduced surface adhesion during the pick-and-place process. We verified the electrical and eddy current sensing characteristics of the micropatterned inductors via experiments and finite element simulations. We then further explored the in situ sensing capability during capillary pick-and-place operation by measuring the impedance change over time. The decreased adhesion of the plasma-treated polyimide surface was verified by atomic force microscopy and supported by an analytical model. We envision that this approach provides a promising strategy for advanced manufacturing applications requiring high reliability and nondestructive in situ monitoring during pick-and-place operations.
- Open Access
- 20 March 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale Horizons
- Vol. 11 (6) , 1578-1589
Surface-modified anode current collectors via lithiophilic zinc-based bimetallic co-electrodeposition for lithium–metal batteries
Lithium–metal batteries (LMBs) are considered promising next-generation energy storage systems due to their extremely high theoretical capacity and low electrochemical potential. However, their practical application is limited by the formation of lithium dendrites and poor interfacial stability during cycling. In this study, we propose a scalable CuZn bimetallic co-electrodeposition strategy for modification of current collector surfaces that effectively suppress dendritic growth and enhance cyclic reversibility. Zinc, a lithiophilic metal, was selected as a surface modifier owing to its favorable alloying characteristics with lithium. Substantial differences in standard reduction potentials exist between Cu and Zn, yet we successfully deposited Cu and Zn simultaneously by introducing potassium pyrophosphate into the electrolyte, which modulates the ion activity through complexation. The CuZn morphology was further tuned from flat films to branched nanostructures by controlling the electrolyte composition and deposition voltage. Post-deposition annealing facilitated interdiffusion at the Cu/CuZn interface, resulting in the formation of a recrystallized Cu0.75Zn0.25 alloy and improved mechanical bonding. Compared to bare Cu foils, the heat-treated CuZn current collectors extended the cell lifespan by 44.3% and the nanostructured CuZn further improved it by 87.2%. Electrochemical impedance spectroscopy and lithium nucleation overpotential analysis confirmed reduced interfacial resistance and improved uniformity in Li plating behavior. This work offers a practical and scalable approach for surface modification of anode current collectors for stable and long-life LMBs.
- 20 March 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale Horizons
- Vol. 11 (6) , 1578-1589
Open AccessSurface-modified anode current collectors via lithiophilic zinc-based bimetallic co-electrodeposition for lithium–metal batteries
Lithium–metal batteries (LMBs) are considered promising next-generation energy storage systems due to their extremely high theoretical capacity and low electrochemical potential. However, their practical application is limited by the formation of lithium dendrites and poor interfacial stability during cycling. In this study, we propose a scalable CuZn bimetallic co-electrodeposition strategy for modification of current collector surfaces that effectively suppress dendritic growth and enhance cyclic reversibility. Zinc, a lithiophilic metal, was selected as a surface modifier owing to its favorable alloying characteristics with lithium. Substantial differences in standard reduction potentials exist between Cu and Zn, yet we successfully deposited Cu and Zn simultaneously by introducing potassium pyrophosphate into the electrolyte, which modulates the ion activity through complexation. The CuZn morphology was further tuned from flat films to branched nanostructures by controlling the electrolyte composition and deposition voltage. Post-deposition annealing facilitated interdiffusion at the Cu/CuZn interface, resulting in the formation of a recrystallized Cu0.75Zn0.25 alloy and improved mechanical bonding. Compared to bare Cu foils, the heat-treated CuZn current collectors extended the cell lifespan by 44.3% and the nanostructured CuZn further improved it by 87.2%. Electrochemical impedance spectroscopy and lithium nucleation overpotential analysis confirmed reduced interfacial resistance and improved uniformity in Li plating behavior. This work offers a practical and scalable approach for surface modification of anode current collectors for stable and long-life LMBs.
- Top Cited PapersOpen Access
- 14 January 2026
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 13 (5) , 1-40
Challenges and Innovations in Chemical Mechanical Polishing in the More-than-Moore Era
As the More-than-Moore (MtM) paradigm reshapes semiconductor manufacturing toward functional integration, material diversity, and high-precision three-dimensional (3D) architectures, chemical mechanical polishing (CMP) has evolved from a planarization step into a critical enabler of heterogeneous integration. This review comprehensively examines the key challenges and technological innovations driving CMP in the MtM era. In front-end-of-line (FEOL) processes, high selectivity among diverse materials should be ensured while suppressing defects. In back-end-of-line (BEOL) and advanced packaging, CMP is required to deliver sub-nanometer flatness across complex multilayer and hybrid bonding structures. The emergence of wide-bandgap materials such as SiC and GaN introduces additional demands for chemically enhanced and hybrid CMP techniques to overcome their extreme hardness and chemical inertness. Furthermore, recent advancements in artificial intelligence (AI)-driven process prediction, in-situ sensing, and eco-friendly consumables are accelerating CMP’s transformation into a data-informed, sustainable manufacturing platform. This review redefines CMP as a foundational technology for next-generation integration and outlines its future trajectory in advanced semiconductor fabrication.
- 14 January 2026
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 13 (5) , 1-40
Top Cited PapersOpen AccessChallenges and Innovations in Chemical Mechanical Polishing in the More-than-Moore Era
As the More-than-Moore (MtM) paradigm reshapes semiconductor manufacturing toward functional integration, material diversity, and high-precision three-dimensional (3D) architectures, chemical mechanical polishing (CMP) has evolved from a planarization step into a critical enabler of heterogeneous integration. This review comprehensively examines the key challenges and technological innovations driving CMP in the MtM era. In front-end-of-line (FEOL) processes, high selectivity among diverse materials should be ensured while suppressing defects. In back-end-of-line (BEOL) and advanced packaging, CMP is required to deliver sub-nanometer flatness across complex multilayer and hybrid bonding structures. The emergence of wide-bandgap materials such as SiC and GaN introduces additional demands for chemically enhanced and hybrid CMP techniques to overcome their extreme hardness and chemical inertness. Furthermore, recent advancements in artificial intelligence (AI)-driven process prediction, in-situ sensing, and eco-friendly consumables are accelerating CMP’s transformation into a data-informed, sustainable manufacturing platform. This review redefines CMP as a foundational technology for next-generation integration and outlines its future trajectory in advanced semiconductor fabrication.