Thomas A. Fox
Thomas A. Fox has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Arvind Pawan Ravikumar
The University of Texas at Austin
3 shared publications Chris H Hugenholtz
Department of Geography, University of Calgary, 2500 University Dr NW, Calgary, Alberta, T2N 1N4, CANADA
3 shared publicationsMozhou Gao
Department of Geography, University of Calgary, 2500 University Dr NW, Calgary, Alberta, T2N 1N4, CANADA
3 shared publicationsThomas E Barchyn
Department of Geography, University of Calgary, 2500 University Dr NW, Calgary, Alberta, T2N 1N4, CANADA
3 shared publications- Alex MacGregor
Qube Technologies
2 shared publications - Brendan Moorhouse
Highwood Emissions Management
2 shared publications
Latest Publications
- 20 April 2023
- Published by Society of Petroleum Engineers (SPE) in SPE Production & Operations
- Vol. 38 (03) , 383-390
Continuous Methane Monitoring: Equivalency Evaluation of Regulator-Approved Alternative Leak Detection and Repair Program in Alberta, Canada
Summary: Diverse methods have emerged for methane leak detection and repair (LDAR), alongside a growing interest in continuous monitoring (CM). Novel LDAR programs must demonstrate equivalent (or better) emissions reductions compared to conventional handheld methods to be approved by regulators and trusted by industry. We apply and test a widely accepted equivalency framework and report on a regulatory approved alternative LDAR pilot program to evaluate the performance of CM relative to conventional LDAR. The framework, which has not been formally tested to date, relies on a combination of controlled release testing, simulation modeling, and field piloting. First, controlled release testing at known emission rates is used to establish probability of detection functions and other performance metrics for the CM device. Performance metrics are then used to build a CM module in LDAR Simulator (LDAR-Sim), an open-access modeling framework. Finally, CM devices are deployed as part of a field pilot. Controlled release testing results and dispersion modeling suggest that the CM devices can reliably detect (i.e., 90% detection probability or greater) a rate of 1 kg/h (~54 scf/hr) from distances of 75–100 m with no false positive detections. A set of work practices were established using the LDAR-Sim framework. The CM program requires close-range follow-up for any detection event and is estimated by LDAR-Sim to reduce aggregate annual fugitive methane emissions by 91.8% relative to the baseline, doubling the reductions anticipated from a conventional regulatory program. For the pilot, 52 devices are deployed across 16 facilities with Enhance Energy. All devices are positioned within 100 m of monitored assets. Each time devices record a detection event, which is defined as a sustained anomaly three standard deviations above a moving average background concentration for 24 hours, 7 days, or 60 days, the operator performs a close-range follow-up inspection. Preliminary results show that the CM devices can detect leaks and that follow-up protocols are effective at immediately finding leaks and avoiding false positives. Confirmed detections include fugitive emissions such as a tank thief hatch leak and vented emissions including high-bleed pneumatics. Both types of emissions were confirmed as repaired or improved by CM. These results indicate that repairing leaks more expeditiously through faster detection can reduce emissions by up to 90%.
- 20 April 2023
- Published by Society of Petroleum Engineers (SPE) in SPE Production & Operations
- Vol. 38 (03) , 383-390
Continuous Methane Monitoring: Equivalency Evaluation of Regulator-Approved Alternative Leak Detection and Repair Program in Alberta, Canada
Summary: Diverse methods have emerged for methane leak detection and repair (LDAR), alongside a growing interest in continuous monitoring (CM). Novel LDAR programs must demonstrate equivalent (or better) emissions reductions compared to conventional handheld methods to be approved by regulators and trusted by industry. We apply and test a widely accepted equivalency framework and report on a regulatory approved alternative LDAR pilot program to evaluate the performance of CM relative to conventional LDAR. The framework, which has not been formally tested to date, relies on a combination of controlled release testing, simulation modeling, and field piloting. First, controlled release testing at known emission rates is used to establish probability of detection functions and other performance metrics for the CM device. Performance metrics are then used to build a CM module in LDAR Simulator (LDAR-Sim), an open-access modeling framework. Finally, CM devices are deployed as part of a field pilot. Controlled release testing results and dispersion modeling suggest that the CM devices can reliably detect (i.e., 90% detection probability or greater) a rate of 1 kg/h (~54 scf/hr) from distances of 75–100 m with no false positive detections. A set of work practices were established using the LDAR-Sim framework. The CM program requires close-range follow-up for any detection event and is estimated by LDAR-Sim to reduce aggregate annual fugitive methane emissions by 91.8% relative to the baseline, doubling the reductions anticipated from a conventional regulatory program. For the pilot, 52 devices are deployed across 16 facilities with Enhance Energy. All devices are positioned within 100 m of monitored assets. Each time devices record a detection event, which is defined as a sustained anomaly three standard deviations above a moving average background concentration for 24 hours, 7 days, or 60 days, the operator performs a close-range follow-up inspection. Preliminary results show that the CM devices can detect leaks and that follow-up protocols are effective at immediately finding leaks and avoiding false positives. Confirmed detections include fugitive emissions such as a tank thief hatch leak and vented emissions including high-bleed pneumatics. Both types of emissions were confirmed as repaired or improved by CM. These results indicate that repairing leaks more expeditiously through faster detection can reduce emissions by up to 90%.
- 26 September 2022
- Published by Society of Petroleum Engineers (SPE)
Continuous Methane Measurement: Equivalency Evaluation of Regulator-Approved Alternative Leak Detection and Repair Program in Alberta, Canada
Diverse methods have emerged for methane Leak Detection and Repair (LDAR), alongside a growing interest in continuous measurement (CM). Novel LDAR programs must demonstrate equivalent (or better) emissions reductions compared to conventional handheld methods to be approved by regulators and trusted by industry. We apply and test a widely accepted equivalency framework and report on a regulatory approved alternative LDAR pilot program to evaluate the performance of CM relative to conventional LDAR. The framework, which has not been formally tested to date, relies on a combination of controlled release testing, simulation modeling, and field piloting. First, controlled release testing at known emission rates is used to establish probability of detection functions and other performance metrics for the CM device. Performance metrics are then used to build a CM module in LDAR-Sim, an open-access modeling framework. Finally, CM devices are deployed as part of a field pilot. Controlled release testing results and dispersion modeling suggest that the CM devices can reliably detect (i.e., 90% detection probability or greater) a rate of 1 kg/h (~54 scfh) from distances of 75 to 100 meters with no false positive detections. A set of work practices were established using the LDAR-Sim framework. The CM program requires close-range follow-up for any detection event and is estimated by LDAR-Sim to reduce aggregate annual fugitive methane emissions by 91.8% relative to the baseline, doubling the reductions anticipated from a conventional regulatory program. For the pilot, 52 devices are deployed across 16 facilities with Enhance Energy. All devices are positioned within 100 m of monitored assets. Each time devices record a detection event, which is defined as a sustained anomaly three standard deviations above a moving average background concentration for 24 hours, 7 days or 60 days, the operator performs a close-range follow-up inspection. Preliminary results show that the CM devices can detect leaks and that follow-up protocols are effective at immediately finding leaks and avoiding false positives. Confirmed detections include fugitive emissions such as a tank thief hatch leak and vented emissions including high bleed pneumatics. Both types of emissions were confirmed as repaired or improved by CM. These results indicate that repairing leaks more expeditiously through faster detection can reduce emissions by up to 90%.
- 26 September 2022
- Published by Society of Petroleum Engineers (SPE)
Continuous Methane Measurement: Equivalency Evaluation of Regulator-Approved Alternative Leak Detection and Repair Program in Alberta, Canada
Diverse methods have emerged for methane Leak Detection and Repair (LDAR), alongside a growing interest in continuous measurement (CM). Novel LDAR programs must demonstrate equivalent (or better) emissions reductions compared to conventional handheld methods to be approved by regulators and trusted by industry. We apply and test a widely accepted equivalency framework and report on a regulatory approved alternative LDAR pilot program to evaluate the performance of CM relative to conventional LDAR. The framework, which has not been formally tested to date, relies on a combination of controlled release testing, simulation modeling, and field piloting. First, controlled release testing at known emission rates is used to establish probability of detection functions and other performance metrics for the CM device. Performance metrics are then used to build a CM module in LDAR-Sim, an open-access modeling framework. Finally, CM devices are deployed as part of a field pilot. Controlled release testing results and dispersion modeling suggest that the CM devices can reliably detect (i.e., 90% detection probability or greater) a rate of 1 kg/h (~54 scfh) from distances of 75 to 100 meters with no false positive detections. A set of work practices were established using the LDAR-Sim framework. The CM program requires close-range follow-up for any detection event and is estimated by LDAR-Sim to reduce aggregate annual fugitive methane emissions by 91.8% relative to the baseline, doubling the reductions anticipated from a conventional regulatory program. For the pilot, 52 devices are deployed across 16 facilities with Enhance Energy. All devices are positioned within 100 m of monitored assets. Each time devices record a detection event, which is defined as a sustained anomaly three standard deviations above a moving average background concentration for 24 hours, 7 days or 60 days, the operator performs a close-range follow-up inspection. Preliminary results show that the CM devices can detect leaks and that follow-up protocols are effective at immediately finding leaks and avoiding false positives. Confirmed detections include fugitive emissions such as a tank thief hatch leak and vented emissions including high bleed pneumatics. Both types of emissions were confirmed as repaired or improved by CM. These results indicate that repairing leaks more expeditiously through faster detection can reduce emissions by up to 90%.
- Open Access
- 1 June 2021
- Published by IOP Publishing in Environmental Research Letters
- Vol. 16 (6) , 064077
Can new mobile technologies enable fugitive methane reductions from the oil and gas industry?
New mobile platforms such as vehicles, drones, aircraft, and satellites have emerged to help identify and reduce fugitive methane emissions from the oil and gas sector. When deployed as part of leak detection and repair (LDAR) programs, most of these technologies use multi-visit LDAR (MVL), which consists of four steps: (a) rapidly screen all facilities, (b) triage by emission rate, (c) follow-up with close-range methods at the highest-emitting sites, and (d) conduct repairs. The proposed value of MVL is to identify large leaks soon after they arise. Whether MVL offers an improvement over traditional single-visit LDAR (SVL), which relies on undirected close-range surveys, remains poorly understood. We use the Leak Detection and Repair Simulator (LDAR-Sim) to examine the performance and cost-effectiveness of MVL relative to SVL. Results suggest that facility-scale MVL programs can achieve fugitive emission reductions equivalent to SVL, but that improved cost-effectiveness is not guaranteed. Under a best-case scenario, we find that screening must cost < USD 100 per site for MVL to achieve 30% cost reductions relative to SVL. In scenarios with non-target vented emissions and screening quantification uncertainty, triaging errors force excessive close-range follow-up to achieve emissions reduction equivalence. The viability of MVL as a cost-effective alternative to SVL for reducing fugitive methane emissions hinges on accurate triaging after the screening phase.
- 1 June 2021
- Published by IOP Publishing in Environmental Research Letters
- Vol. 16 (6) , 064077
Open AccessCan new mobile technologies enable fugitive methane reductions from the oil and gas industry?
New mobile platforms such as vehicles, drones, aircraft, and satellites have emerged to help identify and reduce fugitive methane emissions from the oil and gas sector. When deployed as part of leak detection and repair (LDAR) programs, most of these technologies use multi-visit LDAR (MVL), which consists of four steps: (a) rapidly screen all facilities, (b) triage by emission rate, (c) follow-up with close-range methods at the highest-emitting sites, and (d) conduct repairs. The proposed value of MVL is to identify large leaks soon after they arise. Whether MVL offers an improvement over traditional single-visit LDAR (SVL), which relies on undirected close-range surveys, remains poorly understood. We use the Leak Detection and Repair Simulator (LDAR-Sim) to examine the performance and cost-effectiveness of MVL relative to SVL. Results suggest that facility-scale MVL programs can achieve fugitive emission reductions equivalent to SVL, but that improved cost-effectiveness is not guaranteed. Under a best-case scenario, we find that screening must cost < USD 100 per site for MVL to achieve 30% cost reductions relative to SVL. In scenarios with non-target vented emissions and screening quantification uncertainty, triaging errors force excessive close-range follow-up to achieve emissions reduction equivalence. The viability of MVL as a cost-effective alternative to SVL for reducing fugitive methane emissions hinges on accurate triaging after the screening phase.
- Open Access
- 1 February 2021
- Published by Elsevier in Journal of Cleaner Production
- Vol. 282
An agent-based model for estimating emissions reduction equivalence among leak detection and repair programs
- 1 February 2021
- Published by Elsevier in Journal of Cleaner Production
- Vol. 282
Open AccessAn agent-based model for estimating emissions reduction equivalence among leak detection and repair programs
- Open Access
- 23 June 2020
- Published by California Digital Library (CDL) in EarthArXiv
An agent-based model for estimating emissions reduction equivalence among leak detection and repair programs
- 23 June 2020
- Published by California Digital Library (CDL) in EarthArXiv
Open AccessAn agent-based model for estimating emissions reduction equivalence among leak detection and repair programs
- Open Access
- 31 May 2019
- Published by IOP Publishing in Environmental Research Letters
- Vol. 14 (6) , 069601
Erratum: A review of close-range and screening technologies for mitigating fugitive methane emissions in upstream oil and gas (2019 Environ. Res. Lett. 14 053002)
- 31 May 2019
- Published by IOP Publishing in Environmental Research Letters
- Vol. 14 (6) , 069601
Open AccessErratum: A review of close-range and screening technologies for mitigating fugitive methane emissions in upstream oil and gas (2019 Environ. Res. Lett. 14 053002)
- Top Cited PapersOpen Access
- 26 April 2019
- Published by IOP Publishing in Environmental Research Letters
- Vol. 14 (5) , 053002
A review of close-range and screening technologies for mitigating fugitive methane emissions in upstream oil and gas
Fugitive methane emissions from the oil and gas industry are targeted using leak detection and repair (LDAR) programs. Until recently, only a limited number of measurement standards have been permitted by most regulators, with emphasis on close-range methods (e.g. Method-21, optical gas imaging). Although close-range methods are essential for source identification, they can be labor-intensive. To improve LDAR efficiency, there has been a policy shift in Canada and the United States towards incorporating alternative technologies. However, the suitability of these technologies for LDAR remains unclear. In this paper, we systematically review and compare six technology classes for use in LDAR: handheld instruments, fixed sensors, mobile ground labs (MGLs), unmanned aerial vehicles (UAVs), aircraft, and satellites. These technologies encompass broad spatial and temporal scales of measurement. Minimum detection limits for technology classes range from −1 for Method 21 instruments to 7.1 × 106 g h−1 for the GOSAT satellite, and uncertainties are poorly constrained. To leverage the diverse capabilities of these technologies, we introduce a hybrid screening-confirmation approach to LDAR called a comprehensive monitoring program. Here, a screening technology is used to rapidly tag high-emitting sites to direct close-range source identification. Currently, fixed sensors, MGLs, UAVs, and aircraft could be used as screening technologies, but their performances must be evaluated under a range of environmental and operational conditions to better constrain detection effectiveness. Methane-sensing satellites are improving rapidly and may soon be ready for facility-scale screening. We conclude with a speculative discussion of the future of LDAR, touching on integration, analytics, incentivization, and regulatory pathways.
- 26 April 2019
- Published by IOP Publishing in Environmental Research Letters
- Vol. 14 (5) , 053002
Top Cited PapersOpen AccessA review of close-range and screening technologies for mitigating fugitive methane emissions in upstream oil and gas
Fugitive methane emissions from the oil and gas industry are targeted using leak detection and repair (LDAR) programs. Until recently, only a limited number of measurement standards have been permitted by most regulators, with emphasis on close-range methods (e.g. Method-21, optical gas imaging). Although close-range methods are essential for source identification, they can be labor-intensive. To improve LDAR efficiency, there has been a policy shift in Canada and the United States towards incorporating alternative technologies. However, the suitability of these technologies for LDAR remains unclear. In this paper, we systematically review and compare six technology classes for use in LDAR: handheld instruments, fixed sensors, mobile ground labs (MGLs), unmanned aerial vehicles (UAVs), aircraft, and satellites. These technologies encompass broad spatial and temporal scales of measurement. Minimum detection limits for technology classes range from −1 for Method 21 instruments to 7.1 × 106 g h−1 for the GOSAT satellite, and uncertainties are poorly constrained. To leverage the diverse capabilities of these technologies, we introduce a hybrid screening-confirmation approach to LDAR called a comprehensive monitoring program. Here, a screening technology is used to rapidly tag high-emitting sites to direct close-range source identification. Currently, fixed sensors, MGLs, UAVs, and aircraft could be used as screening technologies, but their performances must be evaluated under a range of environmental and operational conditions to better constrain detection effectiveness. Methane-sensing satellites are improving rapidly and may soon be ready for facility-scale screening. We conclude with a speculative discussion of the future of LDAR, touching on integration, analytics, incentivization, and regulatory pathways.
- Open Access
- 1 January 2019
- Published by University of California Press in Elementa: Science of the Anthropocene
- Vol. 7 (1)
Plume detection modeling of a drone-based natural gas leak detection system
Interest has grown in using new screening technologies such as drones to search for methane leaks in hydrocarbon production infrastructure. Screening technologies may be less expensive and faster than traditional methods. However, including new technologies in emissions monitoring programs requires an accurate understanding of what leaks a system will detect and the resultant emissions mitigation. Here we examine source detection of a drone-based system with controlled releases. We examine different detection algorithm parameters to understand trade-offs between false positive rate and detection probability. Leak detection was poor under all conditions with an average detection probability of 0.21. Detection probability was not affected by emission rate, suggesting similar systems may commonly miss large leaks. Detection was best in moderate wind speeds and at 750–2000 m downwind from the source where the plume had diffused vertically above the minimum flight level of 40–50 m. Predicted concentration enhancement from a Gaussian plume model was a reasonable predictor of detection within the test suite. Enabling lower flight elevations may increase detection probability. Overall, the experiments suggest that controlled releases are useful and necessary to provide an understanding of detection probability of screening technologies for regulatory and deployment purposes, and the testing must be representative to support broad application.
- 1 January 2019
- Published by University of California Press in Elementa: Science of the Anthropocene
- Vol. 7 (1)
Open AccessPlume detection modeling of a drone-based natural gas leak detection system
Interest has grown in using new screening technologies such as drones to search for methane leaks in hydrocarbon production infrastructure. Screening technologies may be less expensive and faster than traditional methods. However, including new technologies in emissions monitoring programs requires an accurate understanding of what leaks a system will detect and the resultant emissions mitigation. Here we examine source detection of a drone-based system with controlled releases. We examine different detection algorithm parameters to understand trade-offs between false positive rate and detection probability. Leak detection was poor under all conditions with an average detection probability of 0.21. Detection probability was not affected by emission rate, suggesting similar systems may commonly miss large leaks. Detection was best in moderate wind speeds and at 750–2000 m downwind from the source where the plume had diffused vertically above the minimum flight level of 40–50 m. Predicted concentration enhancement from a Gaussian plume model was a reasonable predictor of detection within the test suite. Enabling lower flight elevations may increase detection probability. Overall, the experiments suggest that controlled releases are useful and necessary to provide an understanding of detection probability of screening technologies for regulatory and deployment purposes, and the testing must be representative to support broad application.
- Open Access
- 1 January 2019
- Published by University of California Press in Elementa: Science of the Anthropocene
- Vol. 7
A methane emissions reduction equivalence framework for alternative leak detection and repair programs
Fugitive methane emissions from the oil and gas sector are typically addressed through periodic leak detection and repair surveys. These surveys, conducted manually using handheld leak detection technologies, are time-consuming. To improve the speed and cost-effectiveness of leak detection, technology developers are introducing innovative solutions using mobile platforms, close-range portable systems, and permanent installations. Many of these new approaches promise faster, cheaper, or more effective leak detection than conventional methods. However, ensuring mitigation targets are achieved requires demonstrating that alternative approaches are at least as effective in reducing emissions as current approaches – a concept known as emissions reduction equivalence. Here, we propose a five-stage framework for demonstrating equivalence that combines controlled testing, simulation modeling, and field trials. The framework was developed in consultation with operators, regulators, academics, solution providers, consultants, and non-profit groups from Canada and the U.S. We present the equivalence framework and discuss challenges to implementation.
- 1 January 2019
- Published by University of California Press in Elementa: Science of the Anthropocene
- Vol. 7
Open AccessA methane emissions reduction equivalence framework for alternative leak detection and repair programs
Fugitive methane emissions from the oil and gas sector are typically addressed through periodic leak detection and repair surveys. These surveys, conducted manually using handheld leak detection technologies, are time-consuming. To improve the speed and cost-effectiveness of leak detection, technology developers are introducing innovative solutions using mobile platforms, close-range portable systems, and permanent installations. Many of these new approaches promise faster, cheaper, or more effective leak detection than conventional methods. However, ensuring mitigation targets are achieved requires demonstrating that alternative approaches are at least as effective in reducing emissions as current approaches – a concept known as emissions reduction equivalence. Here, we propose a five-stage framework for demonstrating equivalence that combines controlled testing, simulation modeling, and field trials. The framework was developed in consultation with operators, regulators, academics, solution providers, consultants, and non-profit groups from Canada and the U.S. We present the equivalence framework and discuss challenges to implementation.
- 1 May 1990
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 34 (1) , 27-44
Wind effects on structural intersections
- 1 May 1990
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 34 (1) , 27-44
Wind effects on structural intersections