ASAnne-Christine Scherzer

Anne-Christine Scherzer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anne-Christine Scherzer has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    PEMFC Performance Modeling Framework: Analyzing Pt Particle Size Distribution and Carbon Support Structure Impact

    by Dietmar Gerteisen, Patrick Schneider, Anne-Christine Scherzer

    A cathode catalyst layer model framework that accounts for the position of the platinum particles on the carbon support structure is proposed. Combining a discrete platinum particle size distribution (PSD) with the binary classification of whether the platinum particle is decorated on the support surface (Pt outer ) or buried inside the pore structure (Pt inner ) allows the differentiation of distinct loss mechanisms. Additional mass transport and proton accessibility issues are modelled for Pt inner due to the extended diffusion path and worsened proton conduction inside the ionomer-free primary pores of the carbon support. Pt outer particles suffer from the adsorption of sulphonic acid groups (ionomer poisoning) and the densification of ionomer thin film that builds a compact layer above the outer Pt particle. The influence of carbon support type such as high and low surface area carbon on the cell performance is simulated and discussed for different scenarios. A parameter study is conducted that gives insight into the complex interaction between the contribution of current generation obtained from Pt inner and those from Pt outer . The impact on mass activity and mass transport resistance is analyzed as well. The effect of PSD evolution on the cell performance is discussed.


  • Open Access

    Simulating Morphology and Degradation of PEMFC Cathode Catalyst Layers with Porous Carbon Supports: Part I. Effect of Relative Humidity on Catalyst Utilization

    by Anne-Christine Scherzer, Patrick Schneider, Matthias Klingele, Nada Zamel, Dietmar Gerteisen

    We present a physical model of the cathode catalyst layer morphology which simulates the electrochemically active catalyst surface area at varying degrees of humidification. The model considers pore, particle and ionomer distributions and resulting interfaces on the nanoscale to create a unique mathematical representation of each material. Specifically, the model discriminates between catalyst particles on the support surface and inside primary pores of the support and their respective connection to the proton-conducting phase. Catalyst particles may be protonically activated by coverage with ionomer or water or be protonically inaccessible. The exact configuration depends on the particle size and location as well as the cell operating conditions, sensitizing the simulated catalyst utilization to these properties. Model results are compared against data for five samples with different support materials and ionomer loadings manufactured in-house. Further, trends in catalyst utilization which were observed in recent literature are reproduced with the model. This work provides a comprehensive analysis of material configurations and simulations at begin of test. In Part II, the presented model is integrated into a degradation model to predict the evolution of the electrode morphology and catalyst utilization during ageing.


  • Open Access

    Simulating Morphology and Degradation of PEMFC Cathode Catalyst Layers with Porous Carbon Supports: Part II. Effect of Ionomer and Relative Humidity on Catalyst Degradation

    by Anne-Christine Scherzer, Patrick Schneider, Matthias Klingele, Nada Zamel, Dietmar Gerteisen

    We present a physical degradation model which simulates the evolution of the cathode catalyst layer nanomorphology and associated catalyst surface area in the course of potential-induced ageing. By coupling to the morphology model featured in Part I, the effects of the pore, particle and ionomer distributions and resulting nanoscale interfaces in each individual material are taken into account. Specifically, the model discriminates between catalyst ageing on the support surface and inside primary pores of the support. For model validation, catalyst utilization data in terms of active surface area measured at varying relative humidity is used. These data are sensitive to a variety of electrode properties such as support porosity, catalyst loading and size and ionomer loading. Simulations are compared against data from 15 samples manufactured in-house using different materials and aged in different conditions. In-depth analysis of simulation results identifies the model as a valuable tool to establish a link between electrode composition and nanomorphology as well as between nanomorphology and expected degradation.


  • Open Access

    The Effect of Ionomer to Carbon Ratio and Relative Humidity on Cathode Catalyst Degradation in PEM Fuel Cells

    by Patrick Schneider, Anne-Christine Scherzer, Brian D. Storey, Matthias Klingele, Nada Zamel, Dietmar Gerteisen

    The effect of ionomer to carbon (I/C) weight ratio and relative humidity (RH) on cathode catalyst degradation was investigated by comprehensive in situ characterization. Membrane electrode assemblies (MEA) with I/C ratios of 0.5, 0.8 and 1.2 were subjected to an accelerated stress test performed at 40, 70 and 100% RH. The results show an increasing loss in electrochemical active surface area (ECSA) for both higher I/C ratios and RH during voltage cycling. To differentiate between ionomer and water connected ECSA, carbon monoxide stripping measurements were performed at varying RH. Before degradation, all MEAs show comparable total ECSA values, while higher I/C ratios lead to a larger fraction of ionomer connected ECSA. After degradation, ECSA measurements of the lowest I/C ratio showed a relatively higher loss of Pt in contact with ionomer than Pt in contact with water, while an opposite trend was observed for higher I/C ratios. H2/N2 impedance measurements showed drastically increasing protonic catalyst layer resistances for decreasing RH especially at low I/C ratios, which might hinder Pt2+ ion diffusion towards the membrane, hence decreasing the ECSA loss. Limiting current measurements show increasing molecular O2 diffusion resistances at end of test for samples with higher I/C ratios and higher ECSA loss.


  • Open Access

    Modeling the Morphological Effects of Catalyst and Ionomer Loading on Porous Carbon Supports of PEMFC

    by Anne-Christine Scherzer, Patrick Schneider, Patrick K. Herring, Matthias Klingele, Nada Zamel, Dietmar Gerteisen

    We present a model of the cathode catalyst layer morphology before and after loading a porous catalyst support with Pt and ionomer. Support nanopores and catalyst particles within pores and on the support surface are described by size distributions, allowing for qualitative processes during the addition of a material phase to be dependent on the observed pore and particle size. A particular focus is put on the interplay of pore impregnation and blockage due to ionomer loading and the consequences for the Pt/ionomer interface, ionomer film thickness and protonic binding of particles within pores. We used the model to emulate six catalyst/support combinations from literature with different porosity, surface area and pore size distributions of the support as well as varying particle size distributions and ionomer/carbon ratios. Besides providing qualitatively and quantitatively accurate predictions, the model is able to explain why the protonically active catalyst surface area has been reported to not increase monotonically with ionomer addition for some supports, but rather decrease again when the optimum ionomer content is exceeded. The proposed model constitutes a fast translation from manufacturing parameters to catalyst layer morphology which can be incorporated into existing performance and degradation models in a straightforward way.


  • Open Access

    Fast and Reliable State-of-Health Model of a PEM Cathode Catalyst Layer

    by Patrick Schneider, Christian Sadeler, Anne-Christine Scherzer, Nada Zamel, Dietmar Gerteisen

    Long-term stability of polymer electrolyte membrane fuel cells under dynamic operation still has a high potential for optimization, specifically for use in the automotive industry. This stability is especially affected by the degradation processes taking place in the cathode catalyst layer and hence should be fully understood. In this work, we develop a fast and reliable state-of-health model of the cathode catalyst layer, incorporating the electrochemical degradation processes related to anodic and cathodic platinum dissolution, oxidation, Pt loss due to ion diffusion, carbon corrosion and place exchange mechanisms as well as their interaction. For the purpose of validation, the model is developed alongside a comprehensive experimental data set. A detailed parameter study taking into account temperature, relative humidity and load profile dependency was carried out. A good agreement between model and experiment was found for load ranges between 0.6 and 0.95 V. Further, good approximation of the active surface area loss for cell temperatures between 60°C and 90°C and relative humidity between 30% and 100% were achieved.


  • Characteristic Time Constants Derived From the Low-Frequency Arc of Impedance Spectra of Fuel Cell Stacks

    by Stefan Keller, Tansu Özel, Anne-Christine Scherzer, Dietmar Gerteisen, Ulf Groos, Christopher Hebling, Yiannos Manoli

    Electrochemical impedance spectroscopy is used during operation of different polymer electrolyte membrane fuel cell (PEMFC) stack assemblies at various conditions with special interest given to the characteristic time constant τlow-f derived from the low-frequency arc of the spectra which is typically in the range of approximately 15–0.5 Hz. This was done by fitting an equivalent electrical circuit (EEC) consisting of one resistor and two RC-elements to the data. Parameter variation performed on a 90-cell stack assembly suggests that conditions leading to different air flow velocities in the flow channels affect τlow-f while other parameters like humidity influence the impedance spectrum, but not τlow-f. Comparison of the stoichiometry variation between short stack and locally resolved single cell shows similar results with the stack's time constant matching that of the cell's segments which are located off-center toward the outlet. However, a nonlinear dependency between gas flow velocity and τlow-f especially at low stoichiometric values is obvious. Results from stoichiometry variations at different pressure levels suggest that this could be attributed to the different steady-state oxygen partial pressures during the experiments. Comparison of the stoichiometry variation between different stack platforms result in similar dependencies of τlow-f on air flow rate with respect to a reference oxygen partial pressure regardless of size, flow field, geometry, or cell count of the stack. The time constant caused by oxygen diffusion through the gas diffusion layer (GDL), τGDL, was approximated and compared to τlow-f. While it was found that τlow-f ≫ τGDL at low stoichiometric values, τlow-f decreases toward τGDL at very high gas flow rates, suggesting that τGDL offsets τlow-f and becomes dominating if no oxygen concentration variation along the flow channel was present.